Siemens SITRANS F C MASSFLO MASS 6000 User manual

*083R9089*
Operating Manual
Order no.: FDK:521H0991
SFIDK.PS.028.M1.02 - A5E00253658
SITRANS F C MASSFLO


MASS flowmeters
Signal converter type MASS 6000
[]
s

SITRANS F C MASSFLO


2SFIDK.PS.028.M1.02
Mount the sensor on a vibration-free wall or
steel frame as shown.
Ensure that the sensor is not emptied of liquid
(during normal operation) otherwise incorrect
measurement will occur.
With low flow, horizontal mounting is recom-
mended, as in this position air bubbles are
easier to remove.
Locate the sensor low in the system in order to
avoid an under-pressure in the sensor seperat-
ing air/gas in the liquid.
If the liquid is volatile or contains solid parti-
cles, vertical mounting is not recommended.
Always locate the flowmeter as far away as
possible from components that generate me-
chanical vibration in the piping.
Cross talk between sensors mounted close to
each other may disturb the measurement. To
avoid cross talk never mount more than one
meter on each frame and mount flexible hose
connections between the sensors as shown.
Horizontal mounting
Vertical mounting
Vibration
Cross talk
1. Installation of sensor
To facilitiate zero-point adjustment, a valve with
good shut-off should always be mounted in
connection with the sensor as a proper zero-
point setting is essential for a good accuarcy.
Zero-point adjustment
1. Installation of sensor
Contents 1. Installation of sensor ..................................................................................................... 2
2. Installation of signal converter ..................................................................................... 3
2.1 Compact installation ....................................................................................................... 3
2.2.1 Remote Installation ......................................................................................................... 4
At the sensor ...................................................................................................................4
2.2.2 Remote installation ......................................................................................................... 5
Wall mounting ................................................................................................................. 5
Compact IP 67 version .................................................................................................... 5
2.2.3 Remote installation ......................................................................................................... 6
Signal converter in 19" insert .......................................................................................... 6
3. Technical data ................................................................................................................ 7
3.1 Signal converter MASS 6000 .......................................................................................... 7
4. Electrical connection ..................................................................................................... 8
4.1 Signal converter MASS 6000 .......................................................................................... 8
4.2 Output characteristics MASS 6000 ................................................................................. 9
5. Commissioning ............................................................................................................ 10
5.1 Menu overview .............................................................................................................. 10
5.2 Menu details .................................................................................................................. 11
5.3 Outputs setting menu .................................................................................................... 12
6. Service.......................................................................................................................... 14
6.1 List of error numbers ..................................................................................................... 14
6.2 Trouble shooting MASS 6000 ....................................................................................... 15
- this page has been updated 2004.05
Potential Hazards
The mains protective earth wire must be connected to the PE terminal in accordance with
the diagram.

SITRANS F C MASSFLO


3
SFIDK.PS.028.M1.02
2. Installation of signal converter
2. Installation of signal
converter
2.1 Compact installation
Remove and discard the terminal box lid of the
sensor.
1
2
3
Fit the PG 13.5 cable glands for the supply and
output cables.
Fit the supply and output cables respectively
and tighten the cable glands to obtain optimum
sealing.
Please see the wiring diagram for the "Electri-
cal connections".
Mount the signal converter on the terminal box.

SITRANS F C MASSFLO


4SFIDK.PS.028.M1.02
Mount the adaptor on top of the sensor inter-
face, if not already mounted.
When fitting the multiple plug, please make
sure that it is correctly oriented (note the little
tap).
2. Installation of signal converter
2.2.1 Remote Installation
At the sensor
The adaptor can be oriented in 4 directions.
Tighten the 4 screws with a 4 mm allern key to
secure the adaptor.
Mount the multiple plug in the adaptor and
tighten the glands on the plug to obtain opti-
mum sealing.
Note the wire colours when connecting the
MASS 6000. Refer to the diagram for electrical
wiring, see page 8.

SITRANS F C MASSFLO


5
SFIDK.PS.028.M1.02
2. Installation of signal converter
2.2.2 Remote installation
Wall mounting
Compact IP 67
version
Take the SENSORPROM®memory unit from
the sensor. Mount the SENSORPROM®unit in
the wall mounting unit as shown. The text on the
SENSORPROM®unit must turn towards the
wall bracket.
Mount the connection plate in the terminal box.
Tighten the earthing screw in the centre of the
connection box properly.
Fit the sensor, supply and output cables re-
spectively and tighten the cable glands to ob-
tain optimum sealing. Please see the wiring
diagram for the "Electrical connections".
Mount the signal converter on the terminal box.
Mount the wallbracket on a wall, pipe or in the
back of a panel.

SITRANS F C MASSFLO


6SFIDK.PS.028.M1.02
2. Installation of signal converter
2.2.3 Remote installation
Signal converter in
19" insert
1. Fit the SENSORPROM®unit on the connection board supplied with the signal converter. The
SENSORPROM®unit is supplied with the sensor.
2. Mount the guide rails in the rack system as shown. Distance between guide rails is 21 TE.
Guide rails are supplied with the rack system and not with the signal converter.
3. Mount the connection board as shown. The left side of the connection board must flush to the
left of the guide rail.
4. Connect the cables as shown under "Electrical connection".
5. Plug the signal converter into the rack system.

SITRANS F C MASSFLO


7
SFIDK.PS.028.M1.02
3. Technical data
Measurement of Mass flow [kg/s], volume flow [l/s], fraction [%], Brix, density [kg/m3], temperature [°C]
Current output
Current 0-20 mA or 4-20 mA
Load < 800 ohm
Time constant 0-30 s adjustable
Digital output
Frequency 0-10 kHz, 50% duty cycle
Time constant 0-30 s adjustable
Active 24 V d.c., 30 mA, 1 KΩ≤ Rload ≤ 10 KΩ, short-circuit-protected
Passive 3-30 V d.c., max. 110 mA, 1 KΩ≤ Rload ≤ 10 KΩ
Relay
Type Change-over relay
Load 42 V / 2 A peak
Functions Error level, error number, limit, direction
Digital input 11-30 V d.c.
Functionality Start/hold/continue batch, zero-point adjust, reset totalizer 1/2, force output, freeze output
Galvanic isolation All inputs and outputs are galvanically isolated, isolation voltage 500 volts
Cut-off
Low-flow 0-9.9% of maximum flow
Limit function Mass flow, volume flow, fraction, density, sensor temperature
Totalizer Two eight-digit counters for forward, net or reverse flow
Display Background illumination with alphanumerical text, 3 × 20 characters to indicate flow rate, totalized
values, settings and faults.
Reverse flow indicated by negative sign
Zero-point adjustment Manual via keypad or remote via digital input
Ambient temperature Operation: −20 to +50°C
During storage: −40 to +70°C (Humidity max. 95%)
Communication Prepared for client mounted add-on modules
Enclosure compact IP 67
Material Fibre glass-reinforced polyamide
Rating IP 67 to IEC 529 and DIN 40050 (1 m w.g. for 30 min.)
Mechanical load 18-1000 Hz random, 3.17G rms, in all directions, to IEC 68-2-36
Enclosure 19"
Material Aluminium/steel (DIN 41494)
Rating IP 20 to IEC 529 and DIN 40050 (1 m w.g. for 30 min.)
Mecanical load 18-1000 Hz random, 3.17G rms, in all directions, to IEC 68-2-36
Supply voltage 115/230 V a.c. +10% to −10%, 50-60 Hz
18-30 V d.c. or 20-30 V a.c.
Power consumption 230 V a.c.: 9 VA max.
24 V d.c.: 6 W IN= 250 mA, IST = 2A (30 msec)
EMC performance
Emission EN 50081-1 (Light industry)
Immunity EN 50082-2 (Industry)
Ex-approval [EEx ia] II C, DEMKO Ex99E.125729X
Maintenance The flowmeter has a built-in error log/pending menu which should be inspected on a regular basis
Fuse T 400 mA, T 250 V (IEC 127). Not replaceable by operator
3. Technical data
3.1 Signal converter MASS 6000
MASS 6000 Compact IP 67 and 19" IP 20 version

SITRANS F C MASSFLO


8SFIDK.PS.028.M1.02
4. Electrical connection
4.1 Signal converter
MASS 6000
4. Electrical connection
- this page has been updated 2004.05
Installation 1) Mains supply 115 to 230 V a.c. from building installation Class II. A switch or circuit-breaker
(max. 15 A) shall be included in the building installation. It must be in close proximity to the
equipment and within easy reach of the OPERATOR, and it shall be marked as the
disconnecting device for the equipment.
2) The mains protective earth wire must be connected to the PE terminal, if the earth
wire is not connected, personnel can be exposed to 115V/230V.
Required cable min. AGW16 or 1.5 mm2 Cu wire.
The insulation between the connected mains supply and 24 V a.c./d.c. supply for the flow-
meters, models 24 V a.c./d.c. shall at least be rated with double or reinforced insulation at
mains voltage.
For field wiring installation National Installation Code shall be met of the country, where the
flowmeters are installed.
Main voltage terminals must be out of reach for OPERATOR to avoid any hazards!
Digital output
If the internal resistance of the loads exceeds 10KΩ, it is recommended to connect an external
10KΩload resistor in parallel to the load.

SITRANS F C MASSFLO


9
SFIDK.PS.028.M1.02
4. Electrical connection
4.2 Output characteristics
MASS 6000 Output characteristics Bidirectional mode Unidirectional mode
0-20 mA
4-20 mA
Frequency
Pulse output
Relay Power supply off Power supply on
Error relay No error Error
Limit switch or 1 set point 2 set points
direction switch
Low flow Intermediate flow
(Reverse flow)
High flow High flow/
(Forward flow) Low flow
Batch on digital
output

SITRANS F C MASSFLO


10 SFIDK.PS.028.M1.02
5. Commissioning
5.1 Menu overview
5. Commissioning