Siemens MAMMOMAT Novation DR User manual

MAMMOMAT Novation
DR
English
Print No.: SPB7-250.815.01.02.02 Doc. Gen. Date: 09.04
Replaces: SPB7-250.815.01.01.02
© Siemens AG 2004
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
SP
System
with WH AWS
Startup

MAMMOMAT Novation
DR SPB7-250.815.02 Page 2 of 4 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
0 - 2 Revision
Document revision level
The document corresponds to the version/revision level effective at the time of system
delivery. Revisions to hardcopy documentation are not automatically distributed.
Please contact your local Siemens office to order current revision levels.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise
authorized by Siemens or one of its affiliates to provide such services.
Assemblers and other persons who are not employed by or otherwise directly affiliated
with or authorized by Siemens or one of its affiliates are directed to contact one of the
local offices of Siemens or one of its affiliates before attempting installation or service pro-
cedures.

Contents 0 - 3
Siemens AG SPB7-250.815.02 Page 3 of 6 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
1 _______Prerequisites __________________________________________________ 1 - 1
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
Meters, appliances and tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Auxiliary Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Phantoms / Auxiliary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
2 _______Important Notes________________________________________________ 2 - 1
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
Factory Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
Special checks and protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
Acceptance Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
Protective measures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
System Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
PC Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
Metal Curtain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 2
Measurements with the oscilloscope . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
Swivel-arm rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
Service Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3
Delay times between two exposures . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 4
3 _______Power up the MAMMOMAT Stand _________________________________ 3 - 1
Radiation protection door switch (optional) . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
External exposure lamp (optional). . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Mains voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2
Electrical power to mains input: . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2
Connections:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
Measuring the line resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4
Checking the supply voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4
Checking the microprocessors LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5
Startup of the MAMMOMAT Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5
Startup of the Acquisition Workstation . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6
Arranging the swivel arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 6
4 _______Detector installation ____________________________________________ 4 - 1
Unpacking of the detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Mounting the detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4
Mounting the grid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5
Adjusting the switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6
Mounting the covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6
5 _______Mechanical Checks _____________________________________________ 5 - 1
Mounting covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Page

0 - 4 Contents
MAMMOMAT Novation
DR SPB7-250.815.02 Page 4 of 6 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
Cable duct covers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Swivel arm covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Side covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Front cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 2
Stand covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3
Face shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
Mechanical Checks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5
Rotary motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5
Vertical adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
Emergency stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
Checking the field light time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 8
Adjusting the field light time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9
Checking the compression device . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 9
Decompression button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 11
Checking the OPCOMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 11
Checking the exposure blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 12
6 ______ X-ray tube checks ______________________________________________6 - 1
Tube high voltage, current and mAs values . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Measurement method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Checks with a large focus and without AEC . . . . . . . . . . . . . . . . . . . . 6 - 3
Checks with a small focus and without AEC . . . . . . . . . . . . . . . . . . . . 6 - 4
Checks with a large focus and with AEC . . . . . . . . . . . . . . . . . . . . . . 6 - 5
7 ______ Collimator Adjustment __________________________________________7 - 1
Automatic collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Collimator reference axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Collimator check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2
Collimator beam calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2
Collimator field light calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 4
Collimator Wing Difference Calibration . . . . . . . . . . . . . . . . . . . . . . . 7 - 5
8 ______ Checking dose settings _________________________________________8 - 1
Enable/Disable Dose Calculation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
Configuring of Dose Calculation System . . . . . . . . . . . . . . . . . . . . . . 8 - 1
Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 2
Checking OPDOSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 3
Checking the AEC dose settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 4
Checking the H & D dose settings for Mo/Mo. . . . . . . . . . . . . . . . . . . . 8 - 4
Check the H & D dose settings for Mo/Rh and W/Rh. . . . . . . . . . . . . . . . 8 - 7
Adjust the H and D Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 8
9 ______ Image Quality __________________________________________________9 - 1
Checking Grid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
Page

Contents 0 - 5
Siemens AG SPB7-250.815.02 Page 5 of 6 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Checking visibility of grid lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
Measuring grid lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 3
Eliminating Grid lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 4
Checking Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 8
Calibration of detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 8
Creation of new pixel map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 14
Quality Control Manual Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 20
10 ______Final procedures ______________________________________________ 10 - 1
Settings date and time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
BRICK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 1
Service PC and measuring instruments. . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Saving the configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Reset the exposure counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Deleting the error buffer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Saving the MAMMOMAT Parameters . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Remove the measuring instruments. . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
Checking the protective grounding resistance. . . . . . . . . . . . . . . . . . . . . 10 - 3
Warning label on control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4
Quality Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 4
11 ______Startup Protocol ______________________________________________ 11 - 1
Site Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1
Auxiliary Materials used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1
Installation and Startup steps performed . . . . . . . . . . . . . . . . . . . . . . . 11 - 2
Startup Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 4
Tube high voltage, current and mAs values . . . . . . . . . . . . . . . . . . . . 11 - 4
Collimator beam calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 6
Collimator field light calibration . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 6
AEC Dose Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 6
OPDOSE Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 7
Checking Grid Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 7
Activity report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 8
General remarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 9
12 ______Appendix ____________________________________________________ 12 - 1
Troubleshooting Image Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
Working with the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 4
Description of the syntax used in these instructions. . . . . . . . . . . . . . . . 12 - 4
Connecting the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 5
Configuration of the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 5
Configuration of computer BIOS. . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 5
Configuration of Windows® 2000 Pro . . . . . . . . . . . . . . . . . . . . . . . 12 - 5
Starting up and using the service PC . . . . . . . . . . . . . . . . . . . . . . . 12 - 6
Page

0 - 6 Contents
MAMMOMAT Novation
DR SPB7-250.815.02 Page 6 of 6 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
Troubleshooting PC connection . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 6
13 _____ Changes to previous version ____________________________________13 - 1
Page

1 - 1
Siemens AG SPB7-250.815.02 Page 1 of 4 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Prerequisites 1
Configuration 1
The configuration of the MAMMOMAT Novation
DR installation depends on the customer’s
choice.
Unless otherwise stated, these instructions describe the
•MAMMOMAT Novation
DR Stand with the pivoted object table arm (fixed) and the
integrated generator,
•radiation shield with the integrated control console
•detector and
• syngo Acquisition Workstation.
Depending on the installation configuration, some points may be omitted.
Fig. 1 Configuration
basic unit
MAMMOMAT Novation
DR
tube assembly with filter disc
Mo 0.03/Rh 0.025/Rh 0.050
Molybdenum/tungsten anode X-ray
Integrated Generator
Dose Calculation System
Control console
with integrated radiation
shield (optional)
A
cquisition Workstation

MAMMOMAT Novation
DR SPB7-250.815.02 Page 2 of 4 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
1 - 2 Prerequisites
Meters, appliances and tools 1
Auxiliary Materials 1
Calibrated instruments are required.
Item Remarks Material
Number
With
Sys-
tem
Oscilloscope >50MHz with memory e.g. TEKTRONIK 314 no
Digital multimeter including an mAs
meter
e.g. FLUKE 8060A
or FLUKE 87
97 02 101
97 03 976
no
Service PC See the CS Intranet (
CS/For Service/Common
Services/Service Laptop
for CSEs) for details.
no
Power line impedance meter 84 28 104 no
Power ground-wire tester 44 15 899 no
Luminance meter (for monitor calibra-
tion)
e.g. Mavo Monitor
or Wellhöfer LXplus (05 146
167)
97 02 432 no
Luminance meter (measures the light
intensity from the X-ray field)
e.g. SMfit Mammo 88 81 281 no
Dose meter e.g. Solidose 88 81 323 no
Ion chamber For dose meter Solidose 88 81 315 no
Densitometer e.g. X-Rite 331 97 02 416 no
A non-invasive digital kV meter If not available in the district,
a scope can be used
instead
no
Tab. 1 Meters, appliances and tools
NOTE

Prerequisites 1 - 3
Siemens AG SPB7-250.815.02 Page 3 of 4 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Phantoms / Auxiliary 1
Tools 1
Item Remarks Material
Number
With
Sys-
tem
RMI 156 88 81 265 no
Three, 2 cm plexi (PMMA) 65 61 232 yes
2 mm steel plate, 30x25 cm 66 55 851 yes
2 mm steel plate, 3x10 cm 66 55 844 yes
One 0.1 mm, two 0.2 mm and one 0.5
mm sheets of aluminum 99% (1100)
alloy, 4x4 cm
88 81 273 no
Mammography line pair phantom 2-10 lp/mm 88 81 299 no
Collimator mounted plexi (4 cm) yes
Compression plate simulator yes
4.2 cm plexi Size of the detector 74 47 720 no
Ethernet cable no
Serial PC cable RS232 / Array / BRICK 66 55 745 yes
Serial PC cable RS232 / Stand 99 00 440 no
Cassette / Film 24x30 cm no
Centering cross 96 60 051 no
Tab. 2 Phantoms and auxiliaries
Item Remarks
With
Sys-
tem
Standard installation and service tools no
Torque wrench for bolting the stand/
console to the floor
no
Electrical screwdriver with adjustable
torque is recommended
no
Tab. 3 Tools

MAMMOMAT Novation
DR SPB7-250.815.02 Page 4 of 4 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
1 - 4 Prerequisites
This page intentionally left blank.

2 - 1
Siemens AG SPB7-250.815.02 Page 1 of 4 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Important Notes 2
Symbols 2
"This symbol indicates that the measured values have to be entered in the
"Startup Protocol" on page 11 - 1.
Factory Adjustments 2
The MAMMOMAT NovationDR is adjusted, programmed and tested in the factory, leaving
the adaptation to the on-site mains voltage, adjustment of the AEC and the functional
tests to be performed.
When the measurements to be made (kV, mAs, etc.) are within the tolerances stated in
these instructions, this confirms that the settings made in the factory have not changed
and the equipment is fully serviceable.
The equipment tested with 400 V, 2-phase in the factory.
Special checks and protocols 2
Acceptance Test 2
The acceptance test of the MAMMOMAT Novation
DR is recommended to be performed
whenever a new MAMMOMAT
Novation
DR system has been installed and whenever
changes that might affect performance have been made to an existing system.
The acceptance test of MAMMOMAT
Novation
DR involves performance of all QC proce-
dures in this Quality Control Manual (SPB7-250.623.02...) ensuring that a basic mini-
mum image quality criteria is met before the system is used with patients.
All yearly tests from the Quality Control Manual have to be performed.
Depending on the country where the system is installed, additional tests have to be per-
formed.
•RöV §16 regulations have to performed in Germany.
•The DHHS regulations have to be performed in the USA.
Maintenance measurements must be made according to the DHHS Maintenance
Instructions (SPB7-250.662.01...) and the DHHS Supplements to the instructions
for use (SPB7-250.661.01...). Results must be recorded in DHHS Measurement
certificates (SPB7-250.663.01...).
This symbol indicates exposure of X-ray radiation.

MAMMOMAT Novation
DR SPB7-250.815.02 Page 2 of 4 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
2 - 2 Important Notes
Protective measures 2
System Power Supply 2
It is very important that any intervention in the equipment will start with disconnecting it
from the power supply with the main circuit-breaker. Before removing or inserting any of
the printed circuit boards, switch off the equipment.
PC Boards 2
Metal Curtain 2
If the system is only switched off at the control panel, the line
voltage will still be present at the generator line connection (see
wiring diagram).
A life-threatening hazard of electric shock exists.
After shut-down of the system, there may still be 380 V DC
present on the intermediate circuit.
A life-threatening hazard of electric shock exists.
The PC boards contain electrostatic highly sensitive components.
If disregarded, the components could be damaged.
Use ESD equipment, ground prior to making contact and place
the components on a conductive surface.
The edges of the metal curtain of the stand are very sharp.
They may cause severe injury.
These strips must always be applied onto the edges of the metal
curtain during service and maintenance work.
WARNING
WARNING
CAUTION
WARNING

Important Notes 2 - 3
Siemens AG SPB7-250.815.02 Page 3 of 4 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Apply the protective strips after removing the covers from the stand. Remove the protec-
tive strips only when the covers are to be mounted or when vertical adjustment of the
swivel arm system is necessary.
Holders (2/Fig. 1) for storing the protective strips when not in use are provided on both
sides of the curtain.
Measurements with the oscilloscope 2
Swivel-arm rotation 2
Service Software 2
The MAMMOMAT Novation
DR has various service software packages:
•Acquisition Workstation
The Acquisition Workstation service software is web-based and can be started from the
Options application menu.
•BRICK
The BRICK service software can be accessed via the Acquisition Workstation.
Fig. 1 Protective strips for the metal curtain
The existing ground conductor in the mains cable must under no
circumstances be disconnected when operating the oscilloscope.
A life-threatening hazard of electric shock exists.
For measurements in which a resulting ground loop may falsify
the measuring result, use the differential amplifier (difference
measurement).
Never rotate the swivel arm with the detector wing in the parking
position. This will damage the main cable harness.
2
1
MAM00084
WARNING
WARNING

MAMMOMAT Novation
DR SPB7-250.815.02 Page 4 of 4 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
2 - 4 Important Notes
•MAMMOMAT stand.
The Service PC is required for MAMMOMAT stand service software.
A description of the various service software packages can be found in the MAMMOMAT
Novation
DR Software manual (SPB7-250.816.02...).
Delay times between two exposures 2
The delay times listed below must be followed to prevent the tube from overheating.
When the generator is switched off with the service PC con-
nected,
wait approximately 5 seconds before switching it on again
(The LED’s H3 and H4 have to be off).
Exposure mAs value Delay time between two exposures (seconds)
max. 100 min. 15
max. 200 min. 30
max. 300 min. 45
max. 400 min. 60
max. 500 min. 75
Tab. 1 Delay times between two exposures
NOTE

3 - 1
Siemens AG SPB7-250.815.02 Page 1 of 6 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Power up the MAMMOMAT Stand 3
Radiation protection door switch (optional) 3
It is optional to connect a radiation protection door switch to the MAMMOMAT Novation
DR
master board D750 connector X754.
A 15V / 5 mA signal is used in the door switch circuit. When the signal path is opened by
the door switch, the exposure will immediately be terminated.
1. To connect a door switch, remove the jumper from the X754 (Pin 1,2) located on
the master board D750, see Fig. 1, and connect the door switch instead.
If a radiation protections door switch is not used, a jumper, see Fig. 1, on the master board
750 at connector X754 (Pin 1,2) has to be inserted.
External exposure lamp (optional) 3
This should only be performed if the customer requires it.
The connection on the Master board works as a shutter. The signal from the Master board
is only active during exposure, thus the exposure lamp will only be lit when the signal is
active.
Connect the cable to the lamp holder in series with the power supply.
A radiation protection door switch is not delivered with the MAM-
MOMAT
Novation
DR.
When connecting the exposure lamp to the Master board, make
sure that the electrical load does not exceed 24VAC / 25W
NOTE
Fig. 1 Connecting the door switch
CAUTION

MAMMOMAT Novation
DR SPB7-250.815.02 Page 2 of 6 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
3 - 2 Power up the MAMMOMAT Stand
1. Connect the exposure lamp to the connector X759 located on the Master board
D750, see Fig. 2.
Mains voltage 3
The mains input can be either 1-phase or 2-phase, 50 or 60 Hz.
Electrical power to mains input: 3
Mains voltage 1-phase: 208, 230, 240 and 277 V ±10%
or
2-phase: 208, 230, 240, 277 and 400 V ±10%
Mains Frequency: 50 or 60 Hz
Maximum load: 10kVA (momentary) and 0.8 kVA (long time load).
Fuse: 25 A (external) 208 -> 400 V.
Do not use power from the MAMMOMAT stand.
Before the power for the MAMMOMAT is turned on, make sure,
that the cable plugs (left and right of the system) for the Magnifi-
cation table are not shorted.
Fig. 2 Connecting the exposure lamp
NOTE
WARNING
Magnification
table cable

Power up the MAMMOMAT Stand 3 - 3
Siemens AG SPB7-250.815.02 Page 3 of 6 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Connections: 3
1. Connect the incoming mains cable to the mains terminal (Fig. 3) at the bottom of
the back of the stand.
2. Strain-relieve the incoming mains cable.
Power
system
Type of
connection
Power voltage Power
connections
Single phase Phase to neutral 208 V-277 V Connect to 3 and 4 (see 1/Fig. 3)
Two phase Phase to phase 208 V-400 V
phase to phase.
Note: Max 277 V
phase to neutral/
ground allowed.
Connect to 3 and 4 (see 1/Fig.
3).
Use two phases (of three) in a
normal power distribution sys-
tem.The left over wires, neutral
and the third phase may be con-
nected to terminal 1 and 2. See
Fig. 3.
Fig. 3Incoming mains cable

MAMMOMAT Novation
DR SPB7-250.815.02 Page 4 of 6 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
3 - 4 Power up the MAMMOMAT Stand
Measuring the line resistance 3
1. Connect the line resistance meter to the mains input terminal on the stand.
2. Mains supply ON.
3. Carry out measurement.
4. Mains supply OFF.
To achieve the maximum output, the line resistance must not exceed the following values:
Checking the supply voltages 3
The correct supply voltages +5 V, +15 V and +28 V have already been tested in the fac-
tory. Only a visual check of the function is therefore needed.
1. Switch the system ON.
2. Check that the following LED indicators (top to bottom) on the mains input
converter (generator) are on:
Nominal Input Voltage
[VAC]
Line Resistance Rimax
[c]
208 0,45
230 0,50
240 0,60
277 0,65
400 (2-phase) 0,85
Tab. 1 Measuring the line resistance
LED check
28 VP
5 VF
- 15 V
+ 15 V
28 VS
5 V
Tab. 2 LED check

Power up the MAMMOMAT Stand 3 - 5
Siemens AG SPB7-250.815.02 Page 5 of 6 MAMMOMAT Novation
DR
Medical Solutions Rev. 02 09.04 CS SD 24 System
Checking the microprocessors LED’s 3
The following LED’s on the microprocessor p.c. boards (D750) indicate whether the rele-
vant microprocessors are operating correctly.
1. Mains ON.
2. Check that the CPU IC107 status LED’s D13, D14, D15 are continuously ON and
LED D16 is OFF for approximately. 1 second after the mains is switched on.
3. Switch the MAMMOMAT
Novation
DR system power ON by pressing the ON
button on the control console. After approximately. 5 seconds check that the CPU
IC107 status LED D13 is rapidly flashing and the LED’s D14, D15 and D16 are
OFF.
4. Check that LED D25 on the master board D750 is flashing slowly (once per
second).
Startup of the MAMMOMAT Stand 3
1. Make a note of the exposure parameters.
2. Shutdown the MAMMOMAT system completely.
3. Turn the external power switch ON.
4. Check that the power up of the Generator and the BRICK are performed properly.
5. Start the MAMMOMAT system by pressing the power button ON on the control
console.
6. Check that the MAMMOMAT system is powering up correctly.
7. Check that the BRICK and the Acquisition Workstation communication is working
properly (LED’s V2 and V3 need to be green on the BRICK). The PXCM includes
three status LED’s:
V1—Fiber-optic communications status. A red LED that lights to indicate
lack of communication from the DROC. Likely causes are misconnected fiber
optic lines or the Detector being turned off.
V2—PXCM status. A green LED that flashes to indicate normal operation of
the PXCM. If this LED does not light for a significant amount of time (that is, 2
to 3 minutes), restart the system.
V3—Power status. A green LED that lights to indicate that the PXCM is provid-
ing power to the Detector.
8. Check that the operating mode dr is displayed on the control console.
9. Check if the noted exposure parameters are restored correctly.

MAMMOMAT Novation
DR SPB7-250.815.02 Page 6 of 6 Siemens AG
System Rev. 02 09.04 CS SD 24 Medical Solutions
3 - 6 Power up the MAMMOMAT Stand
Startup of the Acquisition Workstation 3
System specific data has to be entered and set.
The startup and configuration of the Acquisition Workstation is described in the document
Startup, WH AWS (SPB7-250.815.02...).
Arranging the swivel arm 3
1. Remove the protective strips from the metal curtain.
2. Run the lifting carriage upwards.
3. Attach the protective strips back onto the metal curtain.
4. Rotate the swivel arm system to 0 degrees by pressing one of the switches for
clockwise rotation on the supporting arm.
5. System and mains OFF.
Never rotate the swivel arm with the detector wing in the parking
position. This will damage the main cable harness.
WARNING