Siemens PELTON & CRANE Light Fantastic II User manual

PELTON& CRANE
Light Fantastic ||
Installation Instructions

9
Safety Warnings
A CAUTION
Caution messages appear before procedures which, if
not observed, could result in damage to equipment.
AWARNING
Warning messages alert you to a specific procedure or
practice which, if not followed correctly, could cause
personal injury or damage to equipment.
À DANGER
Danger messages alert you to a specific procedure or
practice which, if not followed correctly, could cause
serious personal injury.
List of Contents
LFII (Unit Mount) Installation ...................... 2
LFTII (Track Light) Installation ...............,..... 4
LFTI-D (Dual Track) Installation .................. 10
LFCII (Column Light) Installation ................. 11
LFCII-D (Dual Column Light) Installation ......... 15
LFWII (Wall Light) Installation .................... 16
LFLII (Laboratory Light) Installation ............... 17
LFII Autoclavable Handles (All Models) .......... 18
οσοι νο ο ο a πο τας 19

JAA CAUTION
All
wiring
must
be
performed
by
a
licensed
electrician.
Because
of
varying
city
electrical
codes,
the
dealer
should ensure
that
instal-
lation
will
meet
local
requirements.
Pelton
&
Crane
cannot
be
responsible
for
an
installa-
tion
which
does
not
meet
local
electrical
codes.
The
Light
Fantastic
Il
is
available
in
a
variety
of
models.
Identify
the
particular
model
for
your
installation
application
and
install
the
following
instruction
for
the
specific
unit
as
outlined.
NOTE:
For
maximum
operating
versatility
of
the
LFII,
install
rear
arm
60”
(152.4
cm)
from
the
floor.
LFII
(UNIT
MOUNT)
INSTALLATION
Holding
LFII
in
position
over
mounting
column,
route
LFII
power
supply
cord
through
column.
Insert
male
electrical
plug
in
grounded
recep-
tacle
on
unit
(1.6
amp,
120
VAC,
60
Hz).
Protect
circuit
with
a
15
amp
fuse
or
circuit
breaker.
Apply
light
application
of
petrolatum
or
oil
to
outer
surface
of
bushing
before
inserting
into
the
mounting
column.
Insert
rear
arm
bushing
in
column.
AA CAUTION
Failure to apply lubricant may cause bush-
ing to bind in tube and unscrew itself from
rear arm of light.
Ensure column is plumb to prevent light from
drifting.
niversal ion (For Right or Left-
Han ration
1. The LFIl includes a universal arm adapter
which may be right or left-hand positioned.
All lights shipped from the factory are posi-
tioned for right-handed operation. Should
the doctor need a left-handed light, remove
the screw A adjacent to the rear arm/arm
adapter joint B. Rotate arm adapter until
other arm adapter hole aligns with rear arm
hole. Reinsert and tighten screw.
Optional Wall Mounting Bracket For Unit Light
2. An optional wall mounting bracket (006719)
or wall mounting bracket and plate assembly
(011203) are available (when required) to
mount unit light to wall.
NOTE: Wall mounting bracket (006719) is
not recommended for dry wall installa-
tion. Order 011203 for dry wall installa-
tion.

install wall mounting bracket (006719) as follows
1. Position bottom edge of bracket A 54”
(137.2 cm) from floor. (Height may vary for
individual requirements.)
Position wall mounting bracket with bottom
center located within 30” (76.2 cm) of an
electrical outlet (1.6 amp, 120 VAC, 60 Hz).
As an alternative, the wall mounting bracket
has a recess for mounting directly over a
duplex outlet if located 54” (137.2 cm)
above the finished floor surface.
2. Secure wall mounting bracket to wall with
screws entering solid wood at least 2”
(5.1 cm). Framing behind wall must be
secure.
Route power supply cord from light through
wall mounting bracket hole and plug into
electrical outlet.
Apply light application of petrolatum or oil to
outer surface of bushing before inserting
into the wall mounting bracket. Insert rear
arm bushing in wall mounting bracket.
Ensure wall mounting bracket is plumb to
| prevent light from drifting.
A | wall mounting bracket | ssembl
1 /3 (011203) as follows
3. Position bottom edge of plate 56" (142.2
cm) from floor. (Height may vary for individ-
ual requirements.)
Secure plate to vertical stud in wall (near
wall receptacle) with three #24 x 2-1/2”
long minimum wood screws.
4. Fasten wall mounting bracket to plate with
four
1/4”—20 screws.
Apply light application of petrolatum or oil to
outer surface of bushing before inserting
into the wall mounting bracket. Insert rear
arm bushing in wall mounting bracket.
Ensure wall mounting bracket and plate
assembly is plumb to prevent light from drift-
ing.

1
LFTII
(TRACK
LIGHT)
INSTALLATION
*
ji
Pre-Installation
of
Electrical
Wiring
—
Il
№
2
:
1.
Stub
out
a
2.0
amp,
120
VAC,
60
Hz
electri-
에
cal supply for the LFTII or a 4.0 amp, 120
VAC, 60 Hz line for the LFTII-D. See posi-
プー
A
|
tion
of
transformer
box
A.
Protect
circuit
with
a 15 amp fuse or circuit breaker.
| 8'0" (2.44 m) 2. Stub out wiring 39-5/8” (100.6 cm) from
MIN.
the
chair
center
line
along
the
longitudinal
|
13°
(3.96
m)
axis
of
the
LFTII
track
B
and
trolley
C
MAX. assembly.
NOTE:For electrical supply connection,
use wiring suitable for at least 90°C
(194*F).
6'6" 1.98 m)+ NOTE: The maximum height the LFTII
3"
(7.6
cm)
may
be
mounted
is
13'(3.96
m).
However,
Pelton & Crane does not recommend any
mounting in excess of 10’(3.05 m).
3. Ensure green ground wire D is grounded at
・ ground screw E.
4. Install wall switch between power supply
WHITE and transformer. This provides for safety
and convenience during installation or ser-
BLACK vice. Wall switch can be switched off during
electrical storms to prevent transformer
damage caused by voltage overloads. Wire
A nuts F are not furnished.
4 F GREEN B
BLACK
FUSE

bh:
11.
LB
|
LFTII
(TRACK
LIGHT)
INSTALLATION,
continued
Mounting
Track
And
Trolley
—
LFTII
5.
The
LFTII
track
and
trolley
are
shipped
com-
pletely
assembled.
The
track
channel
A
and
transformer
B
are
mounted
to
a
plywood
pallet
C.
Two
dress
covers
D,
two
side
pan-
els
E,
two
end
caps
F
and
a
light
trolley
G
are
attached
to
the
channel.
6.To
reach
the
four
17/64”
diameter
pre-
drilled
mounting
holes
H
in
the
plywood
pal-
let
C,
detach
the
two
end
caps
F
by
remov-
ing
two
#10
x
1/2”
round
head
slotted
machine
screws
|
from
each
end.
Set
end
Caps
and
screws
aside.
7.
Identify
the
four
17/64”
diameter
predrilled
mounting
holes
H
in
the
plywood
pallet
C.
8.
Remove
two
#8
x
3/4”
pan
head
slotted
sheet
metal
screws
J
from
each
side
panel.
Lift
away
side
panels.
Set
aside
with
screws.
9.
For
easier
installation,
detach
the
trolley
G
from
the
channel
before
mounting
the
pal-
let.
10.
Remove
two
stops
K
from
the
end
of
the
track
channel
opposite
the
transformer
box.
NOTE: Do NOT remove side stops L.
11.
Disconnect
power
cord M
at
trolley
bracket
leaving
cord
intact
under
dress
cover
D
and
power
cord
clamp
N.
Remove trolley and set aside.

10"
(25.4 cm)
64" (162.6 cm)
(PREDRILLED)
8-5/8"
(21.9 em)
60° MIN.
(152,4 cm)
(NEW HOLES)
67" MAX.
(170.2 cm)
1/4 DIA. x 47
LONG LAG SCREW
(NOT FURNISHED)
D
z
13.
/
C
Nu
i
mt 4
ii gg
|
Pr
| LI Ι 8-5/8"
60" (152.4 cm) (21.9 ст)
MIN.
67" (170.2 cm)
MAX.
mi 5
(152.4 cm)! ! 8-5/8"
MIN. (21.9 cm)
67" (170.2 cm) —2%|
MAX.
mee (NEW HOLES)
ea
1
2.
A
ο
EMBED SCREW AT (6.4 cm)
LEAST 2-1/2* (6.4 em) <|
INTO SOLID WOOD |
= \
ANNEE
17/64" (.57 cm) DIA. — HT
314º (1.9 em) — 2
LFTII (TRACK LIGHT) INSTALLATION,
continued
12. NOTE: Normally, further disassembly of the
track is not necessary for installation. If addi-
tional mounting fasteners are required, drill
and counterbore holes in plywood mounting
pallet A as shown.
Continue installation using one of the three mounting
situation instructions following.
Ensure ceiling substructure is firmly secured to
support approximately 200 pounds live load. Use
fasteners such as screws and bolts to secure the
substructure rather than fasteners such as nails
or glue.
13. Using four predrilled holes B in plywood pallet
(3/4” x10" x 76-13/16”) mount to perpendic-
ular wood joists C with four 1/4” x4" lag
screws D.
NOTE: Drill additional holes E if necessary.
Ensure pallet is level.
nti rall ists — Il
14. Install cross bracing F between the parallel joists
G as shown. Ensure ceiling substructure is firmly
secured to support approximately 200 pounds.
15. Using four predrilled holes H in plywood pallet
(3/4” x10” x 76-13/16”), mount to cross
bracing F with four 1/4” x4" lag screws D.
NOTE: Drill additional holes | on bracing
joists F if necessary.
Ensure pallet is level.

A16.
SS
ee en ee
C D
18.
E
Wh,
8-3/16"
(20.8 em) |
© OF CHAIR
LFTII
(TRACK
LIGHT)
INSTALLATION,
continued
Mounting
Pallet
to
Suspended
Ceiling
—
LFTII
16. Install joists A as shown.
17.
Install
wood
cross
bracing
B
flush
with
ceil-
ing
C.
NOTE: If alternate method of construc-
tion
is
required,
an
optional
Suspended
Ceiling
Kit
(001372)
is
available
from
Pel-
ton & Crane.
18.
install
subpallet
D
or
an
equivalent
brace
as
shown
using
nuts
E
and
washers
F.
19. Install plywood pallet using 3/4” O.D. flat
washers G and bolts H as shown and
ensure pallet is level.
Reattach track light components by reversing
instructions on page 5.
10° (25.4 ст) —
11/16"
(1.7 em) —
31" (78.7 cm)
33" (83.8 cm)
1
2" (5.1 cm) DIA. HOLE
De (FOR ELECTRICAL WIRING)
-一 5/16" (.79 cm) DIA. HOLES
8-5/8" (21.9 cm) APART TO
ACCEPT PLYWOOD PALLET
で
$
|
| 8-5/8" |
©
pe1-13/16"
(4.6 cm)
64" (162.6 cm) —————>]
1 39-3/16”. (99.5 em) —
76-13/16" (195.1 cm) —>

LFTII (TRACK LIGHT) INSTALLATION,
continued
Installation of Column — LETII
20. Route wiring from trolley through column.
21. Screw end of column securely in the trolley.
22. Insert and tighten two trolley set screws.
23. Place a piece of electrical tape around a
1/8" drill bit to mark depth to which pilot hole
is to be drilled.
24. Atter locating the 3/32” pilot hole in the trol-
ley, drill a 1/8” hole through trolley/column
assembly to a depth of 5/8”. Drive in roll pin
flush with outside of trolley.
A WARNIN
Failure to mark drill bit, or failure to control
depth of drill bit may result in electrical wir-
ing damage and subsequent electrical
shock.
AWARNING
Set screws must be tightened securely and
roll pin installed to prevent column from
unscrewing during operation. Failure to
install roll pin and tighten set screws
securely could result in light falling from
ceiling.
NOTE: Ensure column is vertical to pre-
vent trolley from drifting. Adjust pallet
with shims if necessary.
lectronic Ph ontrol
25. Connect electronic phase control to wiring in
column with 2-pin Mate-n-Lok® connector.
À CAUTION
To prevent wires from twisting, do not rotate
electronic phase control with column.
26. Gently slide the electronic phase control into
one column with column weld seam A cen-
tered
between the heat sink ears B. The
retaining spring C should engage the inside
of the column.

LFTII (TRACK LIGHT) INSTALLATION,
continued
Arm Assembl tallation — Il
27. Remove stop screw from arm mounting col-
lar.
Raise LFTII arm assembly close to column.
28. Connect electronic phase control to wiring in
arm mounting collar with 4-pin Mate-n-Lok®
connector.
29. Screw arm mounting collar to column.
30. Insert and tighten two column adapter set
screws. Thread on column should not show.
31. Replace stop screw to prevent more than
360° rotation.
If column stop adjustment location is
required, see adjustment section.
NOTE: Column stop adjustment must be
performed before installation of roll pin.
Arm mbly — LFTII
Set screws must be tightened securely and
roll pin installed to prevent column from
unscrewing during operation. Failure to
install roll pin and tighten set screws
securely could result in light falling from ceil-
ing.
32. Place a piece of electrical tape around a 1/8“
drill bit to mark depth to which pilot hole is to
be drilled.
33. Locate 3/32” pilot hole opposite set screw
in column adapter and drill a 1/8“ hole
through the adapter/column assembly using
drill bit.
AWARNING
Failure to mark drill bit, or failure to control
depth of drill bit may result in electrical wir-
ing damage and subsequent electrical shock.
34. Drive in roll pin flush with outside edge of col-
umn adapter.
Make sure trolley rolls freely. For adjustment
of trolley, refer to Adjustment section.
35. Apply power to LFTII. Inspect operation by
turning on light and rotating dimmer control
at base of column from lower to higher light
intensity limits.