Siemens SITRANS F User manual

SITRANS F
Ultrasonic flowmeters
SITRANS FUS380/FUE380
Operating Instructions
7ME340 (FUS380)
7ME341 (FUE380)
05/2018
A5E00730100-AE
Introduction 1
Safety notes 2
Description 3
Installing/Mounting 4
Connecting 5
Commissioning 6
Functions 7
Service and maintenance 8
Troubleshooting/FAQs 9
Technical data 10
Parameter lists A
Settings B
Appendix A C

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E00730100
Ⓟ 01/2019 Subject to change
Copyright © Siemens AG 2018.
All rights reserved

Table of contents
1 Introduction...................................................................................................................................................7
1.1 Document History.....................................................................................................................7
1.2 Items supplied ..........................................................................................................................7
1.3 Checking the consignment.......................................................................................................8
1.4 Device identification .................................................................................................................9
1.5 Further Information.................................................................................................................12
1.6 Security information ...............................................................................................................12
1.7 Transportation and storage ....................................................................................................13
1.8 Notes on warranty ..................................................................................................................13
2 Safety notes................................................................................................................................................15
2.1 General safety instructions.....................................................................................................15
2.2 Manufacturer's design and safety statement..........................................................................15
2.3 Safety note for bronze sensors ..............................................................................................16
2.4 Conformity with European directives......................................................................................16
2.5 Lithium batteries.....................................................................................................................17
2.6 Installation in hazardous area ................................................................................................17
3 Description..................................................................................................................................................19
3.1 Overview ................................................................................................................................19
3.2 System components...............................................................................................................19
3.3 Design ....................................................................................................................................20
3.4 Features .................................................................................................................................20
3.5 Principle of operation .............................................................................................................21
4 Installing/Mounting......................................................................................................................................23
4.1 Flowmeter installation ............................................................................................................23
4.2 Sensor installation..................................................................................................................23
4.2.1 Inlet/outlet conditions .............................................................................................................23
4.2.2 Reduction ...............................................................................................................................27
4.2.3 Insulation................................................................................................................................28
4.3 Transmitter installation (compact/remote versions) ...............................................................29
4.3.1 Installation wall mounting kit (remote transmitter)..................................................................30
5 Connecting .................................................................................................................................................31
5.1 Mains-powered transmitter.....................................................................................................31
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 3

5.2 Battery-powered transmitter...................................................................................................32
5.3 Compact system ....................................................................................................................32
5.3.1 Connecting battery (battery-powered versions and mains-powered versions with back-
up battery) ..............................................................................................................................33
5.3.2 Connecting Siemens sensor link cable ..................................................................................33
5.3.3 Connecting power supply cable (main-powered systems only) .............................................34
5.3.4 Connecting pulse output signal cable(s) ................................................................................35
5.3.5 Finishing connection ..............................................................................................................37
5.4 Remote system ......................................................................................................................37
5.4.1 Sensor side ............................................................................................................................38
5.4.1.1 Connecting Siemens sensor link cable ..................................................................................38
5.4.1.2 Finishing connection ..............................................................................................................38
5.4.2 Transmitter Side.....................................................................................................................39
5.4.2.1 Connecting battery (battery-powered versions and mains-powered versions with back-
up battery) ..............................................................................................................................39
5.4.2.2 Connecting Siemens sensor link cable ..................................................................................39
5.4.2.3 Connecting power supply cable (main-powered systems only) .............................................40
5.4.2.4 Connecting pulse output signal cable(s) ................................................................................41
5.4.2.5 Finishing connection ..............................................................................................................43
5.5 Optional current output module..............................................................................................43
5.5.1 Installing and connecting optional current output module ......................................................44
5.5.2 Connecting .............................................................................................................................45
5.5.3 Finishing connection ..............................................................................................................46
5.6 Wiring energy calculator.........................................................................................................46
5.7 Sealing of FUE380 .................................................................................................................47
5.7.1 User sealing ...........................................................................................................................47
5.7.2 Verification sealing .................................................................................................................47
6 Commissioning ...........................................................................................................................................49
6.1 Introduction ............................................................................................................................49
6.2 Operating the local display.....................................................................................................49
6.3 Navigating the menu structure ...............................................................................................50
6.4 Start-up routine ......................................................................................................................51
6.5 Commissioning via PDM ........................................................................................................52
6.5.1 Installing and connecting the IrDA interface adapter .............................................................53
6.5.2 Installing the device driver......................................................................................................54
6.5.3 Adding the device to the network ...........................................................................................56
6.5.4 Configuring the device ...........................................................................................................57
6.5.5 Optimizing the system............................................................................................................58
6.5.6 Output A, terminals 56/57: .....................................................................................................60
6.5.7 Output B, terminals 66/67: .....................................................................................................61
6.5.8 Optional current output, terminals 31/32 ................................................................................61
6.5.9 Checking the operation readiness..........................................................................................63
7 Functions ....................................................................................................................................................65
7.1 Unit selection..........................................................................................................................65
7.2 Number of decimal digits........................................................................................................66
Table of contents
SITRANS FUS380/FUE380
4Operating Instructions, 05/2018, A5E00730100-AE

7.3 Password-protected data .......................................................................................................66
7.4 Hardware key .........................................................................................................................66
8 Service and maintenance ...........................................................................................................................69
8.1 Maintenance...........................................................................................................................69
8.2 Battery replacement ...............................................................................................................69
8.3 Service menu .........................................................................................................................72
8.4 Technical support...................................................................................................................73
8.5 Application-specific data - Qualification certificate .................................................................74
8.6 Return procedures .................................................................................................................79
8.7 Battery disposal......................................................................................................................80
9 Troubleshooting/FAQs................................................................................................................................81
9.1 Error codes.............................................................................................................................81
9.2 Diagnosing with PDM.............................................................................................................82
10 Technical data ............................................................................................................................................87
10.1 Accuracy ................................................................................................................................87
10.2 FUS380 and FUE380 systems...............................................................................................88
10.3 Optional current output module..............................................................................................89
10.4 Output characteristics ............................................................................................................90
10.5 Battery....................................................................................................................................92
10.6 Sensor for FUS380 and FUE380 ...........................................................................................93
10.7 Dimensional drawings for FUS380 and FUE380 ...................................................................94
10.8 Sensor dimensions for FUS380 and FUE 380 .......................................................................94
A Parameter lists............................................................................................................................................97
A.1 Identification ...........................................................................................................................97
A.2 Output ....................................................................................................................................98
A.3 Diagnostics...........................................................................................................................101
A.4 Meter setup ..........................................................................................................................106
A.5 Human Interface...................................................................................................................108
A.6 Unit conversion table............................................................................................................108
B Settings.....................................................................................................................................................111
B.1 Factory settings....................................................................................................................111
B.2 Factory settings for Modbus communication........................................................................112
B.3 Ordering of spare parts ........................................................................................................113
C Appendix A ...............................................................................................................................................115
C.1 Technical support.................................................................................................................115
Table of contents
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 5

C.2 Certificates ...........................................................................................................................115
Index.........................................................................................................................................................117
Table of contents
SITRANS FUS380/FUE380
6Operating Instructions, 05/2018, A5E00730100-AE

Introduction 1
These instructions contain all information required to commission and use the device. Read the
instructions carefully prior to installation and commissioning. In order to use the device
correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
1.1 Document History
The following table shows the most important changes in the documentation compared to each
previous edition.
Edition Remarks FW version EDD version
05/2018 ● Restructure this document
● Updates in transmitter and sensor
connection
● Adding current output option module
● Adding Accuracy to Technical Data
● Responsibility transfer to Siemens AG
2.04 1.02.09
09/2016 ● Restructure this document
● Updates for SIMATIC PDM 8.2
2.03 1.02.08-01
09/2013 ● Restructure this document
● Adding transmitter information
2.03 1.02.07
09/2011 Update with FW 2.03 2.03 1.02.07
10/2010 Update with FW 1.05 1.05 1.01.04
12/2009 Update with FW 1.04 1.04 1.01.04
2003 First edition with product release 1.02 1.01.04
The FUS080 is configured in a combination of hardware (HW) and firmware (FW). For
communication and parametrization via SIMATIC PDM the correct version of the EDD driver for
FUS/FUE 380 is needed. The various relations are listed above.
1.2 Items supplied
The device can be delivered as either a compact or a remote system.
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 7

Compact system
● Sensor SITRANS FUS300
● Transmitter SITRANS FUS080 or FUE080
● Connection PCB
● DVD with documentation and cerificates
● Safety note
● Calibration report
● Short Siemens sensor link cable
● Connection accessories
mnnmnmn
nmmnnmmnmnnmnmn
nmmnnmmnmnnmnmn
mnmnnmnmn
nnmnmn
mnnmnmnn
mnnmnmn
mnnmnmnn
mnmnn
mnnmnn
6766 57 56
Safety Note
Cal. rep.
Remote system
● Sensor SITRANS FUS300
● Transmitter SITRANS FUS080 or FUE080
● Connection PCB
● DVD with documentation and cerificates
● Safety note
● Calibration report
● Mounting kit with bracket and terminal box
● Long Siemens sensor link cable
● Connection accessories
mnnmnmn
nmmnnmmnmnnmnmn
nmmnnmmnmnnmnmn
mnmnnmnmn
nnmnmn
mnnmnmnn
mnnmnmn
mnnmnmnn
mnmnn
mnnmnn
6766 57 56
Safety Note
Cal. rep.
Note
Scope of delivery may vary, depending on version and add-ons. Make sure the scope of
delivery and the information on the nameplate correspond to your order and the delivery note.
1.3 Checking the consignment
1. Check the packaging and the delivered items for visible damages.
2. Report any claims for damages immediately to the shipping company.
Introduction
1.3 Checking the consignment
SITRANS FUS380/FUE380
8Operating Instructions, 05/2018, A5E00730100-AE

3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
● Do not use damaged or incomplete devices.
1.4 Device identification
The FUS380 or FUE380 flowmeter is delivered with different labels (nameplates) on the
transmitter and sensor. The transmitter and sensor are matched paired.
The transmitter has two nameplates. One (silver) is placed on the front of the transmitter. The
transmitter system nameplate (white) is placed on the right side of the transmitter. Both provide
valuable information about the device and system. The sensor has one nameplate. The sensor
system nameplate (white) is placed on the middle of the sensor.
Note
Identification
Identify your device by comparing your ordering data with the information on the product and
specification nameplates.
Introduction
1.4 Device identification
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 9

Transmitter system nameplate
6,75$16)8(
6\ᚔHP1R6HULDO1R7UDQVPLWWHU6HULDO1R6HQVRUTVPKTSTLPK&DEOHOHQJWK&DO)DFWRU7DPE6:+:9&KHFNVXP):&HUWLᚏFDWLRQ1R$FFXUDF\&ODVV(QYLURQPHQWDO&ODVV(0[[[[[[[[[[[[[[[[[[[[P[[[[r&WRr&'.0,[[[[3XOVHYDOXHOS3XOVHZLGWKPV<HDURI0DQXI
6LHPHQV$*'(.DUOVUXKH0DGHLQ)UDQFH
M18 0200

①Manufacturer
②Product type
③System number and system serial number
④Transmitter number and serial number
⑤Sensor number and serial number
⑥Maximum flow value (qs), Nominal flow value (qp), Minimum flow value (qi)
⑦Cable length (empty for compact version)
⑧Calibration factor
⑨Ambient temperature range
⑩Software version/Hardware version
⑪Checksum firmware number
⑫Type approval number (shown on FUE380 versions only)
⑬Accuracy class (shown on FUE380 versions only)
⑭Environmental class (shown on FUE380 versions only)
⑮Verification markings (shown on MID-verified FUE380 versions only)
⑯Pulse value (output A)
⑰Pulse width (output A)
⑱Year of manufacture
⑲Conformity with country-specific directives
Figure 1-1 Transmitter system nameplate, FUE380 example
Introduction
1.4 Device identification
SITRANS FUS380/FUE380
10 Operating Instructions, 05/2018, A5E00730100-AE

Sensor system nameplate
SITRANS FUE380
Sensor:
Serial No.:
Dimension:
Process Con.:
qs:
qp / qi:
Θmin to Θmax:
Cal. Factor:
T-amb.:
MAWP (PS) at ...
°C (TS):
MAWP (PS) at ... °C (TS):
Fluid group:
xxxx....
xxxx....
DN...
xxxx....
...m3/h
.../... m3/h
+15 °C to +200°C
xxxx....
-10 to +55 °C
....bar
....bar
.../...
SYSTEM No.
Serial No.:
Year of Manuf.:
Meter orientation:
xxxx....
xxxx....
2018
Horizontal
0200
M18
Siemens AG, DE-76181 Karlsruhe
Made in France
Accuracy Class: 2
Certification No.: DK-0200-MI004-005
Environmental Class: E2, M1

①Manufacturer
②Product type
③Sensor number and serial number
④Dimension (nominal size ordered)
⑤Process connections
⑥Maximum flow value (qs), Nominal flow value (qp), Minimum flow value (qi)
⑦Water temperature range
⑧Calibration factor
⑨Ambient temperature range
⑩Maximum allowable working pressures at 15 °C (59 °F) and 200°C (392 °F) (max. tempera‐
ture (TS))
⑪Fluid group
⑫System number and system serial number
⑬Year of manufacture
⑭Meter orientation
⑮Type approval number (shown on FUE380 versions only)
⑯Accuracy class (shown on FUE380 versions only)
⑰Environmental class (shown on FUE380 versions only)
⑱Conformity with country-specific directives
⑲Verification and PED markings (verification marking shown on MID-verified FUE380 versions
only)
Figure 1-2 Sensor system nameplate, FUE380 example
Note
The matched paired transmitter and sensor shall be mounted together
At installation, please check that the system nameplates of transmitter and sensor have the
same system serial number.
Introduction
1.4 Device identification
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 11

1.5 Further Information
Product information on the Internet
The Operating Instructions are available on the documentation disk shipped with the device,
and on the Internet on the Siemens homepage, where further information on the range of
SITRANS F flowmeters may also be found:
Product information on the internet (http://www.siemens.com/flow)
Worldwide contact person
If you need more information or have particular problems not covered sufficiently by these
Operating Instructions, get in touch with your contact person. You can find contact information
for your local contact person on the Internet:
Local contact person (http://www.automation.siemens.com/partner)
1.6 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines and
networks. Systems, machines and components should only be connected to the enterprise
network or the internet if and to the extent necessary and with appropriate security measures
(e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. You can find more information about industrial security by visiting:
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends you apply product updates as soon as available and always
use the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity.
Introduction
1.6 Security information
SITRANS FUS380/FUE380
12 Operating Instructions, 05/2018, A5E00730100-AE

1.7 Transportation and storage
To guarantee sufficient protection during transport and storage, observe the following:
● Keep the original packaging for subsequent transportation.
● Devices/replacement parts should be returned in their original packaging.
● If the original packaging is no longer available, ensure that all shipments are properly
packaged to provide sufficient protection during transport. Siemens cannot assume liability
for any costs associated with transportation damages.
NOTICE
Insufficient protection during storage
The packaging only provides limited protection against moisture and infiltration.
● Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in Technical data
(Page 87).
1.8 Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing agreement,
commitment or legal relationship. The sales contract contains all obligations on the part of
Siemens as well as the complete and solely applicable warranty conditions. Any statements
regarding device versions described in the manual do not create new warranties or modify the
existing warranty.
The content reflects the technical status at the time of publishing. Siemens reserves the right
to make technical changes in the course of further development.
Introduction
1.8 Notes on warranty
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 13

Introduction
1.8 Notes on warranty
SITRANS FUS380/FUE380
14 Operating Instructions, 05/2018, A5E00730100-AE

Safety notes 2
2.1 General safety instructions
CAUTION
Correct, reliable operation of the product requires proper transport, storage, positioning and
assembly as well as careful operation and maintenance.
Only qualified personnel should install or operate this instrument.
Note
Alterations to the product, including opening or improper modifications of the product are not
permitted.
If this requirement is not observed, the CE mark and the manufacturer's warranty will expire.
2.2 Manufacturer's design and safety statement
● Responsibility for the choice of flowmeter pipe material as regards abrasion and corrosion
resistance lies with the purchaser. The effect of any change in process medium during
operation of the meter should be taken into account. Incorrect selection of flowmeter pipe
material could lead to failure of the flowmeter.
● Stresses and loading caused by earthquakes, traffic, high winds and fire damage are not
taken into account during flowmeter design.
● Do not install the flowmeter such that it acts as a focus for pipeline stresses. External loading
is not taken into account during flowmeter design.
● Please be aware of the risk of installing the sensor in a highly vibrating environment. Parts
may shake loose and the complete system must be monitored in that case.
● Flanges and joints as well as related pressure/temperature (p/t) classification has been
described in EN 1092-1. See ferrite steel group 1E1: table 15.
● During operation do not exceed the pressure and/or temperature ratings indicated on the
data label or in these operating instructions.
● It is recommended that all installations include an appropriate safety valve and adequate
means for draining.
● Under the „Pressure Equipment Directive" (PED), this product is a presssure accessory and
not approved for use as a safety accessory, as defined by the PED.
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 15

Environmental conditions according MID (Directive 2014/32/EU)
● Environment class: E2 (electromagnetic), M1 (mechanical)
● Climatic class: -10°C - +55°C, condensing, closed
2.3 Safety note for bronze sensors
WARNING
Hot water or steam
Potential risk of burns.
Do NOT unscrew bronze sensor during operation (DN 50 to DN 80).
2.4 Conformity with European directives
The CE marking on the device symbolizes the conformity with the following European
directives:
Electromagnetic compatibili‐
ty EMC
2014/30/EU
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to elec‐
tromagnetic compatibility
Low voltage directive LVD
2014/35/EU
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to the
making available on the market of electrical equipment designed
for use within certain voltage limits
Pressure equipment direc‐
tive PED
2014/68/EU
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to the
making available on the market of pressure equipment
Radio equipment directive
RED
2014/53/EU
Directive of the European Parliament and of the Council on the
harmonisation of the laws of the Member States relating to the
making available on the market of radio equipment and repealing
Directive 1999/5/EC
Measuring instruments direc‐
tive MID
2014/32/EU
Directive of the European Parliament and the Council on the har‐
monisation of the laws of the Member States relating to the mak‐
ing available on the market of measuring instruments
Restriction of Hazardous
Substances RoHS
2011/65/EU
Directive of the European Parliament and the Council on the re‐
striction of the use of certain hazardous substances in electrical
and electronic equipment
The applicable directives can be found in the EU declaration of conformity of the specific device.
Safety notes
2.4 Conformity with European directives
SITRANS FUS380/FUE380
16 Operating Instructions, 05/2018, A5E00730100-AE

2.5 Lithium batteries
Lithium batteries are primary power sources with high energy content designed to provide the
highest possible degree of safety.
WARNING
Potential hazard
Lithium batteries may present a potential hazard if they are abused electrically or
mechanically. Observe the following precautions when handling and using lithium batteries:
● Do not short-circuit, recharge or connect with false polarity.
● Do not expose to temperatures beyond the specified temperature range.
● Do not incinerate.
● Do not crush, puncture or open cells or disassemble.
● Do not weld or solder to the battery’s body.
● Do not expose contents to water.
2.6 Installation in hazardous area
WARNING
NOT allowed for use in hazardous areas!
Equipment used in hazardous areas must be Ex-approved and marked accordingly!
This device is NOT approved for use in hazardous areas!
WARNING
500 V insulation test
The device is not capable of withstanding the 500 V insulation test required by Clause 6.3.12
of EN60079-11. This must be taken into account when installing the device.
Safety notes
2.6 Installation in hazardous area
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 17

Safety notes
2.6 Installation in hazardous area
SITRANS FUS380/FUE380
18 Operating Instructions, 05/2018, A5E00730100-AE

Description 3
3.1 Overview
The SITRANS F US ultrasonic flowmeter systems consist of a sensor and a transmitter. This
system consists of sensor type FUS300 or SONOKIT and the transmitters type FUS080 or
FUE080. The transmitter type FUS080 is for the standard flowmeter series SITRANS FUS380
or SONOKIT series. The transmitter type FUE080 is for the type-approved flowmeter series
SITRANS FUE380 with the custody transfer approval for use in energy metering systems. The
transmitters are designed to measure flow in water applications.
The ultrasonic flowmeter transmitter comes as battery or mains-powered version.
The following table shows the ultrasonic flowmeter systems with these transmitter types:
Sensor type Transmitter Flowmeter system
FUS300 (2-path)
DN 50 – DN 1200
FUS080 FUS380 (2-path)
FUS300 (2-path)
DN 50 – DN 1200 (with custody transfer approval
for use with heatmeters)
FUE080 FUE380 (2-path)
SONOKIT (1- or 2-path)
DN 100 – DN 1200
FUS080 SONOKIT (1-path / 2-path)
These Operating Instructions are only for the FUS380 and FUE380 flowmeter systems. The
FUS080 for SONOKIT and the SONOKIT sensors have separate Operating Instructions.
3.2 System components
The flowmeter system includes:
● Battery or mains-powered transmitter (FUS080 or FUE080)
● Sensor FUS300 as 2-path inline sensor with flanges, wet-calibrated from factory together
with the transmitter (DN 50 (2") to DN 1200 (48"))
or the retrofitting set SONOKIT (1-path for pipe diameters from DN 100 (4") up to DN 1200
(48") or for 2-path from DN 200 (8") up to DN 1200 (48")).
SITRANS FUS380/FUE380
Operating Instructions, 05/2018, A5E00730100-AE 19

3.3 Design
The transmitter type SITRANS FUS080 is designed with fiberglass reinforced polyamide
enclosure for remote or compact installation in normal areas. The remote versions are available
with up to 30 meter distance from flowmeter to transmitter. In the FUS380 and FUE380 series
the sensor cables are already mounted at the sensor.
SITRANS FUS080 transmitter SITRANS FUS080 display
The transmitter is available in an IP67/NEMA 4X/6 enclosure and is designed for use in the
flowmeters series:
● SONOKIT (1-path or 2-path)
● FUS380 (2-path)
● FUE380 (2-path)
For spare part cases the transmitter is always ordered as part of a complete flowmeter system,
it can be ordered preprogrammed with the given sensor data (system serial number).
3.4 Features
The following features are available:
● Battery or mains-powered transmitter
● Battery-powered with 3.6 V Lithium dual D-cell batteries
● Suitable for sensor pipe diameters from DN 50 (2") up to DN 1200 (48")
● IP67 (NEMA 4X/6) rated polyamid transmitter enclosure
● Factory preset to the nominal dimensions of pipe type and pipe size
● Programming via SIMATIC PDM
● Local control panel with single push button, 8-digit display and IrDA optical interface for
communication with SIMATIC PDM
● Display showing accumulated volume as well as instantaneous flow rate. The displayed
units are m3 and m3/h
● Two digital outputs for volume pulse or alarm
● 4-20 mA output (optional)
Description
3.4 Features
SITRANS FUS380/FUE380
20 Operating Instructions, 05/2018, A5E00730100-AE