Siemens SIMATIC RF650R Instruction sheet

SIMATIC RF650R/RF680R/RF685R
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC Ident
RFID systems
SIMATIC
RF650R/RF680R/RF685R
Configuration Manual
10/2015
C79000
-G8976-C386-03
Introduction
1
Notes on security
2
Description
3
Commissioning
4
Configuration via STEP 7
(PROFINET device)
5
Configuring with the WBM
6
Interface to the SIMATIC
controller
7
XML interface
8
Service and maintenance
9
Appendix
A

Siemens AG
Division Process Industries and Drives
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C386-03
Ⓟ
10/2015 Subject to change
Copyright © Siemens AG 2014 - 2015.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 3
Table of contents
1 Introduction............................................................................................................................................. 7
1.1 Preface......................................................................................................................................7
1.2 Abbreviations and naming conventions ....................................................................................8
2 Notes on security .................................................................................................................................... 9
3 Description............................................................................................................................................ 11
3.1 Properties of the UHF readers................................................................................................11
3.2 User-specific procedures ........................................................................................................14
4 Commissioning ..................................................................................................................................... 17
4.1 Important notes on using the device.......................................................................................17
4.2 Connect the hardware.............................................................................................................19
4.3 Setup/network topology ..........................................................................................................21
4.4 Assign the IP address / device name .....................................................................................22
4.4.1 Assigning the IP address / device name with the PST ...........................................................23
4.4.2 Assigning the IP address / device name with STEP 7............................................................25
5 Configuration via STEP 7 (PROFINET device) ...................................................................................... 29
5.1 Linking readers into STEP 7 (Basic / Professional)................................................................29
5.2 The TIA Portal (STEP 7 Basic / Professional) ........................................................................30
5.3 Overview of the configurable properties .................................................................................31
6 Configuring with the WBM..................................................................................................................... 33
6.1 Starting WBM..........................................................................................................................33
6.2 The WBM ................................................................................................................................35
6.3 The menu items of the WBM ..................................................................................................40
6.3.1 The "Start page" menu item....................................................................................................40
6.3.2 The "Settings - General" menu item .......................................................................................42
6.3.3 The "Settings - Read points" menu item.................................................................................46
6.3.4 The "Settings - Tag fields" menu item ....................................................................................58
6.3.5 The "Settings - Filters" menu item ..........................................................................................60
6.3.6 The "Settings - Digital outputs" menu item .............................................................................64
6.3.7 The "Settings - Communication" menu item ...........................................................................66
6.3.8 The "Settings - Adjust antenna" menu item............................................................................71
6.3.9 The "Settings - Activation power" menu item..........................................................................73
6.3.10 The "Diagnostics - Tag monitor" menu item ...........................................................................77
6.3.11 The "Diagnostics - Log" menu item ........................................................................................80
6.3.12 The "Diagnostics - Messages" menu item ..............................................................................82
6.3.13 The "Edit transponder" menu item..........................................................................................83
6.3.14 The "User management" menu item.......................................................................................87
6.3.15 The "System" menu item ........................................................................................................91

Table of contents
SIMATIC RF650R/RF680R/RF685R
4Configuration Manual, 10/2015, C79000-G8976-C386-03
6.3.16 The "Help" menu item ............................................................................................................ 92
7 Interface to the SIMATIC controller ....................................................................................................... 93
7.1 Retrieving the Ident library ..................................................................................................... 93
7.2 Overview of the Ident library .................................................................................................. 94
7.3 Project preparations............................................................................................................... 95
7.4 Setting the "IID_HW_CONNECT" data type .......................................................................... 97
7.5 General structure of the function blocks ................................................................................ 99
7.6 Programming Ident blocks ................................................................................................... 103
7.6.1 Basic blocks ......................................................................................................................... 103
7.6.1.1 Read..................................................................................................................................... 103
7.6.1.2 Reset_Reader ...................................................................................................................... 104
7.6.1.3 Write..................................................................................................................................... 104
7.6.2 Extended blocks................................................................................................................... 106
7.6.2.1 Config_Upload/-_Download ................................................................................................. 106
7.6.2.2 Inventory .............................................................................................................................. 109
7.6.2.3 Read_EPC_Mem.................................................................................................................. 113
7.6.2.4 Read_TID ............................................................................................................................. 114
7.6.2.5 Set_Param ........................................................................................................................... 115
7.6.2.6 Write_EPC_ID ...................................................................................................................... 117
7.6.2.7 Write_EPC_Mem.................................................................................................................. 118
7.6.2.8 AdvancedCMD ..................................................................................................................... 119
7.6.3 Status blocks........................................................................................................................ 120
7.6.3.1 Reader_Status ..................................................................................................................... 120
7.7 Programming the Ident profile.............................................................................................. 121
7.7.1 Structure of the Ident profile................................................................................................. 121
7.7.2 Overview of the commands ................................................................................................. 123
7.7.3 Command structure ............................................................................................................. 124
7.7.4 Commands........................................................................................................................... 126
7.7.5 Chaining ............................................................................................................................... 130
7.7.6 Command repetition............................................................................................................. 132
7.8 Digital inputs/outputs............................................................................................................ 138
8 XML interface ......................................................................................................................................139
8.1 Functionality of the XML interface........................................................................................ 139
8.2 Demo application ................................................................................................................. 141
8.2.1 Structure of the demo application ........................................................................................ 141
8.2.2 User interface of the demo application ................................................................................ 143
8.2.3 Working with the demo application ...................................................................................... 144
8.3 XML commands ................................................................................................................... 145
8.3.1 Connections ......................................................................................................................... 146
8.3.1.1 hostGreetings....................................................................................................................... 147
8.3.1.2 hostGoodbye........................................................................................................................ 148
8.3.1.3 heartBeat.............................................................................................................................. 149
8.3.2 Reader settings .................................................................................................................... 150
8.3.2.1 setConfiguration................................................................................................................... 150
8.3.2.2 getConfiguration................................................................................................................... 151
8.3.2.3 getConfigVersion.................................................................................................................. 152

Table of contents
SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 5
8.3.2.4 getActiveConfiguration..........................................................................................................153
8.3.2.5 getLogfile ..............................................................................................................................154
8.3.2.6 resetLogfile ...........................................................................................................................155
8.3.2.7 setParameter ........................................................................................................................156
8.3.2.8 getParameter ........................................................................................................................158
8.3.2.9 setTime .................................................................................................................................160
8.3.2.10 getTime .................................................................................................................................161
8.3.2.11 setIO......................................................................................................................................162
8.3.2.12 getIO .....................................................................................................................................164
8.3.2.13 resetReader ..........................................................................................................................165
8.3.2.14 getReaderStatus ...................................................................................................................167
8.3.3 Transponder processing .......................................................................................................168
8.3.3.1 editBlackList..........................................................................................................................169
8.3.3.2 getBlackList...........................................................................................................................170
8.3.3.3 getAllSources........................................................................................................................172
8.3.3.4 triggerSource ........................................................................................................................173
8.3.3.5 readTagIDs ...........................................................................................................................174
8.3.3.6 getObservedTagIDs..............................................................................................................177
8.3.3.7 writeTagID.............................................................................................................................181
8.3.3.8 readTagMemory....................................................................................................................185
8.3.3.9 writeTagMemory ...................................................................................................................189
8.3.3.10 readTagField.........................................................................................................................194
8.3.3.11 writeTagField ........................................................................................................................
198
8.3.3.12 killTag....................................................................................................................................202
8.3.3.13 lockTagBank .........................................................................................................................206
8.3.4 Negative XML replies............................................................................................................211
8.4 XML EventReports................................................................................................................214
8.4.1 Events ...................................................................................................................................214
8.4.1.1 tagEventReport .....................................................................................................................214
8.4.1.2 rssiEventReport ....................................................................................................................218
8.4.1.3 ioEventReport .......................................................................................................................220
8.4.2 Interrupts...............................................................................................................................222
9 Service and maintenance.................................................................................................................... 225
9.1 Diagnostics ...........................................................................................................................225
9.1.1 Diagnostics via the LED displays..........................................................................................226
9.1.2 Diagnostics via display elements..........................................................................................228
9.1.3 Diagnostics via SNMP ..........................................................................................................229
9.1.4 Diagnostics using the WBM..................................................................................................229
9.1.5 Diagnostics using the TIA Portal (STEP 7 Basic / Professional)..........................................230
9.2 Error messages.....................................................................................................................232
9.2.1 How the LED status display works .......................................................................................233
9.2.2 RF650R/RF680R/RF685R error messages..........................................................................234
9.3 Module replacement .............................................................................................................240
9.3.1 Backup configuration data ....................................................................................................240
9.3.2 Replacing a module ..............................................................................................................243
9.4 Firmware update ...................................................................................................................244
9.5 Restore to factory settings ....................................................................................................245

Table of contents
SIMATIC RF650R/RF680R/RF685R
6Configuration Manual, 10/2015, C79000-G8976-C386-03
A Appendix .............................................................................................................................................247
A.1 Planning and installation of UHF read points....................................................................... 247
A.1.1 Technical basics................................................................................................................... 247
A.1.2 Implementation of UHF RFID installations........................................................................... 250
A.1.2.1 Preparation phase................................................................................................................ 250
A.1.2.2 Test phase ........................................................................................................................... 252
A.1.2.3 Setting up read points .......................................................................................................... 252
A.1.3 Dealing with field disturbances ............................................................................................ 256
A.1.3.1 Types and approaches to solutions ..................................................................................... 256
A.1.3.2 Measures for eliminating field disturbances......................................................................... 258
A.2 Command and acknowledgement frames ........................................................................... 260
A.2.1 Structure of the command frame ......................................................................................... 260
A.2.2 READER-STATUS............................................................................................................... 261
A.2.3 INVENTORY ........................................................................................................................ 262
A.2.4 PHYSICAL-READ ................................................................................................................ 263
A.2.5 PHYSICAL-WRITE............................................................................................................... 264
A.2.6 WRITE-ID............................................................................................................................. 265
A.2.7 KILL-TAG ............................................................................................................................. 266
A.2.8 LOCK-TAG-BANK................................................................................................................ 267
A.2.9 EDIT-BLACKLIST ................................................................................................................ 268
A.2.10 GET-BLACKLIST ................................................................................................................. 269
A.2.11 READ-CONFIG .................................................................................................................... 270
A.2.12 WRITE-CONFIG .................................................................................................................. 271
A.3 Service & Support ................................................................................................................ 272

SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 7
Introduction
1
1.1
Preface
Purpose of this document
This manual contains all the information required for the parameter assignment and
commissioning of the RF650R, RF680R and RF685R readers of the SIMATIC RF600
system.
This manual is intended for:
●Commissioning engineers
●Configuration engineers
●Service technicians
Scope of validity of this document
This documentation is valid for all supplied versions of the SIMATIC
RF650R/RF680R/RF685R readers and describes the delivery state as of 10/2015 and
firmware version V2.1.
Registered trademarks
SIMATIC ®, SIMATIC RF ®, MOBY ®, RF MANAGER ® and SIMATIC Sensors ® are registered
trademarks of Siemens AG.
Documentation classification
You will find further information on the properties, technical specifications and possible
applications of the RF650R, RF680R and RF685R readers in the "SIMATIC RF600 System
Manual (https://support.industry.siemens.com/cs/ww/en/view/22437600)".
You will find more information on operating the readers via communications modules
(PROFIBUS operation) in the manuals of the relevant communications module
(https://support.industry.siemens.com/cs/ww/en/ps/15105/man).
For S7 programmers who create their own command and acknowledgment frames, the
communications rules and frames that are required can be found in the Appendix in the
section "Command and acknowledgement frames (Page 260)". XML programmers will find
the required communications rules and frames in the section "XML interface (Page 139)".

Introduction
1.2 Abbreviations and naming conventions
SIMATIC RF650R/RF680R/RF685R
8Configuration Manual, 10/2015, C79000-G8976-C386-03
Specifications
The Ident blocks in the manual are based on the "Proxy Ident Function Block" protocol. You
can obtain the specification of the "Proxy Ident Function Block" from the PROFIBUS User
Organization. You will also find further information on the Ident blocks and the Ident profile in
the manual "Ident profile and Ident blocks, standard function for Ident systems
(https://support.industry.siemens.com/cs/ww/en/view/106368029)".
At several points, the manual references the "EPCglobal Specification". This standard
essentially describes the communication between transponders and RFID readers. You will
find the specification on the Internet at "GS1 (http://www.gs1.org)"
History
The following edition(s) of the configuration manual have been published up to now:
Edition
Note
10/2014
First edition
07/2015 Revised and expanded edition.
Expansion of the documentation by the following:
•PROFIBUS connection
•MRP and SNMP capability
•Capability of processing transponders of the ISO 18000-6B standard
10/2015
Revised and expanded edition
1.2
Abbreviations and naming conventions
The following terms/abbreviations are used synonymously in this document:
Write/read device (SLG)
Readers
Mobile data storage unit (MDS)
Transponder, tag
Interface module (ASM)
Communications module (CM)

SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 9
Notes on security
2
Recommendations for secure handling of the WBM
Keep to the following security recommendations when working with the WBM (Web Based
Management) to prevent unauthorized access to the device:
●Enable user management and create new profiles.
●Before making the device available, change the default passwords for the standard
profiles "Administrator" and "User".
●Use strong passwords.
●You should not use the same passwords for different user names or systems.
●Enable only the services (communications protocols) that will actually be used on the
device and also the installed interfaces/ports. Unused ports could be used to access the
network downstream from the device.
●If a firewall is necessary, configure and start the firewall before you connect the device to
a public network. Make sure that the firewall is configured so that it accepts connections
from a specific domain.
●Check the device regularly to make sure that these recommendations and/or other
internal security guidelines are adhered to.
●The configuration files are available in XML format for simple use. Make sure that the
configuration files outside the device are suitably protected. You can, for example,
encrypt the files, store them at a safe location and transfer them only via secure
communications channels.
●Do not connect the device directly to the Internet. Operate the device within a protected
network area.
●The firmware itself is signed and encrypted. This ensures that only authentic firmware can
be downloaded to the device.
●Check for non-secure protocols activated on the device. While some protocols such as
HTTPS are secure, others such as HTTP were not developed for this purpose. With non-
secure protocols, suitable security measures must be taken to prevent unauthorized
access to the device/network.
●Check regularly that the device complies with these recommendations and /or other
internal security policies.
●Evaluate your plant as a whole in terms of security. Use the cell protection concept with
suitable products.

Notes on security
SIMATIC RF650R/RF680R/RF685R
10 Configuration Manual, 10/2015, C79000-G8976-C386-03

SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 11
Description
3
3.1
Properties of the UHF readers
Area of application
The UHF readers SIMATIC RF650R, RF680R and RF685R are intended for use in logistics
and in automation. The RF680R and RF685R readers are intended for use in automation
environments, for example on a production line but are equally suitable for applications in
logistics. To meet these requirements, the readers were equipped with a high transmit power
and degree of protection (IP65). For applications in logistics with less demanding
requirements relating to the protection class and transmit power, the RF650R reader is a
cost-effective alternative. All readers are equipped with extensive diagnostics options and
can process ISO 18000-6C and ISO 18000-6B transponders.
The RF685R has one special feature with its internal, adaptive antenna. This significantly
increases the reliability of read and write actions even under difficult radio conditions.
The RF680R and RF685R readers are either integrated without problems in SIMATIC S7
automation systems via an integrated PROFINET connector or via the RS-422 interface and
the ASM 456 communications module via PROFIBUS. Suitable programming blocks are
available. The connection to PC environments is via Ethernet using TCP/IP and the XML
protocol. A second Ethernet interface (both M12) can be used for diagnostics during
operation so that the connection to the higher-level system does not need to be interrupted.
The RF650R has one Ethernet interface (RJ-45). This is used both to connect to PC systems
as well as for configuration and diagnostics and it can also be used during operation. Higher-
level software communicates with the reader using TCP/IP and the XML protocol.
The WBM (Web Based Management) allows commissioning, configuration and diagnostics
of all three devices using an Internet browser. This makes additional updates and installation
of configuration and diagnostics software unnecessary.

Description
3.1 Properties of the UHF readers
SIMATIC RF650R/RF680R/RF685R
12 Configuration Manual, 10/2015, C79000-G8976-C386-03
Characteristics
The following characteristics distinguish the SIMATIC RF650R, RF680R and RF685R UHF
readers:
Table 3- 1 Characteristics of the readers
Characteristics
RF650R
RF680R
RF685R
Antennas 4 x external antenna connectors 1 x internal, adaptive
antenna
1 x external antenna
connector
Transmit power
1000 mW
2000 mW
Digital inputs/outputs
4 x digital inputs and 4 x digital outputs
RS-422 interface
--
1 x plug M12 8-pin
PROFIBUS connection
via CM
-- ASM 456
(115.2 kbps)
Ethernet interface 1 x Industrial Ethernet,
RJ-45
(TCP/IP with XML pro-
tocol)
2 x Industrial Ethernet, M12
(TCP/IP with XML protocol or PROFINET)
Max. transmission
speed
100 Mbps 100 Mbps
Degree of protection
IP30
IP65
Configura-
tion/diagnostics options
WBM (browser) WBM (browser)
STEP 7 (S7)
Interfaces to
PC/controller
XML interface XML interface
SIMATIC interface
Note
Minimum supported block size of a controller
When operating with a controller, make sure that blocks wi
th a minimum size of > 16 KB are
supported.
Note
IRT is not supported
Note that the RF680R/RF685R readers do not support IRT (Isochronous Real Time). The
readers can also not function as IRT conductors.
The readers can be configured as clients in MRP r
ings. Network diagnostics via SNMP is
supported by the readers.

Description
3.1 Properties of the UHF readers
SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 13
Certificates
The readers RF680R and RF685R support the following certificates:
●PROFINET certificate for software version V2.1.0
●PROFINET IO version V2.2
●Network load Class I
Integration
The following figures show examples of some of the of the integration options of the readers.
Note that in all examples, the connection of the readers RF680R and RF685R can be via a
SIMATIC controller both via Industrial Ethernet / PROFINET and via PROFIBUS.
Figure 3-1 RF650R reader in an IT environment
Figure 3-2 RF680R reader in an automation environment (PROFINET)
Figure 3-3 RF680R reader in an automation environment (PROFIBUS)

Description
3.2 User-specific procedures
SIMATIC RF650R/RF680R/RF685R
14 Configuration Manual, 10/2015, C79000-G8976-C386-03
Figure 3-4 RF685R in an IT environment, without external antenna
All 3 readers can be integrated in an IT environment (XML). The RF68xR readers can be
integrated both in an IT and in an automation environment (S7).
The RF685R reader can also be operated without external antennas.
3.2
User-specific procedures
The SIMATIC RF650R, RF680R or RF685R UHF readers are preconfigured when shipped
and can be put into operation without any further configuration. When shipped from the
factory, the readers are preconfigured as follows:
●First antenna connector set
●Transmit power: 20 dBm
●IP address:
–RF650R: 192.168.0.254
–RF680R/RF685R: DHCP
As described in the previous section, the SIMATIC UHF readers RF650R, RF680R and
RF685R are designed for different environments and requirements.
If you operate the RF680R and RF685R readers in an automation environment, they are
configured and programmed from the perspective of an S7 user. Integration in third-party
controllers is, of course, also possible. If you operate the RF650R, RF680R and RF685R
readers in an XML environment, they are configured and programmed from the perspective
of an XML user.
If you want to adapt the readers to your requirements, we recommend the following user-
specific procedure:

Description
3.2 User-specific procedures
SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 15
Procedure as S7 user
1. Connect the hardware
You will find information on this in the section "Connect the hardware (Page 19)".
2. Assign the IP address / device name
You will find information on this in the section "Assigning the IP address / device name
with the PST (Page 23)" or "Assigning the IP address / device name with STEP 7
(Page 25)".
3. Configure reader and if applicable communications module
You will find information on this in the section "Configuration via STEP 7 (PROFINET
device) (Page 29)" and "Configuring with the WBM (Page 33)".
4. Configure / program reader commands
You will find information on this in the section "Interface to the SIMATIC controller
(Page 93)".
Procedure as XML user
1. Connect the hardware
You will find information on this in the section "Connect the hardware (Page 19)".
2. Assign the IP address / device name
You will find information on this in the section "Assigning the IP address / device name
with the PST (Page 23)".
3. Configure the reader
You will find information on this in the section "Configuring with the WBM (Page 33)".
4. Program reader commands
You will find information on this in the section "XML interface (Page 139)".
Later in the document, these symbols will help your orientation and will show you whether
the section is of interest to you or not. Only the sections with user-specific content, in other
words content that is tool/interface-specific contain these symbols. Sections without these
symbols are general and relevant for both areas of application.

Description
3.2 User-specific procedures
SIMATIC RF650R/RF680R/RF685R
16 Configuration Manual, 10/2015, C79000-G8976-C386-03

SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 17
Commissioning
4
Note
Commissioning the readers in PROFIBUS operation
You will find information on commissioning the RF680R and RF685R readers via a
communications module (PROFIBUS operation) in the manual of the relevant
communications module.
4.1
Important notes on using the device
Safety notices on the use of the device
The following safety notices must be adhered to when setting up and operating the device
and during all work relating to it such as installation, connecting up, replacing devices or
opening the device.
General notes
WARNING
Safety extra low voltage
The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a
Limited Power Source (LPS). (This does not apply to 100 V ... 240 V devices.)
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1
must be connected to the power supply terminals. The power supply unit for the equipment
power supply must comply with NEC Class 2, as described by the National Electrical Code
(r) (ANSI / NFPA 70).
There is an additional requirement if devices are operated with a redundant power supply:
If the equipment is connected to a redundant power supply (two separate power supplies),
both must meet these requirements.
WARNING
Opening the device
D not open the device when energized.

Commissioning
4.1 Important notes on using the device
SIMATIC RF650R/RF680R/RF685R
18 Configuration Manual, 10/2015, C79000-G8976-C386-03
NOTICE
Alterations not permitted
Alterations to the devices are not permitted. If this is not adhered to, the radio approvals,
the relevant country approvals (e.g. CE or FCC) and the manufacturer's guarantee are
invalidated.
Overvoltage protection
NOTICE
Protection of the external 24 VDC voltage supply
If the module is supplied via extensive 24 V supply lines or networks, interference by strong
electromagnetic pulses on the supply lines is possible, e.g. from lightning or the switching
of large loads.
The connector for the 24 VDC external power supply is not protected against strong
electromagnetic pulses. Make sure that any cables liable to lightning strikes are fitted with
suitable overvoltage protection.
Repairs
WARNING
Repairs only by authorized qualified personnel
Repairs may only be carried out by authorized qualified personnel. Unauthorized opening of
and improper repairs to the device may result in substantial damage to equipment or risk of
personal injury to the user.

Commissioning
4.2 Connect the hardware
SIMATIC RF650R/RF680R/RF685R
Configuration Manual, 10/2015, C79000-G8976-C386-03 19
4.2
Connect the hardware
Prior to installation and commissioning
NOTICE
Read the manual of the SIMATIC controller you using
Prior to installation, connecting up and commissioning, read the relevant sections in the
manual of the SIMATIC controller you are using. When installing and connecting up, keep
to the procedures described in the manual.
NOTICE
Installation/removal with the power off
Wire up the PC or SIMATIC controller and modules to be connected only when the power is
off. Make sure that the power supply is turned off when installing/uninstalling the devices.
Procedure
Follow the steps below to connect a reader via Ethernet/PROFINET:
1. Install the reader.
2. Connect the reader to the PC or the SIMATIC controller using an Ethernet cable.
–For the Ethernet connection to the RF650R reader, use a connecting cable with an
RJ-45 plug.
–For the PROFINET connection of the RF680R/RF685R reader, use a connecting
cable with an M12 plug (4-pin).
3. If necessary, connect the reader to one or more external antennas.
4. Connect the reader to the power supply using the connecting cable.
The reader is ready for operation when the "R/S" LED is lit/flashes green. If the "R/S" LED is
flashing, the reader is waiting for a connection. If the "R/S" LED is lit constantly, the reader is
connected to the controller or PC.

Commissioning
4.2 Connect the hardware
SIMATIC RF650R/RF680R/RF685R
20 Configuration Manual, 10/2015, C79000-G8976-C386-03
Pre-assembled cables therefore permit the ideal and simple connection of the reader. You
will find more information on the cables and wide-range power supply unit in the catalog "ID
10
(https://w3app.siemens.com/mcms/infocenter/content/en/Seiten/order_form.aspx?nodeKey=
key_9180440&infotype=1)".
Table 4- 1 Interfaces and antenna connectors of the readers
Picture
Description
Interfaces of the RF680R/RF685R readers
①Digital I/O interface (M12, 12-pin)
②Power supply 24 VDC and RS-422 (M12, 8-
pin)
③Ethernet interface, TCP/IP (M12, 4-pin)
④
Ethernet interface, TCP/IP (M12, 4-pin)
Interfaces of the RF650R reader
①Digital I/O interface (M12, 12-pin)
②Power supply 24 VDC and RS-422 (M12, 8-
pin)
③Ethernet interface, TCP/IP (RJ-45 , 8-pin)
Antenna connectors of the RF650R/RF680R
readers
4 x antenna connectors for external antennas
(RP-TNC)
Antenna connector of the RF685R reader
1 x antenna connector for external antenna
(RP-TNC)
For detailed information on mounting the readers as well as ordering data of the readers and
cables, refer to the section "SIMATIC RF600 System Manual
(https://support.industry.siemens.com/cs/ww/en/view/22437600)".