Siemens SITRANS F FC410 User manual

These Operating Instructions apply to Siemens
product SITRANS FC410 with order codes
commencing 7ME4611, 7ME4621 and 7ME4711.
02/2016
A5E33120874-AC
Introduction
1
Safety notes
2
Description
3
Installing/Mounting
4
Connecting
5
Commissioning
6
Functions
7
Alarms and system
messages
8
Service and maintenance
9
Troubleshooting/FAQs
10
Technical data
11
Spare parts and accessories
12
Dimensions and weight
13
Modbus holding registers
A
Sensor dimension
dependent default settings
B
Zero point adjustment
C
CRC calculation
D
Exception codes
E
Float definition
F
SITRANS F
Coriolis Flowmeters
FC410 with Modbus
Operating Instructions

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E33120874
Ⓟ
03/2016 Subject to change
Copyright © Siemens AG 2013 - 2016.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury
may
result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper useof Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer ofLiability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 3
Table of contents
1 Introduction............................................................................................................................................. 7
1.1 History.......................................................................................................................................7
1.2 Items supplied...........................................................................................................................8
1.3 Checking the consignment .......................................................................................................8
1.4 Device identification ..................................................................................................................9
1.5 Further Information .................................................................................................................14
2 Safety notes.......................................................................................................................................... 15
2.1 Laws and directives ................................................................................................................15
2.2 Installation in hazardous locations..........................................................................................16
2.3 Certificates ..............................................................................................................................20
3 Description............................................................................................................................................ 21
3.1 Design.....................................................................................................................................22
3.2 System integration ..................................................................................................................23
3.3 Modbus RTU technology ........................................................................................................23
3.4 Features..................................................................................................................................25
3.5 Theory of operation.................................................................................................................25
4 Installing/Mounting ................................................................................................................................ 27
4.1 Flowmeter installation .............................................................................................................27
4.1.1 Installation safety precautions ................................................................................................27
4.1.2 Determining a location ............................................................................................................28
4.1.3 Orientation of the device.........................................................................................................29
4.1.4 Mounting the flowmeter...........................................................................................................32
4.1.5 Hydrostatic testing ..................................................................................................................34
4.1.6 Mounting a pressure guard.....................................................................................................34
5 Connecting ........................................................................................................................................... 37
5.1 Wiring in hazardous locations.................................................................................................37
5.2 Cable requirements.................................................................................................................37
5.3 Safety notes for connecting ....................................................................................................38
5.4 Connecting the FC410............................................................................................................39
5.4.1 M12 version (for non-Ex areas) ..............................................................................................39
5.4.2 Cable termination version .......................................................................................................40
5.4.3 Setting the EOL termination DIP switches..............................................................................42
5.5 Integrating the FC410 with Modbus system ...........................................................................43
5.5.1 System configurations.............................................................................................................43
5.5.2 Wiring FC410 to the Modbus system......................................................................................48

Table of contents
FC410 with Modbus
4Operating Instructions, 02/2016, A5E33120874-AC
6 Commissioning ..................................................................................................................................... 51
6.1 General requirements ............................................................................................................ 51
6.2 Warnings ................................................................................................................................ 51
6.3 Operating via SIMATIC PDM ................................................................................................. 51
6.4 Functions in SIMATIC PDM ................................................................................................... 52
6.5 Commissioning steps............................................................................................................. 52
6.6 Initial setup ............................................................................................................................. 52
6.7 Adding device to communication network ............................................................................. 54
6.8 Configuring a new device....................................................................................................... 55
6.9 Wizard - Quick Start via PDM ................................................................................................ 56
6.10 Wizard - Zero Point adjustment ............................................................................................. 62
6.11 Changing parameter settings using SIMATIC PDM .............................................................. 64
6.12 Parameters accessed via drop-down menus......................................................................... 64
6.13 Zero point adjustment ............................................................................................................ 65
6.14 Process variables................................................................................................................... 67
7 Functions.............................................................................................................................................. 69
7.1 Process values....................................................................................................................... 69
7.2 Zero point adjustment ............................................................................................................ 69
7.3 Low flow cut-off ...................................................................................................................... 71
7.4 Empty tube monitoring ........................................................................................................... 72
7.5 Process noise damping.......................................................................................................... 73
7.6 Totalizer ................................................................................................................................. 75
7.7 Access management ............................................................................................................. 75
7.8 Simulation .............................................................................................................................. 76
7.9 Changing Modbus communication settings ........................................................................... 77
7.10 Float transmission.................................................................................................................. 77
8 Alarms and system messages............................................................................................................... 79
8.1 Alarm messages .................................................................................................................... 79
9 Service and maintenance...................................................................................................................... 81
9.1 Maintenance........................................................................................................................... 81
9.2 Maintenance information parameters .................................................................................... 81
9.3 Service information ................................................................................................................ 81
9.4 Recalibration .......................................................................................................................... 82
9.5 Technical support................................................................................................................... 82
9.6 Transportation and storage.................................................................................................... 83
9.7 Device disposal ...................................................................................................................... 83
9.8 Maintenance work.................................................................................................................. 84

Table of contents
FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 5
10 Troubleshooting/FAQs .......................................................................................................................... 85
10.1 Diagnosing with PDM..............................................................................................................85
10.2 Troubleshooting ......................................................................................................................85
11 Technical data...................................................................................................................................... 91
11.1 Function and system design ...................................................................................................91
11.2 Process variables....................................................................................................................91
11.3 Modbus Communication Specification....................................................................................92
11.4 Performance ...........................................................................................................................93
11.5 Rated operating conditions .....................................................................................................94
11.6 Pressure drop curves..............................................................................................................95
11.7 Pressure - temperature ratings ...............................................................................................95
11.7.1 Stainless steel sensors ...........................................................................................................96
11.7.2 Hastelloy sensors....................................................................................................................98
11.8 Design.....................................................................................................................................99
11.9 Power supply ........................................................................................................................100
11.10 Basic electrical requirement for master system....................................................................100
11.11 Cables and cable entries ......................................................................................................101
11.12 Installation torques................................................................................................................102
11.13 Certificates and approvals ....................................................................................................102
11.14 PED.......................................................................................................................................103
12 Spare parts and accessories ............................................................................................................... 109
12.1 Ordering ................................................................................................................................109
12.2 Ex approved products...........................................................................................................109
12.3 Replaceable components .....................................................................................................110
13 Dimensions and weight ....................................................................................................................... 111
13.1 Sensor dimensions ...............................................................................................................111
13.2 Length matrix ........................................................................................................................112
13.3 316L stainless steel - NAMUR..............................................................................................114
13.4 Hygienic versions..................................................................................................................116
A Modbus holding registers .................................................................................................................... 117
A.1 Modbus addressing model....................................................................................................117
A.2 Modbus function codes.........................................................................................................117
A.3 Modbus holding registers tables ...........................................................................................122
A.3.1 Process values......................................................................................................................123
A.3.2 Identification..........................................................................................................................123
A.3.3 Setup.....................................................................................................................................124
A.3.4 Totalizer ................................................................................................................................126

Table of contents
FC410 with Modbus
6Operating Instructions, 02/2016, A5E33120874-AC
A.3.5 Maintenance & Diagnostics ................................................................................................. 128
A.3.6 Communication .................................................................................................................... 132
A.3.7 Characteristics ..................................................................................................................... 133
A.3.8 Simulation ............................................................................................................................ 135
A.3.9 Alarms .................................................................................................................................. 136
A.3.10 Quality codes for process values ......................................................................................... 138
B Sensor dimension dependent default settings ......................................................................................139
C Zero point adjustment ..........................................................................................................................141
D CRC calculation ...................................................................................................................................145
E Exception codes ..................................................................................................................................149
E.1 Exception handling............................................................................................................... 149
F Float definition .....................................................................................................................................151
F.1 Float definition...................................................................................................................... 151
Glossary ..............................................................................................................................................153
Index ...................................................................................................................................................155

FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 7
Introduction
1
These instructions contain all information required to commission and use the device. Read
the instructions carefully prior to installation and commissioning. In order to use the device
correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
The contents of this manual shall not become part of or modify any prior or existing
agreement, commitment or legal relationship. The sales contract contains all obligations on
the part of Siemens as well as the complete and solely applicable warranty conditions. Any
statements regarding device versions described in the manual do not create new warranties
or modify the existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right
to make technical changes in the course of further development.
1.1 History
The following table shows major changes in the documentation compared to the previous
edition.
Edition
Remarks
SW version
FW revision
12/2013 •First edition •SIMATIC PDM driver 1.00.01-01 2.03.02-01
05/2015 •Update of SIMATIC PDM ver. 8
•Update of Modbus holding registers:
Modbus address 2215 to 2218 added.
•SIMATIC PDM driver 1.01.00-00 2.03.03-01
02/2016 •EAC Ex declaration information added •SIMATIC PDM driver 1.01.00-00 2.03.03-01

Introduction
1.2 Items supplied
FC410 with Modbus
8Operating Instructions, 02/2016, A5E33120874-AC
1.2 Items supplied
With M12 plug connection
•
SITRANS FC410 flowmeter
•
Sensor cable with M12 connector
•
SD card with production certificates
•
Quick Start guide
•
CD containing software, certificates
and device manuals
With sensor terminal housing
•
SITRANS FC410 flowmeter
•
Sensor cable
•
Packet of cable glands
•
SD card with production certificates
•
Quick Start guide
•
CD containing software, certificates
and device manuals
Note
Supplementary information
Supplementary product and production specific certificates are included on the
SensorFlash® SD card.
Note
Scope of delivery may vary, depending on version and add
-ons. Make sure the scope of
delivery and the information on the nameplate correspond to your order and the delivery
note.
1.3 Checking the consignment
1. Check the packaging and the delivered items for visible damage.
2. Report any claims for damages immediately to the shipping company.

Introduction
1.4 Device identification
FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 9
3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Danger of explosion in hazardous areas.
•Do not use damaged or incomplete devices.
1.4 Device identification
Each part of the FC410 Coriolis flowmeter has three nameplate types showing the following
information:
●product identification
●product specifications
●certificates and approvals
Note
Identification
Identify your device by comparing your ordering data with the information on the product
and specification nameplates.
FC410 sensor identification nameplate
①
Product name
Sensor product name
②
Serial no.
Flowmeter serial number
③
Sen. RS
Mechanical sensor version number
④
Manufacturer
Manufacturer name and location
⑤
Country
Manufacturing country
⑥
System order no.
Device-specific system order number
Image 1-1 FC410 identification nameplate example

Introduction
1.4 Device identification
FC410 with Modbus
10 Operating Instructions, 02/2016, A5E33120874-AC
Flowmeter serial number construction
The flowmeter serial number is constructed as follows:
PPPYMDDxxxxxx
where
PPP = Production factory (Siemens Flow Instruments: FDK)
Y = Production year (for encryption, see below)
M = Production month (for encryption, see below)
DD = Production date (for encryption, see below)
xxxxxx = Sequential number
Encryption:
Calendar year (Y)
Code
1950, 1970, 1990, 2010
A
1951, 1971, 1991, 2011
B
1952, 1972, 1992, 2012
C
1953, 1973, 1993, 2013
D
1954, 1974, 1994, 2014
E
1955, 1975, 1995, 2015
F
1956, 1976, 1996, 2016
H (G)
1957, 1977, 1997, 2017
J
1958, 1978, 1998, 2018
K
1959, 1979, 1999, 2019
L
1960, 1980, 2000, 2020
M
1961, 1981, 2001, 2021
N
1962, 1982, 2002, 2022
P
1963, 1983, 2003, 2023
R
1964, 1984, 2004, 2024
S
1965, 1985, 2005, 2025
T
1966, 1986, 2006, 2026
U
1967, 1987, 2007, 2027
V
1968, 1988, 2008, 2028
W
1969, 1989, 2009, 2029
X
Month (M)
Code
January
1
February
2
March
3
April
4
May
5
June
6
July
7
August
8
September
9

Introduction
1.4 Device identification
FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 11
October
O
November
N
December
D
Date (DD)
Code
Day 1 to 31
01 to 31 (corresponding to the actual date)
FC410 sensor specification nameplate
①
EX approvals
Ex approval specifications for the sensor (ATEX example)
②
Consult the operating instructions
③
CE
CE mark
④
0539
Notified Body ID (ATEX)
⑤
Ex
Ex mark
⑥
MAWP Maximum allowable working pressures at 20 °C (68 °F) and 200 °C
(392 °F) (max. temperature)
⑦
Fluid group
Fluid group statement required by PED
⑧
Wetted material
Tube/process connection materials
⑨
Min. fluid temperature
Minimum fluid temperature
⑩
Size DN
Nominal size
⑪
Conn.
Process connection type and size
⑫
Year of Manufacture Manufacturing year
More detailed manufacturing date information is given in the serial
number found on the identification nameplate
⑬
Cal. Factor
Calibration factor
⑭
Qm (min)
Qm (nom)
Minimum and nominal flows with water at 20 °C (68 °F)
⑮
Enclosure IP
Degree of protection
⑯
Ambient Temp.
Ambient temperature range
⑰
Accuracy
Accuracy for massflow and density
Image 1-2 FC410 specification nameplate example

Introduction
1.4 Device identification
FC410 with Modbus
12 Operating Instructions, 02/2016, A5E33120874-AC
FC410 Mini Flow Link (MFL) identification nameplate
①
Product name
Name of device
②
Power supply
Power supply
③
Communication
Communication: Modbus Master/Slave RTU technology
④
Address range
Modbus device address range
⑤
Manufacturer
Manufacturer name and location
⑥
Country
Manufacturing country
⑦
HW
Hardware version
⑧
FW
Firmware version
Image 1-3 FC410 Mini Flow Link identification nameplate
Note
Approval identifications
Approval certificates and notified body identifications are available for download at
siemens.com
FC410 sensor approval nameplate
①
QR code
Product-specific QR code
②
C✓
C-tick logo
③
3A
3A logo
④
WEEE (Page 83)
Image 1-4 FC410 approval nameplate example

Introduction
1.4 Device identification
FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 13
Note
Logos and warnings
Logos and warnings are only shown on the product where applicable. The combination
shown in the example above is relevant for a hygienic sensor.
The Australian C
-tick mark is mandatory on all products.
FC410 EHEDG nameplate
Image 1-5 EHEDG nameplate
This nameplate appears on all Hygienic sensors 7ME462.
Other label
Image 1-6 How to install
The QR code provides direct internet connection to
●The product support portal, which includes access to the How to Install YouTube video.
(This example provides that function.)
●Product and production-specific documentation maintained in the production database.

Introduction
1.5 Further Information
FC410 with Modbus
14 Operating Instructions, 02/2016, A5E33120874-AC
1.5 Further Information
Product information on the Internet
The Operating Instructions are available on the documentation disk shipped with the device,
and on the Internet on the Siemens homepage, where further information on the range of
SITRANS F flowmeters may also be found:
Product information on the internet (http://www.siemens.com/flow)
Worldwide contact person
If you need more information or have particular problems not covered sufficiently by these
Operating Instructions, get in touch with your contact person. You can find contact
information for your local contact person on the Internet:
Local contact person (http://www.automation.siemens.com/partner)

FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 15
Safety notes
2
This device left the factory in good working condition. In order to maintain this status and to
ensure safe operation of the device, observe these instructions and all the specifications
relevant to safety.
Observe the information and symbols on the device. Do not remove any information or
symbols from the device. Always keep the information and symbols in a completely legible
state.
Symbol
Explanation
Consult operating instructions
2.1 Laws and directives
Observe the test certification, provisions and laws applicable in your country during
connection, assembly and operation. These include, for example:
●National Electrical Code (NEC - NFPA 70) (USA)
●Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
●IEC 60079-14 (international)
●EN 60079-14 (EC)
Conformity with European directives
The CE marking on the device symbolizes the conformity with the following European
directives:
Electromagnetic compatibil
i-
ty EMC
2004/108/EC
Directive of the Europe
an Parliament and of the Council on the
approximation of the laws of the Member States relating to
electromagnetic compatibility and repealing Directive
89/336/EEC.
Low voltage directive LVD
2006/95/EC
Directive of the European Parliament and of the Council on the
harmonisation of the laws of Member States relating to electr
i-
cal equipment designed for use within certain voltage limits.

Safety notes
2.2 Installation in hazardous locations
FC410 with Modbus
16 Operating Instructions, 02/2016, A5E33120874-AC
Atmosphère explosible
ATEX
94/9/EC
Directive of the European Parlia
ment and the Council on the
approximation of the laws of the Member States concerning
equipment and protective systems intended for use in potentia
l-
ly explosive atmospheres.
Pressure equipment direct
i-
ve PED
97/23/EC
Directive of the European Parliament
and of the Council on the
approximation of the laws of the Member States concerning
pressure equipment.
The applicable directives can be found in the EC conformity declaration of the specific
device. Further country or region-specific code conformity information is available on
request.
WARNING
Improper device modifications
Danger to personnel, system and environment can result from modifications to the device,
particularly in hazardous areas.
•Only carry out modifications that are described in the instructions for the device. Failure
to observe this requirement cancels the manufacturer's warranty and the product
approvals.
Note
CE declaration
The CE declaration certificate is available on the SensorFlash SD card delivered with the
device.
Note
EAC declaration
The EAC declaration is available on the SensorFlash SD card delivered with the device.
2.2 Installation inhazardous locations
WARNING
Equipment used in hazardous locations
Equipment used in hazardous locations must be Ex-approved for the region of installation
and marked accordingly. It is required that the special conditions for safe use provided in
the manual and in the Ex certificate are followed!

Safety notes
2.2 Installation in hazardous locations
FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 17
Hazardous location approvals
The device is approved for use in hazardous locations and has the approvals listed below.
Special conditions for safe installation and operation specified by each approval authority are
included in the relevant certificate.
ATEX:
FC410 flowmeter (can be installed in Zone 1 for gas and Zone 20/21 for dust):
Certificate: SIRA 11ATEX1341X
II 1/2 G
1D
2D
For gas:
Ex d ia IIC T* Ga/Gb
Ex d IIC T* Ga/Gb
(Ga/Gb: Zone 0 in pipe and Zone 1 in environment)
For dust:
Ex ta IIIC T* °C Da
Ex tb IIIC T* °C Db
(Zone 20 ("ta") process and ambient temperature limited in comparison with Zone 21 ("tb")
Ta = -40°C to +60°C
* Temperature class (dependent on the process temperature and the ambient temperatur)
IECEx:
FC410 flowmeter (can be installed in Zone 1 for gas and Zone 20/21 for dust):
Certificate: IECEx SIR 11.0149X
For gas:
Ex d ia IIC T* Ga/Gb
Ex d IIC T* Ga/Gb
(Ga/Gb: Zone 0 in pipe and Zone 1 in environment)
For dust:
Ex ta IIIC T* °C Da
Ex tb IIIC T* °C Db
(Zone 20 ("ta") process and ambient temperature limited in comparison with Zone 21 ("tb")
(Ta = -40°C to +60°C)
* Temperature class (dependent on the process temperature and the ambient temperature)
EAC Ex
FC410 flowmeter / -40°C ≤ Tamb ≤ ** °C
1Ex d ia IIC T* Ga/Gb
Ex ta IIIC T** °C Da
Ex tb IIIC T** °C Db

Safety notes
2.2 Installation in hazardous locations
FC410 with Modbus
18 Operating Instructions, 02/2016, A5E33120874-AC
FM:
Sensor with Mini Flow Link (MFL) (FC410):
Class I, II, III Division 1
Groups A, B,C, D, E, F, G
Class I Zone1 and Zone 20/21
Note
Control drawing
See Control
drawing: A5E31205486A
Maximum temperature specifications for Exuse
Device temperature classification with and without dust is related to the process temperature
and ambient temperature as listed below.
The maximum allowable process fluid temperatures with respect to temperature class for the
device when used with potentially explosive gases in a maximum ambient temperature of
+60°C are:
Ta (°C)
Maximum Process Temperature per Temperature Class (°C)
T6
T5
T4
T3
60
70
70
70
70
55
85
100
100
100
50
85
100
130
130
45
85
100
135
160
40
85
100
135
190
35
85
100
135
200
30
85
100
135
200
If the equipment is placed in a "tb" environment (Zone 21), the maximum process
temperatures shall be as follows:
Ta (°C)
Maximum Process Temperature per Temperature Class (°C)
60
70
55
100
50
130
45
160
40
190
35
200
30
200
Additionally, the maximum surface temperature of the overall device shall be:
●If Tprocess ≤ 85°C, maximum surface temperature = 85°C.
●If Tprocess > 85°C, maximum surface temperature = process temperature.

Safety notes
2.2 Installation in hazardous locations
FC410 with Modbus
Operating Instructions, 02/2016, A5E33120874-AC 19
If the equipment is placed in a "ta" environment (Zone 20), the maximum process
temperature shall be as follows:
Ta (°C)
Maximum Process Temperature per Temperature Class (°C)
60
-40
55 -10
50
20
45 50
40
80
35
110
30
140
Special conditions for safe use
In general, it is required that:
●The equipment shall not be opened when energized and when an explosive gas or dust
atmosphere may be present..
●Appropriate cable connectors are used.
●Sensor is connected to the potential equalization throughout the hazardous area.
●EN/IEC 60079-14 is considered for installation in hazardous areas.
Further information and instructions including approval-specific special conditions for safe
use in Ex applications can be found in the certificates on the accompanying literature CD
and at www.siemens.com/FC410 (www.siemens.com/FC410).
WARNING
Laying ofcables
Explosion hazard
Cable for use in hazardous locations must satisfy the requirements for having a proof
voltage of at least 500 V AC applied between the conductor/ground, conductor/shield and
shield/ground.
Connect the devices that are operated in hazardous areas as per the stipulations applicable
in the country of operation.
WARNING
Field wiring installation
Ensure that the national requirements of the country in which the devices are installed are
met.

Safety notes
2.3 Certificates
FC410 with Modbus
20 Operating Instructions, 02/2016, A5E33120874-AC
2.3 Certificates
Certificates are posted on the online support portal
and can also be found on the documentation disk shipped with the device.
(http://www.siemens.com/processinstrumentation/certificates )
Certification documents including calibration report are supplied with each sensor included
on the SensorFlash. Material, pressure test, and factory conformance certificates are
optional at ordering.