Siemens SIREMOBIL User manual

SIREMOBIL
English
Print No.: SPR2-130.812.06.01.02 Doc. Gen. Date: 12.02
Replaces: n.a.
© Siemens AG 2002
The reproduction, transmission or
use of this document or its contents
is not permitted without express
written authority. Offenders will be
liable for damages. All rights, in-
cluding rights created by patent
grant or registration of a utility
model _or_design,_are_reserved.
SP
System Manual
Installation Instructions
Installation of the Key Switch

SIREMOBIL SPR2-130.812.06 Page 2 of 6 Siemens AG
System Manual Rev. 01 12.02 CS PS 24 Medical Solutions
2 Installation and Startup1
Safety information 1
Validity of this document 1
This document is applicable if a key switch is to be retrofitted to the SIREMOBIL Compact,
SIREMOBIL Compact L, SIREMOBIL Iso-C, POWERMOBIL, and ARCOSKOP systems.
Documents required 1
•System manual of the product
Parts required 1
Tools required 1
•Tool case
•1 set of Allen keys
•1 drilling machine
•1 vacuum cleaner
Measuring equipment required 1
Avoidance of light to severe injuries which may even lead to
death and avoidance of material damage.
The product-specific safety information given in the system man-
ual as well as the safety information contained in the ARTD,
part 2, must be observed.
After all work has been completed and all covers have been
attached, perform the protective conductor test according to
ARTD-002.731.17. The protective conductor resistance must not
exceed 0.2 Ohm.
•Retrofit kit key switch 07140895
•Protective conductor resistance meter
e. g. "Safety Tester Bender UNIMET 1000 ST", Mat. No. 51 38 727
WARNING

Installation and Startup 3
Siemens AG SPR2-130.812.06 Page 3 of 6 SIREMOBIL
Medical Solutions Rev. 01 12.02 CS PS 24 System Manual
Mechanical installation 1
•Open the paneling of the logbook compartment.
•Open the rear paneling of the monitor trolley.
•A protective plate pointing towards the keyboard is installed inside the logbook compart-
ment. Unscrew this plate. Thus, the On/Off button is accessible.
•Mark the drill hole according to Fig. 1.
•Drill a 3.5 mm hole at the marked position (Fig. 1).
•Increase the hole diameter to 22 mm with the step drill (Fig. 1).
•Remove the remaining drilling chips in the monitor trolley with a vacuum cleaner.
Fig. 1 Fig. 2
Avoidance of light to serious injuries which may even lead to
death and avoidance of material damage.
Prior to performing the retrofit work, disconnect the system from
the power supply, and pull out the power plug.
Drill slowly. Make sure that during this process the step drill is
held at a right angle.
Collect the drilling chips inside the monitor trolley with an appro-
priate pad (such as cloth or plastic foil) to avoid short circuits due
to metal chips.
WARNING
Note

SIREMOBIL SPR2-130.812.06 Page 4 of 6 Siemens AG
System Manual Rev. 01 12.02 CS PS 24 Medical Solutions
4 Installation and Startup
•Insert the key switch into the hole from the outside. Make sure that the "0" mark at the
switch is in the vertical position.
•Slide the clamp fitting from the inside on the key switch.
The arrows of the lettering a1-4 mmapoint towards the protective plate.
•Tighten the screw (1/Fig. 3) clockwise, until the key switch is fixed firmly in the hole.
•Do not yet install the switch top (4/Fig. 4).
Fig. 3 Fig. 4
The key switch is delivered ready to assemble (Fig. 4).
For different plate thicknesses, the clamp fitting (1/Fig. 4) can be
pushed onto the key switch at two positions.
Make sure that the clamp fitting is installed with the arrows of the
lettering a1-4 mmapointing towards the key switch (2/Fig. 4).
Tighten the screw of the clamp fitting (2/Fig. 3) clockwise and
loosen it counterclockwise.
After having pressed the latch (1/Fig. 3) in the direction of the
arrow the switch top (4/Fig. 4) of the key switch can be removed.
The switch top can be placed on the key switch in three different
positions and then locked. In the center position the switch is not
actuated by the cams. Therefore, the switch top must be placed
off-center on the key switch and locked into place (3/Fig. 4).
Note

Installation and Startup 5
Siemens AG SPR2-130.812.06 Page 5 of 6 SIREMOBIL
Medical Solutions Rev. 01 12.02 CS PS 24 System Manual
Wiring 1
•Unplug the three-pin connector from the power button.
•Unplug connector D50.X5 on board D50.
•With the SIREMOBIL Iso-C, POWERMOBIL, and ARCOSKOP systems, the cable is ad-
ditionally equipped with the connector X5B. Remove it from the coupling as well.
•Run the new cable corresponding to the existing cable in the monitor trolley.
•Reconnect the 3-pin connector to the power button at the control console of the monitor
trolley.
•Run the two additionally existing cable ends to the key switch, and connect them to the
switch top of the key switch.
•Place the switch top off-center on the key switch and press it down, until it locks into
place.
•Plug in connector D50.X5 on board D50 again.
•With the SIREMOBIL Iso-C, POWERMOBIL, and ARCOSKOP systems, additionally re-
insert the connector X5B in the coupling.
Functional test 1
•Connect the system to the power supply.
•Check the function of the key switch:
- Turn the key switch into position 0. Press the On button at the monitor trolley and at the
basic unit, if existing.
Both times the system must remain switched off.
- Switch on the key switch and press the On button at the monitor trolley.
The system is started.
- After the end of startup, switch the system off. If the basic unit is equipped with an On
button, switch the system on again at the control console of the basic unit after it has
shut down.
The system is started.
- Turn the key switch into position 0.
The system switches off.
•After system shut-down, disconnect it from the power supply, and pull out the power
plug.
The cable between the power buttons (On/Off button at the control con-
sole of the monitor trolley) and the switch-on circuit D50 is replaced by
the cable included in the scope of supply.
Note

SIREMOBIL SPR2-130.812.06 Page 6 of 6 Siemens AG
System Manual Rev. 01 12.02 CS PS 24 Medical Solutions
6 Installation and Startup
Installing the paneling 1
•Reattach the protective plate behind the keyboard in the logbook compartment.
Take care that the cables are not squeezed.
•Refit the paneling of the logbook compartment. Make sure the ground wire connections
are correct when doing this.
•Reinstall the rear paneling of the monitor trolley. Make sure the ground wire connections
are correct when doing this.
Final work 1
•After all work has been completed and all covers have been attached perform the protec-
tive conductor test according to ARTD-002.731.17... The protective conductor resis-
tance must not exceed 0.2 Ohm.
•Add these instructions to the system manual of the product.
•File the Addendum/Supplement to the Operating Instructions included in the scope of
supply into the existing operating instructions.
Customer information 1
•Demonstrate the function of the key switch.
•Hand over the keys.
•Hand over the operating instructions.