Siemens SITRANS F MAG 6000 I User manual

SITRANS F
Electromagnetic flowmeters
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions
7ME693 (MAG 6000 I)
08/2018
A5E02083319-AH
Introduction 1
Safety notes 2
Description 3
Installing/Mounting 4
Connecting 5
Commissioning 6
Functions 7
Alarm, error, and system
messages 8
Service and maintenance 9
Troubleshooting/FAQs 10
Technical data 11
Spare parts/Accessories 12
Menu diagrams A
Factory settings B
Control drawing C

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E02083319
Ⓟ 08/2018 Subject to change
Copyright © Siemens AG 2018.
All rights reserved

Table of contents
1 Introduction...................................................................................................................................................7
1.1 Preface.....................................................................................................................................7
1.2 Items supplied..........................................................................................................................7
1.3 Revision history........................................................................................................................7
1.4 Device identification.................................................................................................................8
1.5 Further Information...................................................................................................................9
2Safety notes................................................................................................................................................11
2.1 General safety instructions.....................................................................................................11
2.2 Laws and directives................................................................................................................11
2.3 Installation in hazardous area................................................................................................12
2.3.1 ATEX 2 GD approval..............................................................................................................13
2.3.2 FM/CSA Class I, Zone 1 approval..........................................................................................17
2.3.3 FM Class I, II, III, Div 1 approval............................................................................................18
3 Description..................................................................................................................................................19
3.1 Applications............................................................................................................................19
3.2 System components...............................................................................................................19
3.3 Design....................................................................................................................................20
3.4 Features.................................................................................................................................21
3.5 Theory of operation................................................................................................................21
4 Installing/Mounting......................................................................................................................................23
4.1 Installation safety precautions................................................................................................23
4.2 Installation conditions.............................................................................................................23
4.3 Compact installation...............................................................................................................24
4.4 Remote installation.................................................................................................................25
4.4.1 Wall mounting using standard mounting plate.......................................................................27
4.4.2 Pipe or wall mounting with assembly bracket........................................................................27
5 Connecting.................................................................................................................................................29
5.1 Safety precautions.................................................................................................................30
5.2 Electrical connection..............................................................................................................31
5.3 Connection of sensor and transmitter in remote version........................................................34
5.4 Wiring in hazardous area.......................................................................................................37
5.5 Connection of bus communication add-on modules..............................................................38
5.6 Reassembling the device.......................................................................................................38
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 3

6 Commissioning...........................................................................................................................................41
6.1 Local user interface................................................................................................................41
6.2 Menu structure.......................................................................................................................43
6.3 Changing password...............................................................................................................43
6.4 Changing basic settings.........................................................................................................44
6.5 Changing operator menu setup..............................................................................................47
6.6 Changing language................................................................................................................48
7 Functions....................................................................................................................................................49
7.1 Introduction............................................................................................................................49
7.2 Output settings.......................................................................................................................49
7.3 External input.........................................................................................................................50
7.4 Sensor characteristics............................................................................................................51
7.5 Reset mode............................................................................................................................51
7.6 Service mode.........................................................................................................................51
8 Alarm, error, and system messages...........................................................................................................53
8.1 Diagnostics.............................................................................................................................53
8.2 List of error numbers..............................................................................................................55
9 Service and maintenance...........................................................................................................................57
9.1 Maintenance...........................................................................................................................57
9.2 Certificates.............................................................................................................................57
9.3 Technical support...................................................................................................................57
9.4 Return procedures.................................................................................................................58
10 Troubleshooting/FAQs................................................................................................................................61
10.1 Troubleshooting guide............................................................................................................61
10.2 Transmitter check list.............................................................................................................62
11 Technical data............................................................................................................................................65
11.1 Technical specifications.........................................................................................................65
11.2 Dimensions and weight..........................................................................................................67
11.3 Accuracy................................................................................................................................68
11.4 Output characteristics............................................................................................................69
11.5 Cable data..............................................................................................................................71
11.6 Cable requirements................................................................................................................72
12 Spare parts/Accessories.............................................................................................................................73
12.1 Ordering of spare parts..........................................................................................................73
12.2 Accessories............................................................................................................................73
Table of contents
4SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

12.3 Spare parts.............................................................................................................................74
A Menu diagrams...........................................................................................................................................75
A.1 Transmitter menu overview....................................................................................................75
A.2 Basic settings.........................................................................................................................77
A.3 Current output........................................................................................................................78
A.4 Digital output - pulse..............................................................................................................79
A.5 Digital output - frequency.......................................................................................................79
A.6 Error level...............................................................................................................................79
A.7 Error number..........................................................................................................................80
A.8 Direction/limit..........................................................................................................................80
A.9 Batch......................................................................................................................................81
A.10 External input.........................................................................................................................82
A.11 Sensor characteristics............................................................................................................83
A.12 Reset mode............................................................................................................................84
A.13 Service mode.........................................................................................................................85
A.14 Operator menu setup.............................................................................................................86
A.15 Product identity......................................................................................................................87
A.16 Add-on communication module..............................................................................................88
B Factory settings..........................................................................................................................................89
B.1 Transmitter factory settings....................................................................................................89
B.2 50 Hz Dimension dependent Qmax.......................................................................................91
B.3 60 Hz Dimension dependent Qmax.......................................................................................92
B.4 50 Hz Dimension dependent volume/pulse and batch...........................................................94
B.5 60 Hz Dimension dependent volume/pulse and batch...........................................................95
C Control drawing..........................................................................................................................................97
C.1 Control drawing......................................................................................................................97
Index.........................................................................................................................................................103
Table of contents
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 5

Table of contents
6SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

Introduction 1
1.1 Preface
These instructions contain all the information you need for using the device.
The instructions are aimed at persons mechanically installing the device, connecting it
electrically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
Note
It is the responsibility of the customer that the instructions and directions provided in the
operating instructions are read, understood, and followed by the relevant personnel before
installing the device.
1.2 Items supplied
● SITRANS F M MAG 6000 I or MAG 6000 I
Ex de transmitter
●Wall mounting bracket (remote version)
● SITRANS F M literature CD containing
software, certificates and device manuals
● Quick start guide
1.3 Revision history
The contents of these instructions are reviewed regularly and any corrections included in
subsequent editions. We welcome all suggestions for improvement.
The following table lists the most important changes made to the documentation in the current
and previous editions.
Edition Remarks HW version SW version
08/2018 ● Updated Safety Notes 08 4.08 X06
04/2016 ● Various technical specifications updated
● Control drawing updated
08 4.08 X06
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 7

Edition Remarks HW version SW version
01/2015 ● Graphics, technical data and factory settings changed
to comprise:
– "BBL42" is displayed as the default setting in
customer unit instead of "?". The unit can still be
changed.
– Improved minimum supply voltage for current
output to 12 V.
● Document revision identification changed according to
new SIEMENS standard
06 4.08 X06
09/2012 ● Enhanced current output function
● Updated menu functions; possibility of showing user
defined units in display
●Updated ATEX approval
● General update
06 4.07 X06
12/2011 ● Updated ATEX approval
●General update
04 4.07 X06
03/2011 ● First edition
●Transmitter upgrade information included
04 4.06 X06
1.4 Device identification
Inspection
1. Check for mechanical damage due to possible improper handling during shipment. All
claims for damage are to be made promptly to the carrier.
2. Make sure the scope of delivery, and the information on the namelate corresponds to the
ordering information
Introduction
1.4 Device identification
8SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

Identification

6,75$16)00$*,3
2UGHU1R6HULDO1R+:):
6XSSO\9$&+]RU9'&9$

(QFORVXUH6HQVRUPDWHULDO6L]H'1&DO)DFWRU/LQLQJ(OHFWURGHV3URFHVVFRQQHFWLRQ0$:336DWr&r)0$:336DWr&r))OXLGJURXS3('*,31(0$;$670$LQFK3)$+DVWHOOR\&
7UDQVPLWWHU6HQVRU
6LHPHQV$*'(.DUOVUXKH
0DGHLQ)UDQFH
,,*'0(<)*%+
(131EDUSVLEDUSVL<HDURI0DQXI
([GH>LD@LD,,&77*E([W'$,377
r&7D5HIHUWRXVHU,QVWUXFWLRQV3LSHWHPSHUDWXUH.EXWQRWOHVVWKDQr&,6,17(5)$&(6HHPDQXDO7PHGLDPD[r&r)7PHGLDPLQr&r)
6LUD$7(;;,(&([6,5;6LUD$7(;;,(&([6,5;
&RPPXQLFDWLRQ+$57
①Code number
②Serial number
③Power supply
④Enclosure rating
⑤MAWP (Maximum Allowable Working Pressure) at defined temperature, e.g. 25 °C
⑥Fluid group statement required by PED
⑦Communication module dellivered with the flowmeter
⑧Approvals
⑨Media temperature
Figure 1-1 Example of MAG 6000 I Ex nameplate
1.5 Further Information
Product information on the Internet
The Operating Instructions are available on the documentation disk shipped with the device,
and on the Internet on the Siemens homepage, where further information on the range of
SITRANS F flowmeters may also be found:
Product information on the internet (http://www.siemens.com/flowdocumentation)
Worldwide contact person
If you need more information or have particular problems not covered sufficiently by these
Operating Instructions, get in touch with your contact person. You can find contact information
for your local contact person on the Internet:
Local contact person (http://www.automation.siemens.com/aspa_app/contactmenu.aspx?
ci=yes&regid=DEF&lang=en)
Introduction
1.5 Further Information
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 9

Introduction
1.5 Further Information
10 SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

Safety notes 2
2.1 General safety instructions
CAUTION
Correct, reliable operation of the product requires proper transport, storage, positioning and
assembly as well as careful operation and maintenance.
Only qualified personnel should install or operate this instrument.
Note
Alterations to the product, including opening or improper modifications of the product are not
permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.
2.2 Laws and directives
General requirements
Installation of the equipment must comply with national regulations. For example EN 60079-14
for the European Community.
Instrument safety standards
The device has been tested at the factory, based on the safety requirements. In order to
maintain this condition over the expected life of the device, the requirements described in these
Operating Instructions must be observed.
Environmental conditions according to IEC61010-1:
● Indoor/Outdoor use
● Altitude up to 2000 m
● Maximum relative humidity 80% for temperatures up to 31°C (88 °F) decreasing linearly up
to 50% relative humidity from 40 °C (104 °F)
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 11

● Overvoltage category II
●Pollution degree 2
NOTICE
Material compatibility
Siemens Flow Instruments can provide assistance with the selection of wetted sensor
parts. However, the full responsibility for the selection rests with the customer and Siemens
Flow Instruments can take no responsibility for any failure due to material incompatibility.
CE marked equipment
The CE-mark symbolizes the compliance of the device with the following directives:
●EMC-directive 2004/108/EC
● Low voltage directive 2006/95/EC
● Pressure equipment directive (PED/DGRL) 97/23/EC
● ATEX Directive 94/9/EG
2.3 Installation in hazardous area
WARNING
Conditions for safe use
Equipment used in hazardous areas must be Ex-approved and marked accordingly. It is
required that the special conditions for safe use provided in the manual and in the Ex
certificate are followed!
WARNING
Suitable hazardous area approval
Make sure the hazardous area approval is suitable for the environment in which the device
will be installed.
WARNING
"Flameproof enclosure" type of protection
Only open devices with type of protection "Flameproof enclosure" in hazardous areas when
the power to the device is turned off, otherwise there is a risk of explosion.
Safety notes
2.3 Installation in hazardous area
12 SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

WARNING
Laying of cables
Cable for use in Zone 1 and 2 or 21 and 22 must satisfy the requirements for having a proof
voltage > 500 V AC applied between the conductor/ground, conductor/shield and shield/
ground.
Connect the devices that are operated in hazardous areas as per the stipulations applicable
in the country of operation, e.g. for Ex "d" and "nA", permanent cables must be laid
WARNING
Requirements for meters used with transmitter
With intrinsically safe circuits, use only certified meters appropriate for the transmitter.
If a non-conforming supply unit is used, the "fail-safe" type of protection will no longer be
effective and the approval certification will be invalid.
2.3.1 ATEX 2 GD approval
The device is approved for use in hazardous area and has certificate Sira 11ATEX2124X.
Remote transmitter version:
II 2(1) GD
EX d e [ia] ia IIC T6 Gb
Ex tD A21 IP67 T85 °C
Ta -25 °C to 60 °C
Note
Markings for remote version only
These markings are for the Remote version only; the marking applicable to the Compact
versions depend upon their construction. See the latest issues of certificates Sira
07ATEX3181X, Sira 07ATEX1182X and Sira 03ATEX3339X.
Safety notes
2.3 Installation in hazardous area
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 13

*
Compact transmitter version:
● Ex d e [ia] ia IIC T3-T6 Gb
Ex tD A21 IP67 T** °C (** pipe temperature +13K, but not less than T85 °C
(MAG 3100 / MAG 3100 P)
● Ex d e [ia] ia IIB T3-T6 Gb
Ex tD A21 IP67 T** °C (** pipe temperature +18K, but not less than T85 °C
(MAG 1100 / MAG 1100 F)
*YHUBQQ
For sensors:
Refer to sensor certificates:
MAG 3100 / MAG 3100 P: Sira 07ATEX1182X (DN 15-DN300); Sira 03ATEX3339X (DN350-
DN2000)
MAG 1100 / MAG 1100 F: Sira 07ATEX3181X
Safety parameters associated with the remote transmitter version
Table 2-1 Intrinsically safe data
Sensor electrode input (Terminals 0, 81, 82, 83, 84 - "ia circuits")
IIB IIC
UO30 V DC 30 V DC
IO6.1 mA 6.1 mA
CO560 nF 66 nF
LO1 H 0.96 H
PO45.5 mW 45.5 mW
Safety notes
2.3 Installation in hazardous area
14 SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

Sensor coil terminals Terminal type
85 and 86 "e"
Power supply:
Parameter MAG 6000 I Ex de
Supply 115 to 230 VAC or 18 to 30 VDC
Max. allowable supply voltage Um (according to
ATEX certificate)
264 V
Ambient temperature -20 to +60 °C (-4 to 140 °F)
Enclosure IP67 / NEMA 4X
WARNING
Fail-safe protection
With intrinsically safe circuits, use only certified meters appropriate for the transmitter.
If a non-conforming suuply unit is used, the "fail-safe" type of protection wil no longer be
effective and the approval certification will be invalid.
User I/O interface
Remote MAG 6000 I: Model 7ME693-2BA4/5
Compact:
MAG 6000 I with MAG 3100 series: Model 7ME63x0-xxxxx-xD/E
Passive current
(31, 32)
Active current
(31, 32)
Relay
(44, 45, 46)
Frequency/pulse
(56, 57)
Profi (FISCO)
(95, 96)
Digital input
(77, 78)
IIC IIB IIC IIC IIC IIC IIC
Ui28 V DC UO30 V DC 30 V DC Ui30 V DC Ui28 V DC Ui17.5 V DC Ui30 V DC
II100 mA IO87.8 mA 87.8 mA II200 mA II100 mA II380 mA II
CI19.7 nF CO557 nF 63 nF CI3.3 nF CI14.2 nF CI0 nF CI0 nF
LI36 µH LO18.4 mH 4.6 mH LI0 µH LI36 µH LI0 µH LI0 µH
PI0.7 W PO0.66 W 0.61 W PI1.2 W PI1.2 W PI5.32 W PI1.2 W
Safety notes
2.3 Installation in hazardous area
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 15

Special conditions for ATEX 2 GD
It is required that:
● The equipment is supplied with its current output (terminals 31 and 32) in "Passive mode
only".
●The external connections to terminals 85 and 86 shall comply with the following:
– The wire conductors shall have a cross-sectional area between 0.5 mm2 and 2.5 mm2.
– No more than one single or multiple strand wire conductor shall normally be connected
to each of the terminals. If multiple conductors are required, these shall be joined in a
suitable manner, e.g. two conductors into a single insulated crimped boot lace ferrule.
– The insulation on the wire conductors shall extend to within 1 mm of the metal of the
terminal throat.
– The terminal screws shall be tightened down with a torque between 0.4 Nm and 0.45
Nm.
● The equipment shall not be opened when an explosive gas or dust atmosphere may be
present.
● The equipment internal circuits at the following terminals are not capable of withstanding
a 500 V r.m.s. a.c. test to earth as required by clause 6.3.12 of EN 60079-11-2007. This
must be taken into account in any equipment installation:
Terminals 77 and 78 – Digital input.
Terminals 95 and 96 – Foundation Fieldbus/Profibus (FISCO). (Not applicable to Model
7ME693-2BA6)
Terminals 0, 81, 82, 83 and 84 – Sensor electrode input (Remote Version only).
● electrical connections are in accordance with national requirements for installation of
electrical systems in hazardous areas, e.g. EN60079-14 in Europe.
● the protective cover for the power terminals is properly installed.
When the device is de-energized, the power supply terminal room may be opened because
the non-intrinsically safe power terminals are separately covered. Only remove protective
cover when device is de-energized.
● sensor and transmitter are connected to the potential equalizing conductor.
● when protective earth (PE) is connected, no potential difference between the protective
earth (PE) and the potential equalization (PA) can exist, even during a fault condition.
Safety notes
2.3 Installation in hazardous area
16 SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

2.3.2 FM/CSA Class I, Zone 1 approval
Compact and remote versions
*YHUBQQ
*
FM: Class I, Zone 1 IIC
CSA: Class I, Zone 1 IIC, Zone 21
User I/O interface
Remote MAG 6000 I: Model 7ME693-2BA4/5
Compact:
MAG 6000 I with MAG 1100: Model 7ME6110-xxx2x-xD/E
MAG 6000 I with MAG 1100 F: Model 7ME6140-xxx2x-xD/E
MAG 6000 I with MAG 3100 series: Model 7ME63x0-xxxxx-xD/E
Passive current
(31, 32)
Active current
(31, 32)
Relay
(44, 45, 46)
Frequency/pulse
(56, 57)
Profi (FISCO)
(95, 96)
Digital input
(77, 78)
IIB/IIC IIB IIC IIB/IIC IIB/IIC IIB/IIC IIB/IIC
Ui28 V DC UO30 V DC 30 V DC Ui30 V DC Ui28 V DC Ui17.5 V DC Ui30 V DC
II100 mA IO87.8 mA 87.8 mA II200 mA II100 mA II380 mA II
CI19.7 nF CO557 nF 63 nF CI7.5 nF CI14.2 nF CI0 nF CI0 nF
LI36 µH LO18.4 mH 4.6 mH LI0 µH LI36 µH LI0 µH LI0 µH
PI0.7 W PO0.66 W 0.61 W PI1.2 W PI1.2 W PI5.32 W PI1.2 W
Safety notes
2.3 Installation in hazardous area
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 17

2.3.3 FM Class I, II, III, Div 1 approval
Compact version for MAG 3100/3100 P sensors DN 15 to 300 (½" to 12")
*YHUBQQ
Hazardous area
Class I, Div. 1, Group A, B, C, D
User I/O interface
Passive current
(31, 32)
Active current
(31, 32)
Relay
(44, 45, 46)
Frequency/pulse
(56, 57)
Profi (FISCO)
(95, 96)
Digital input
(77, 78)
ABCD CD AB ABCD ABCD ABCD ABCD
Ui28 V DC UO30 V DC 30 V DC Ui30 V DC Ui28 V DC Ui17.5 V DC Ui30 V DC
II100 mA IO87.8 mA 86.8 mA II200 mA II100 mA II380 mA II
CI19.7 nF CO557 nF 63 nF CI3.3 nF CI14.2 nF CI0 nF CI0 nF
LI36 µH LO18.4 mH 4.6 mH LI0 µH LI36 µH LI0 µH LI0 µH
PI0.7 W PO0.66 W 0.66 W PI1.2 W PI1.2 W PI5.32 W PI1.2 W
Notes from control drawing
1. The non-intrinsically safe terminals (power rail) must not be connected to a device which
uses or generates more than 250/30 Vrms or DC.
2. The installation must meet the requirements of the National Electrical Code/Canadian
Electrical Code.
3. Conduit seal is required within 460 mm (18") from MAG 6000 I in hazardous areas (Class
I, Div. 1).
The control drawings are found on the CD-ROM shipped with the device and on the Siemens
homepage at http://www.siemens.com/flowdocumentation.
See also
Control drawing (Page 97)
Safety notes
2.3 Installation in hazardous area
18 SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH

Description 3
3.1 Applications
The pulsed DC-powered magnetic flowmeters are suitable for measuring the flow of almost all
electrically conductive liquids, pastes, and slurries with max. 40% solids.
The main applications can be found in the following sectors:
● Water and waste water
● Chemical and pharmaceutical industries
● Food & beverage industry
● Mining and cements industries
● Pulp and paper industry
● Steel industry
● Power generation; utility and chilled water industry
WARNING
This is a Class A product
In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
3.2 System components
The SITRANS F M flowmeter system includes:
● Transmitter (types: MAG 6000 I standard or Ex version in compact or remote configuration)
● Sensor (types: SITRANS F M MAG 1100/1100 HT/1100F, MAG 5100 W, MAG 3100 P/
3100 or 3100 HT)
● Communication module (optional) (types: HART, PROFIBUS PA/DP, MODBUS RTU
RS485, Foundation Fieldbus H1, Devicenet)
Communication solutions
The SITRANS F M platform enables fitting of add-on bus modules without loss of analog, pulse
and relay outputs, and all modules can be fitted as true Plug & Play.
Standard transmitter:
● HART
● PROFIBUS PA and DP
SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH 19

● Foundation Fieldbus H1
●MODBUS RTU RS485
● Devicenet
Ex-transmitter:
● HART
● PROFIBUS PA
● Foundation Fieldbus H1
3.3 Design
The SITRANS F M MAG 6000 I/MAG 6000 I Ex de transmitter is designed for demands in the
process industry. The robust cast aluminum housing provides superb protection, even in the
most harsh industrial environments. Full input and output functionality is given even in the Ex
version.
Compact version Remote version
The transmitter is designed for either compact or remote installation in non-hazardous or
hazardous areas.
Functions:
●Flow rate measurement
● 2 measuring ranges
● Display with 2 totalizers and keypad
● Low flow cut-off
● Analog, pulse/frequence and relay outputs
● Optional: additional digital communication modules
● Error and error log system
● Uni-/bidirectional flow
● Limit switches
● Integrated batch control
Description
3.3 Design
20 SITRANS MAG 6000 I/6000 I Ex de
Operating Instructions, 08/2018, A5E02083319-AH