Siemens MOMMOMAT 1000 Instructions and recipes

MAMMOMAT 1000/3000
Register 3 English
Print No.: SPB7-230.033.07.03.02 Doc. Gen. Date: 11.99
Replaces: SPB7-230.033.07.02.02
© Siemens AB 1999
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights,
including rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
65 27 464
Installation
Installation and Start-Up Instructions

Mammomat 1000/3000 Register 3 SPB7-230.033.07 Page 2 of 2 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
0 - 2 Revision
Chapter Page Revision
17 All 03

Contents 0 - 1
Siemens-Elema AB Register 03 SPB7-230.033.07 Page 1 of 4 MAMMOMAT 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-up
1 _______Prerequisites __________________________________________________1 - 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
MAMMOMAT 1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
MAMMOMAT 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2
Meters and appliances, tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
Meters and appliances required . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 3
Important notes on start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 4
Checking and recording for the area of application of the X-ray decree (§16 Germany)1 - 4
Checking and recording for the DHHS area of application . . . . . . . . . . . . . . . 1 - 5
Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
Note on delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 5
2 _______Protective measures ____________________________________________ 2 -1
Protective measures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -1
3 _______Preparatory work_______________________________________________3 - 1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
Unpacking the stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 2
Removing the transport safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 3
Removing the swivel-arm system transport safeguard . . . . . . . . . . . . . . . 3 - 3
Transport safeguard for the lifting carriage . . . . . . . . . . . . . . . . . . . . . 3 - 3
Transport safeguard for the rotary motion. . . . . . . . . . . . . . . . . . . . . . . . 3 - 4
Protective strips for the metal curtain . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 5
Unpacking the generator and mounting the radiation shield (optional) . . . . . . . . . 3 - 6
4 _______Installing the generator and the stand _____________________________4 - 1
Arranging the components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
Notes on installations with separate generator and separate control console. . . . 4 - 1
Free-standing radiation shield (option) . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2
Removing the generator cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 2
Installing the cable ducts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 3
Installations with separate control console . . . . . . . . . . . . . . . . . . . . . 4 - 3
Laying the cable harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 4
Installations with separate control console . . . . . . . . . . . . . . . . . . . . . 4 - 5
Aligning the stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6
5 _______Cable connections______________________________________________5 - 1
EMC measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
EMC measures at the cable entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Page

0 - 2 Contents
MAMMOMAT 1000/3000 Register 03 SPB7-230.033.07 Page 2 of 4 Siemens-Elema AB
Installation and Start-up Rev. 03 11.99 SPS-UD Solna, Sweden
Fitting the hose clamps and ferrite sleeves
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
Note on separate control console and separate generator. . . . . . . . . . . . . 5 - 2
EMC measures on the bottom plate . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 3
Fitting the cables X1, X8 and X9 onto the bottom plate . . . . . . . . . . . . . . 5 - 3
Connecting the stand cable-harness . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 4
High-voltage connectors, alternative types . . . . . . . . . . . . . . . . . . . . . 5 - 4
Connecting the high-voltage connector . . . . . . . . . . . . . . . . . . . . . . . . 5 - 5
Connecting the cable harness to the generator . . . . . . . . . . . . . . . . . . . . 5 - 6
Unit control cable X1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
Filament cable X8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
Power supply cable X14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
IONTOMAT signal cable X10 and X11 . . . . . . . . . . . . . . . . . . . . . . . 5 - 6
Rotating anode cable X9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
Installations with separate control console and separate generator
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 8
Main voltage connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 10
Connecting the incoming mains to the stand (400 V, 2-phase). . . . . . . . . . . . .5 - 11
400 V 2-phase connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - 11
Connecting the mains supply to the generator (400 V, 2-phase). . . . . . . . . . . .5 - 12
Measures for changing from 2-phase to 1-phase connection . . . . . . . . . . .5 - 13
6 ______ Mains connection and power supply_______________________________6 - 1
Checks before powering up the generator . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Measuring the line resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1
Checking the line voltage in the generator . . . . . . . . . . . . . . . . . . . . . . . 6 - 2
Checking the supply voltages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 3
7 ______ Attaching the swivel-arm covers __________________________________7 - 1
Attaching the swivel-arm covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Arranging the swivel-arm system . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1
Connecting the cables to control-button boards and patient handles . . . . . . . 7 - 1
Attaching the side covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2
Attaching the front cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 2
8 ______ Checking the microprocessors ___________________________________8 - 1
Microprocessors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1
9 ______ Checks without high voltage _____________________________________9 - 1
Checks without high voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1
10 _____ Checks with high voltage _______________________________________10 - 1
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 - 1
Checking X-ray tube high voltage, tube currrent and mAs values . . . . . . . . . . .10 - 2
Page

Contents 0 - 3
Siemens-Elema AB Register 03 SPB7-230.033.07 Page 3 of 4 MAMMOMAT 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-up
Tube current reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 2
Oscilloscope diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 3
11 ______Start-up and functional test of the IONTOMAT______________________ 11 - 1
Checking and programming with the service PC . . . . . . . . . . . . . . . . . . . 11 - 1
Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1
Sensitivity correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 2
Correction curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 2
Other film/screen combinations . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 3
Correction curve diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 4
Checking the film density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 8
Checking the automatic transparency adaption. . . . . . . . . . . . . . . . . . . . 11 - 9
Checking the automatic transparency adaption and OPDOSE (MAMMOMAT 3000 only) 11
- 10
Checking cut-off dose and resolution (§16 Germany). . . . . . . . . . . . . . . . .11 - 11
Output values of constancy testing (§16 Germany). . . . . . . . . . . . . . . . . .11 - 12
12 ______Further programming __________________________________________12 - 1
Setting the real time clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
Prerequisite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
Setting the time in the Mammomat . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
Setting the tube-current reduction. . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1
Reducing the generator power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 2
Main menu: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 2
13 ______Checking the swivel-arm system_________________________________13 - 1
Rotary motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1
Vertical adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 2
Emergency stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 3
14 ______Field light ____________________________________________________14 - 1
Checking and adjusting the field light time . . . . . . . . . . . . . . . . . . . . . . 14 - 1
Checking the field light time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 1
Adjusting the field light time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 2
15 ______Checking the compression device and OPCOMP ___________________15 - 1
Checking the compression device. . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 1
Decompression button (only with separate control console) . . . . . . . . . . . 15 - 2
Checking the OPCOMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 3
Adapting OPCOMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 - 3
16 ______Checking the exposure blocking_________________________________16 - 1
Checking the exposure blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 - 1
Page

0 - 4 Contents
MAMMOMAT 1000/3000 Register 03 SPB7-230.033.07 Page 4 of 4 Siemens-Elema AB
Installation and Start-up Rev. 03 11.99 SPS-UD Solna, Sweden
17 _____ Checking the radiation field limitation_____________________________17 - 1
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 - 1
Measuring procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 - 2
Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 - 3
Alignment radiation field/light field . . . . . . . . . . . . . . . . . . . . . . . . .17 - 3
Radiation field limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 - 3
18 _____ Final procedures ______________________________________________18 - 1
Service PC and measuring instruments . . . . . . . . . . . . . . . . . . . . . . . .18 - 1
Recording the programmed values. . . . . . . . . . . . . . . . . . . . . . . . .18 - 1
Reading the exposure counter and deleting the error memory. . . . . . . . . . .18 - 1
Saving the configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 1
Removing the measuring instruments . . . . . . . . . . . . . . . . . . . . . . . . .18 - 2
Checking the protective grounding resistance . . . . . . . . . . . . . . . . . . . . .18 - 2
Mounting the cable duct covers . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 2
Mounting the stand covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 2
Mammomat stand with separate rear side covers. . . . . . . . . . . . . . . . . .18 - 3
Mammomat stand with single rear cover.. . . . . . . . . . . . . . . . . . . . . .18 - 4
Fitting the Mammomat cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 5
Fitting the cable outlet cover . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 5
Mounting the front cover onto the generator . . . . . . . . . . . . . . . . . . . . . .18 - 6
Final protective grounding resistance test . . . . . . . . . . . . . . . . . . . . . . .18 - 6
Face shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 7
Warning label on control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 8
Affixing the identification labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 9
Returning the LINA card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 9
19 _____ Bolting the stand/generator to the floor ___________________________19 - 1
Stativ and generator with integrated radiation shield and control panel . . . . . . . .19 - 1
Installation with separate generator . . . . . . . . . . . . . . . . . . . . . . . .19 - 2
Free-standing radiation shield (option) . . . . . . . . . . . . . . . . . . . . . . .19 - 3
20 _____ Appendix ____________________________________________________20 - 1
Working with the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 1
Description of the syntax used in these instructions . . . . . . . . . . . . . . . .20 - 1
Connecting the service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 2
Starting up and using the service PC. . . . . . . . . . . . . . . . . . . . . . . .20 - 2
Measuring protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 - 3
Page

1 - 1
Siemens-Elema AB Register 3 SP B7-230.033.07 Page 1 of 6 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Prerequisites 1
General 1
The configuration of the Mammomat installation is dependent on the customer’s choice.
Up to twelve various combinations are possible as shown below:
MAMMOMAT 1000 1
Fig. 1
Molybdenum anode X-ray tube
assembly with filter Mo 0.03
Mammomat 1000 - Basic unit
Fixed object-table arm
("Wing 2" no counterweight)
Molybdenum anode X-ray tube
assembly with filter disc
Mo 0.03/Rh 0.025
Generator with integrated
control panel and radiation shield Separate generator
Separate control console
Free-standing radiation shield

Mammomat 1000/3000 Register 3 SP B7-230.033.07 Page 2 of 6 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
1 - 2 Prerequisites
MAMMOMAT 3000 1
Unless otherwise stated, these instructions describe the stand with pivoted object-table
arm and generator with integrated radiation shield and control panel.
Depending on the installation configuration, some points may be omitted.
Fig. 2
A P40 MoW tube will be delivered irrespective of whether the cus-
tomer has chosen the molybdenum/tungsten anode X-ray tube or
the molybdenum anode X-ray tube. In the last case, the tungsten
anode is deselected by the software.
Fixed object-table arm
("Wing 1" + counterweight)
Mammomat 3000 - Basic unit
Pivoting object-table arm
("Wing 1"+ "Wing 2")
Molybdenum/tungsten anode X-ray
tube assembly with filter disc
Mo 0.03/Rh 0.025/Rh 0.050
Molybdenum anode X-ray tube
assembly with filter disc
Mo 0.03/Rh 0.025
Generator with integrated
control panel and radiation shield
Separate generator
Separate control console
Free-standing radiation shield
NOTICE

Prerequisites 1 - 3
Siemens-Elema AB Register 3 SP B7-230.033.07 Page 3 of 6 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Meters and appliances, tools 1
Meters and appliances required 1
•PowerLine Impedance Meter84 28104 RE999.
•Protective ground-wire tester 44 15 899 RV090.
•Oscilloscope, e.gTEKTRONIX 314.
•Digitalmultimeterincl.mAs meter.
•Densitometer e.g PDA 81.
•Service PC (e.gSiemens-Nixdorf PCD 3NSX/20or similar) with connecting cable (PC-
Generator), partno. 99 00440 RE999.
•Normi 7 testbody (provided by the customer) or SIB phantom Type 42 001 (PTW or
INAK).
•Centering cross, part no. 96 60 051RE 999.
•Plexiglassplates, three plates measuring150 mm x20 mm x 20mm and one plate
measuring 150mm x 150 mm x10 mm, partno. 85 49 438 and 9788 423 respectively.
Tools required 1
•Standardinstallationtoolkit.
•Torquewrenchfor boltingthe stand/generatorto thefloor (optional).
•Electrical screwdriver with adjustable torque is recommended.
Calibrated instruments are required.
NOTICE
For safety reasons, the existing protective ground conductor in
the power cord must under no circumstances be disconnected
when operating the oscilloscope. For those measurements, in
which any resulting ground loop may falsify the measuring result,
use the differential amplifier (difference measurement).
WARNING
Checks and/or adjustments, which must be made with X-ray
NOTICE
radiation switched on, are marked with the warning symbol:

Mammomat 1000/3000 Register 3 SP B7-230.033.07 Page 4 of 6 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
1 - 4 Prerequisites
Important notes on start-up 1
The MAMMOMAT is adjusted, programmed and tested in the factory, leaving only the
adaption to the on-site mains voltage and the functional tests to be performed.
When the measurements to be made (kV, mAs, etc.) are within the tolerances stated in
these instructions, this confirms that the settings made in the factory have not changed
and the equipment is fully serviceable.
The measured values marked with ?in Chapter 10 "Checks with high voltage" shall be
entered in the "start-up" column in the test certificate provided.
The service PC is required only for programming according to:
•Chapter 10 "Checks with high voltage"
•Chapter 11 "Start-up and functional test of the IONTOMAT"
Programming the "Correction curve"
Setting the "sensitivity" (film density)
Setting the "sensitivity correction" (adaption to different exposure techniques)
•Chapter 12 "Further programming"
•Chapter 18 "Final procedures"
Description of the Service-PC syntax is found in Chapter 20 "Appendix".
Checking and recording for the area of application of the X-ray
decree (§16 Germany) 1
In the area of application of the X-ray decree, an acceptance test certificate is supplied,
with most of the data filled in by the factory.
Only:
•thecut-offdose
•theresolutionof thefilm/screensystems used
•theoutputvalues ofthe constancy test
must be determined by the owner of the equipment and recorded in the acceptance test
certificate. Furthermore, the front page of the acceptance test certificate must also be
completed with the operator´s data.
If the generator is switched off with the Service PC connected,
wait approximately 5 s before switching it on again.
NOTICE

Prerequisites 1 - 5
Siemens-Elema AB Register 3 SP B7-230.033.07 Page 5 of 6 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Checking and recording for the DHHS area of application 1
In the area of application of the DHHS regulations, maintenance measurements must be
made according to the "DHHS Maintenance Instructions" SPB7-230.662.03.01.02 and the
"DHHS Supplements to the instructions for use" SPB7-230.661.02.01.02.
Sections 1
•Requiredlabels.
•RadiationON indicators.
•Manualterminationofexposure.
•Checkingthe maximumadjustablemAs.
•Filtersin beamlimitingdevice (BLD).
•Reproducibility.
•kVp-accuracy.
•mAs-accuracy.
•Automaticexposurecontrol (AEC).
•Coincidenceof radiationfield/imagereceptor.
•Alignment of light field/X-ray field.
•Illuminanceof lightlocalizer (lightfield).
•Shut-down of motor-driven compression movement.
The result must be recorded in "DHHS Measurement certificates"
SPB7-230.663.03.01.02.
Some of the values to be determined can be taken from the acceptance test certificate.
The radiation-field limitation is set at the factory and recorded in the acceptance test certif-
icate.
If the measurements to be made concerning the radiation-field limitation are within the tol-
erances stated in these instructions, this confirms that the settings made at the factory
have not changed.
Note on delivery state 1
The MAMMOMAT has been tested and adjusted at the factory, and should therefore be
ready for operation after completion of the installation.
The equipment is set to 400 V, 2-pase, on delivery.

Mammomat 1000/3000 Register 3 SP B7-230.033.07 Page 6 of 6 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
1 - 6 Prerequisites
This page intentionally left blank.

2 - 1
Siemens-Elema AB Register 3 SP B7-230.033.07 Page 1 of 2 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Protective measures 2
Protective measures 2
It is very important that any intervention in the equipment will start with disconnecting it
from the power supply with the main circuit-breaker. Before removing or inserting any of
the printed circuit board, switch of the equipment. To prevent accidental triggering of high
voltage and radiation, set the switch S2 (SS) on p.c. board D702 to "OFF" (lower position,
no triggering of the SS relay).
If the system is only switched off at the control panel or with
S2/D711, line voltage will still be present at the generator line
connection, line filter Z1, Z2, transformer T1, transformer T10 and
p.c. board D711 (see wiring diagram).
WARNING
After shut-down of the system, there may still be 380 V DC
present on the intermediate circuit. This will be indicated by LED
V24 on p.c. board D710. The voltage will drop to less than 30 V
within about 3 minutes, the LED goes out at about 30 V.
WARNING
The p.c. boards contain electrostatic highly sensitive components
requiring particular care in their handling (ground before making
contact and place only on a conductive surface).
CAUTION
The edges of the metal curtain of the stand are very sharp and
may cause severe injury. Apply the protective strips as mentioned
in section Protective Measures after removing the covers from th
e
the stand. Remove the protective strips only when the covers are
to be mounted or when vertical adjustment of the swivel-arm
WARNING
system is necessary.

Mammomat 1000/3000 Register 3 SP B7-230.033.07 Page 2 of 2 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
2 - 2 Protective measures
This page intentionally left blank.

3 - 1
Siemens-Elema AB Register 03 SP B7-230.033.07 Page 1 of 8 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Preparatory work 3
General 3
Scope of delivery 3
The MAMMOMAT is normally packed in one crate and one cardboard box (the number of
packages is dependent on the customer’s choice, however):
Crate (length 2140 mm, width 800 mm, height 1375 mm)
The crate contains:
•Compressionplate
•Standwith X-raytube assemblyand baseplate
•Objecttable 18 cmx 24 cm(Bucky)
•Externaldiaphragm
•Coverpanels
•Installationmaterial
•Optional:Stanchionsforthelead-glasspane (radiationshield)
•Cableducts
•Technicaldocuments
Cardboard box (lenght 1210 mm, width 820 mm, height 700 mm)
The cardboard box contains:
•Generatorwith integratedcontrolpanel,high-voltagegeneratorandbaseplate.
•Optional:Lead-glasspane
•Optional:Separatecontrolconsole
Further accessories are packed in a separate cardboard box.
Unpacking 3
As a general rule, the directional marks on the crates should be observed during trans-
port, storage and unpacking.
The stand crate is bolted together, while the cardboard box is secured with plastic straps.
Wear safety footwear!
WARNING

Mammomat 1000/3000 Register 03 SP B7-230.033.07 Page 2 of 8 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
3 - 2 Preparatory work
Unpacking the stand 3
Unpacking
1. Openthestand cratebyremoving thetop (1)and thenthe sidewall(2).
2. Take out allenclosed packages (accessories, installation material, cover panels
etc.)from the crate.
3. Removethewoodensupports.
4. Removetheremainingwalls(3).
5. Move the stand and palletto the site of erection.
6. Upend the stand (4), with pallet (5) (two personsare required).
7. Loosen the four bolts (6)and remove the pallet (5).
Fig. 1 Unpacking the stand
MAM00167
1
2
2
1
3
6
5
4

Preparatory work 3 - 3
Siemens-Elema AB Register 03 SP B7-230.033.07 Page 3 of 8 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Removing the transport safeguards 3
Removing the swivel-arm system transport safeguard 3
1. Loosenthe transportsafeguard nuts(1/Fig.2) andremove thetube head screws
(2/Fig.2).
2. Pushthe redtransportsafeguard(3/Fig.2) inwards,away fromthe tubehead.
Transport safeguard for the lifting carriage 3
1. Loosen the two screws (1/Fig. 3) and remove the red transport safeguard (2/Fig.
3). Reinsert screws (1/Fig. 3), they might be needed for service purposes.
Fig. 2 Swivel-arm system transport safeguard
Removal of the swivel-arm system transport safeguard is done
after the equipment has been powered up, see further section
"Attaching the swivel-arm covers" on page 7 - 1.
Fig. 3 Transport safeguard for the lifting carriage
MAM00081
1
2
3
NOTICE
2
1
MAM00082

Mammomat 1000/3000 Register 03 SP B7-230.033.07 Page 4 of 8 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
3 - 4 Preparatory work
2. Cut and remove the cable tie securing the balancing spring during transport.
Transport safeguard for the rotary motion 3
1. Removethetransportsafeguard screw(1/Fig.4) withspacertoenable rotary
motion.
The screw and the spacer should be kept for the mounting ofthe lifting carriage
transportsafeguard.
2. Mount thered lifting carriage transportsafeguard with screw andspacer
(1/Fig.4)on thelefthandsideofthe stand,see Fig.5.Insertthe screwthroughthe
slotfrom theinsideof thestand, see Fig.6
3. Tighten the screw. Make sure that the transport safeguard is parallell to the
stand.
The lifting carriage transport safeguard shall be kept for service
purposes (Fig. 5).
Fig. 4 Transport safeguard for the rotary motion
Fig. 5 Transport safeguard mounted on the stand Fig. 6 Screw and spacer inserted from the inside of the
stand
NOTICE
1
MAM00083
MAM00312
MAM00313
MAM00314

Preparatory work 3 - 5
Siemens-Elema AB Register 03 SP B7-230.033.07 Page 5 of 8 Mammomat 1000/3000
Solna, Sweden Rev. 03 11.99 SPS-UD Installation and Start-Up
Protective strips for the metal curtain 3
The edges of the metal curtain are very sharp and are therefore provided with protective
strips (1) on delivery. These strips must always be applied onto the edges of the metal
curtain during service and maintenance work.
Holders (2) for storing the protective strips when not in use, are provided on both sides of
the curtain, see Fig. 7.
Fig. 7 Protective strips for the metal curtain
The protective strips must be removed from the metal curtain
before any vertical adjustment of the swivel-arm system is
performed.
2
1
MAM00084
CAUTION

Mammomat 1000/3000 Register 03 SP B7-230.033.07 Page 6 of 8 Siemens-Elema AB
Installation and Start-Up Rev. 03 11.99 SPS-UD Solna, Sweden
3 - 6 Preparatory work
Unpacking the generator and mounting the radiation shield
(optional) 3
1. Openthecardboardboxbycuttingtheplasticstraps.
2. Lift out the lead-glassand put it awayin a safe place.
3. Remove the protective coverfrom the generator.
4. Upend the generator(1/Fig. 8) and lift it off the pallet (2/Fig. 8) (two persons are
required).
Fig. 8 Unpacking the generator
MAM00085
3
4
3
2
1