Siemens SIMATIC HMI TP 070 Technical Document

Preface, Contents
Introduction 1
Functionality 2
Commissioning 3
Operating the TP 070 4
Operation of Screen Objects 5
System Settings 6
Communication 7
Installation 8
Unit Description 9
Maintenance/Upkeep 10
Operating System Update 11
Appendices A
D
Glossary, Index
Release 03/00
6AV6591–1DC01–1AB0
Touch Panel
TP 070
Equipment Manual
SIMATIC HMI

Index-2 TP070EquipmentManual
Release03/00
!Warning
indicatesthat death, severe personalinjury or substantial propertydamage canresult if proper precau-
tions are not taken.
!Caution
indicatesthat minor personal injury or property damagecan result if proper precautionsare not taken.
Note
drawsyour attention to particularlyimportant information on theproduct, handling the product,or to a
particularpartofthedocumentation.
Qualified Personnel
Equipmentmay be commissionedand operated onlyby qualifiedpersonnel.Qualifiedpersonnelwithin
the meaning of the safety notices in this manual are persons who are authorized to commission, ground
andidentifyequipment, systems and circuitsinaccordance with safety engineeringstandards.
Correct Usage
Notethefollowing:
!Warning
Theequipment maybe used only for the applications stipulated in the catalog and in the technical descrip-
tionandonly in conjunction with otherequipmentand components recommended or approvedbySie-
mens.
Startup must not take place until it is established that the machine, which is to accommodate this compo-
nent,isinconformitywiththeguideline89/392/EEC.
Faultlessandsafe operation of the product presupposespropertransportation,properstorage,erection
andinstallationas well as careful operation andmaintenance.
Trademarks The registered trademarks of Siemens AG are listed in the Preface.
Someof the other designations usedin these documentsare also registered trademarks; theowner’s
rights may be violated if they are used be third parties for their own purposes.
Impressum Editorand Publisher: A&D PT1.
Safety Guidelines
This manual contains notices which you should observe to ensure your own personal safety, as well as to
protecttheproduct and connected equipment.These notices are highlightedin the manual byawarning
triangle and are marked as follows according to the level of danger:
We have checked the contents of this manual for agreement with the hard-
wareandsoftwaredescribed.Sincedeviationscannotbeprecludedentirely,
we cannot guarantee full agreement. However, the data in this manual are
reviewed regularly and any necessary corrections included in subsequent
editions.Suggestions for improvement are welcomed.
Disclaimer of LiabilityCopyright Siemens AG 2000 All rights reserved
The reproduction, transmission or use of thisdocument or its contentsis not
permitted without express written authority. Offenders will be liable for
damages.Allrights,includingrightscreatedbypatentgrantorregistration of
an utility model or design, are reserved.
Siemens AG
Automation & Drives
SIMATIC Human Machine Interface
Postfach 4848, D-90327 Nürnberg SiemensAG 2000
Technical data subject to change.
SiemensAktiengesellschaft Order no: 6AV6591–1DC01–1AB0

i
TP070EquipmentManual
Release03/00
Preface
This manual
The TP 070 equipment manual is part of the SIMATIC HMI documentation. It
provides operation, installation, configuration and system personnel with
information concerning installation, functionality, operation and technical design of
the TP 070.
An overview of the entire SIMATIC HMI documentation is provided in appendix D.
Organization of the manual
The TP 070 equipment manual is organized into the following chapters:
Chapter Contents
1 - 2 Overview of features and functional scope of the TP 070.
3 - 7 Commissioning, operation, system settings and communication.
8 - 10 Mechanical and electrical installation, unit description, as well as
maintenance and upkeep of the TP 070.
11 Information on the operating system update.
Appendix Technical Data
Interface Assignments
ESD Guidelines
SIMATIC HMI Documentation

Preface
ii TP070EquipmentManual
Release03/00
Conventions
The following conventions are used throughout this manual:
Motor off Text in the operating unit display is presented in this
typewriter font.
Tag Symbolic names representing tag values on the screen are
presented in this italic typewriter font.
Screens Functions available for selection are presented in this italic
font.
ESC The names of keys and buttons are displayed in a different
font.
History
The various releases of this manual correspond to the following versions of the
STEP 7-Micro/WIN 32 and STEP 7-Micro/WIN 32 Toolbox configuration software:
Release Comment Micro/WIN 32
version Micro/WIN 32 Toolbox
version
03/00 First release of the TP 070
equipment manual. From Version 3.1 From Version 1.0
Trademarks
The following names are registered trademarks of the Siemens AG:
SSIMATICR
SSIMATIC HMIR
SHMIR
SProToolR
SProTool/LiteR
SProTool/ProR
SSIMATIC Multi PanelR
SSIMATIC Multifunctional PlatformR
SMP 270R
SProAgentR
Other support
In the case of technical queries, please contact the Siemens representatives in the
subsidiaries and branches responsible for your area.

Preface
iii
TP070EquipmentManual
Release03/00
SIMATIC Customer Support Hotline
Available worldwide, at all times:
Johnson City
Nuernberg
Singapur
SIMATIC Basic Hotline
Nuernberg Johnson City Singapur
SIMATIC BASIC Hotline SIMATIC BASIC Hotline SIMATIC BASIC Hotline
Localtime Mo - Fr 7:00 to 17:00 Localtime Mo - Fr 8:00 to 19:00 Localtime Mo - Fr 8:30 to 17:30
Telephone: [phone] Telephone: [phone] Telephone: [phone]
Fax: [phone] Fax: [phone] Fax: [phone]
E-Mail: simatic.support@
nbgm.siemens.de E-Mail: simatic.hotline@ sea.siemens.com E-Mail: simatic.hotline@ sae.siemens.com.sg
SIMATIC Premium Hotline
(charged,onlywith SIMATICCard)
Time: Mo - Fr 0:00 to 24:00
Telephone: [phone]
Fax: [phone]

Preface
iv TP070EquipmentManual
Release03/00
SIMATIC Customer Online Services
SIMATIC Customer Support offers comprehensive additional information
concerning SIMATIC products through its Online services as follows:
Up-to-date general information is provided
– in Internet under http://www.ad.siemens.de/simatic
– via the Fax-Polling under 08765–93 02 77 95 00
Up-to-date product information and downloads for practical use can be found:
– in Internet under http://www.ad.siemens.de/support/html–00/
Abbreviations
The abbreviations used in this equipment manual have the following meaning:
CCFL Cold Cathode Fluorescence Lamp
CPU Central Processing Unit
ESD Electrostatic Sensitive Device
HMI Human Machine Interface
IF Interface
LCD Liquid Crystal Display
MPI Multipoint Interface (SIMATIC S7)
PC Personal Computer
PLC Programmable Logic Control
PPI Point to Point Interface (SIMATIC S7)
PU Programming Unit
RISC Reduced Instruction Set Computing
STN Super Twisted Nematic
TP Touch Panel
A list of all the specialist terms together with their explanations is provided in the
glossary at the end of this manual.

v
TP070EquipmentManual
Release03/00
Contents
1 Introduction 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Functionality 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 Commissioning 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 Initial Startup 3-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Recommissioning 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Test Configuration 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Operating the TP 070 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Operating Touch Elements 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 Entering Values 4-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 Operating Screens 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Operation of Screen Objects 5-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Overview of Screen Objects 5-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Status Button 5-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 System Settings 6-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Setting an Operating Mode 6-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Screen Settings 6-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Deactivate Screen 6-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 Communication Management for SIMATIC S7 7-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Basic Methods of Functioning 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Connection to S7-200 via MPI 7-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3 Optimization 7-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Installation 8-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 Mechanical Installation 8-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2 Electrical Installation 8-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.1 Connect configuration computer 8-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.2 Connect PLC 8-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 Unit Description 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1 Dimensions 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.2 Connection Elements 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3 Communication Options 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Contents
vi TP070EquipmentManual
Release03/00
10 Maintenance/Upkeep 10-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 Operating System Update 11-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix
A Technical Data A-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B Interface Assignment B-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C ESD Guidelines C-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D SIMATIC HMI Documentation D-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1-1
TP070EquipmentManual
Release03/00
Introduction
Use of the TP 070
The TP 070 has been conceived as a low end unit for the SIMATIC S7-200. It is a
touch panel in the SIMATIC HMI product range based on the MicrosoftWindows
CE operating system.
The TP 070 can be used to perform all basic functions. It is equipped with one
interface for use with MPI. The unit memory is designed for smaller configurations.
The objects used for a configuration can be inputs, outputs, buttons, bar graphs
and graphics.
Area of use of the TP 070
The TP 070 has been conceived for machine operation and monitoring. It provides
a realistic representation of the machine or system to be monitored. Its area of use
includes implementation in machine and apparatus construction as well as in the
packing and electronics industry.
The high degree of protection (IP65 on the front side) and non-implementation of
moving storage media, such as hard disks and floppy disks, ensure the TP 070 is
also suitable for use in rough industrial environments and directly on site on the
respective machine.
The TP 070 can be installed in switching cabinets and operating consoles.
Due to the fact that the TP 070 is equipped with high performance basic hardware
and has a minimum installation depth means that it fulfills all the requirements for
operation in the vicinity of the machine.
1

Introduction
1-2 TP070EquipmentManual
Release03/00
Easy to operate and observe
The TP 070 enables operating statuses and current process values concerning a
connected PLC to be displayed textually or graphically and the relevant machine or
system to be easily monitored and operated. Display and operation of the TP 070
can be adapted optimally for the respective process requirements by using the
STEP 7-Micro/WIN 32 (from version 3.1) and STEP 7-Micro/WIN 32 Toolbox (from
version 1.0) configuration software.
The TP 070 can be used to:
control and monitor the process intuitively. Setpoint values or control element
settings, for instance, can be modified by entering values or touching configured
buttons;
display processes, machines and systems graphically;
visualize process tags, e.g. in output fields, status displays or bar graphs;
intervene directly in the operation by means of the touch–sensitive screen.

Introduction
1-3
TP070EquipmentManual
Release03/00
Operating unit configuration (principles)
Graphics, texts and operating and display elements which need to be represented
on the operating unit must first be created on a configuration computer (PC or PU)
using the configuration software. The configuration computer must be connected to
the operating unit in order to download the project to the operating unit (refer to
“Configuration phase” in figure 1-1).
Once the project has been successfully downloaded, connect the operating unit to
the PLC. The operating unit can then communicate with the PLC and respond
according to the information configured for running the program in the PLC (refer to
“Process control phase” in figure 1-1).
Createprojectdata
Storeproject data
Downloadprojectdata
ConnectedtoPLC
Configurationphase
Process control phase
PC/PU
PLC
Operating unit
TP
Testproject
Figure 1-1 Configuration and process control phases

Introduction
1-4 TP070EquipmentManual
Release03/00
Overview of the TP 070
Overview: Model TP 070
Processor Type 32 bit RISC
Clock frequency 66 MHz
Configuration
memory Capacity 128 kB
Software Operating system MicrosoftR WindowsR CE
Interfaces Serial interface to connect PLC,
PC/PU 1 ×RS485
Display Type STN LCD/Blue mode
Active screen area
(B ×H) in mm 116 ×87 (5.7’’)
Resolution (pixels) 320 ×240
Monochrome 4–level
Back–lighting CCFL tube
Half Brightness Life1) approx. (h) 50,000
1) Refer to the Glossary for a definition.
Further information
Detailed information on the technical data of the operating unit is provided in
appendix A of this manual.
Information concerning configuration of the operating unit is provided in the
Micro/WIN user guide or Micro/WIN online help.
Connection of the operating unit to the PLC is described in chapter 7.

2-1
TP070EquipmentManual
Release03/00
Functionality
The table below summarizes the functional scope of the operating unit. The values quoted are
the maximum values which can be managed by the operating unit. The values are limited by the
size of the memory used.
Function Comment
Screens View 4
Screen objects Output field
Input field
Text
Graphics
State button
Bar
Screen settings Contrast 4
Touch calibration 4
Communication SIMATIC S7-200
MPI (to 19.2 kbits/s) 4
2

Functionality
2-2 TP070EquipmentManual
Release03/00

3-1
TP070EquipmentManual
Release03/00
Commissioning
In this chapter
This chapter provides information on:
starting up the operating unit for the first time (page 3-2)
restarting the operating unit (page 3-3)
testing a configuration (page 3-3)
3

Commissioning
3-2 TP070EquipmentManual
Release03/00
3.1 InitialStartup
Procedure
When the operating unit is started up for the first time, there is no configuration
loaded. Proceed as follows, observing the sequence, in order to download a
configuration from the configuration computer to the operating unit which is
necessary to put the unit into service:
Step Procedure
1Connect the operating unit interface IF1B (RS485) to the configuration computer
using a PC/PPI cable.
2Switch on the power supply for the operating unit.
Since no configuration has been loaded at this point, the operating unit
automatically switches to Download mode. The operating unit displays the
message Connecting to host until it receives data from the configuration
computer or the button Cancel is pressed.

Commissioning
3-3
TP070EquipmentManual
Release03/00
3.2 Recommissioning
Purpose
Following a restart, the configuration in the operating unit is replaced by a different
one. The new configuration is downloaded from the configuration computer to the
operating unit.
The following options are available for downloading a configuration:
Start downloading manually during the operating unit startup phase
Start downloading via a correspondingly configured operating element while the
operating unit is in operation (refer to the chapter 6.1)
Start downloading manually during the operating unit initialization phase
Step Procedure
1Connect the operating unit interface IF1B (RS485) to the configuration computer
using a PC/PPI cable.
2Switch on the power supply for the operating unit.
3During the operating unit start–up phase, a menu appears briefly on the screen.
Touch the Download button to set the operating unit to Download mode before it
is initialized.
The operating unit displays the message Connecting to host until it receives
data from the configuration computer or the button Cancel is pressed.
3.3 TestConfiguration
Test with connected PLC
When a PLC is connected it is possible to test the communication between the
operating unit and PLC. This test also determines whether the correct data areas
have been configured.
Check the following configuration elements, for example:
screen selection,
input fields.

Commissioning
3-4 TP070EquipmentManual
Release03/00

4-1
TP070EquipmentManual
Release03/00
Operating the TP 070
In this chapter
This chapter contains information on how to:
operate touch elements (from page 4-2)
enter values (from page 4-4)
operate screens (page 4-6)
Information regarding operation for special screen objects is provided in chapter 5.
4

Operating the TP 070
4-2 TP070EquipmentManual
Release03/00
4.1 Operating Touch Elements
Operating concept
The screen is used to observe the operating status of the machine or system being
monitored and, at the same time, to intervene directly in the process running
simply by touching the buttons and input fields displayed.
Definition
Touch elements are contact-sensitive operating elements provided on the touch
panel screen, such as buttons and input fields. Their operation is basically no
different from pressing conventional keys. Touch elements are operated by
touching them lightly with your finger or a suitable object.
Note
Never use pointed or sharp instruments to operate the Touch Panel to prevent
damage to the plastic surface of the touch screen.
!Caution
Never touch more than one touch panel screen element at a time. If you do, an
unintended action may be initiated.