Siemens SITRANS P User manual

SITRANS P
Pressure transmitter
SITRANS P320/P420 with 4 to 20
mA/HART
Operating Instructions
7MF03..-.....-.... (SITRANS P320)
7MF04..-.....-.... (SITRANS P420)
11/2019
A5E44852162-AC
Getting Started 1
Introduction 2
Safety information 3
Description 4
Installing/mounting 5
Connecting 6
Operating 7
Commissioning 8
Parameter assignment 9
Functional Safety 10
Service and maintenance 11
Diagnostics and
troubleshooting 12
Technical data 13
Dimension drawings 14
Product documentation and
support A
Remote operation B
Checklist for Functional
Safety C
Sealing plug / thread adapter D
Abbreviations E

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E44852162
Ⓟ 10/2019 Subject to change
Copyright © Siemens AG 2019.
All rights reserved

Table of contents
1 Getting Started ...........................................................................................................................................11
1.1 Commissioning the device without display.............................................................................11
1.2 Commissioning the device with display..................................................................................12
2 Introduction.................................................................................................................................................15
2.1 Purpose of this documentation...............................................................................................15
2.2 Scope of validity of this document..........................................................................................15
2.3 Document history ...................................................................................................................15
2.4 Product compatibility ..............................................................................................................16
2.5 Checking the consignment.....................................................................................................16
2.6 Security information ...............................................................................................................16
2.7 Transportation and storage ....................................................................................................17
2.8 Notes on warranty ..................................................................................................................17
3 Safety information.......................................................................................................................................19
3.1 Precondition for use ...............................................................................................................19
3.1.1 Warning symbols on the device .............................................................................................19
3.1.2 Laws and directives................................................................................................................19
3.1.3 Conformity with European directives......................................................................................20
3.1.4 Classification according to the pressure equipment directive ................................................20
3.2 Requirements for special applications ...................................................................................21
3.3 Use in hazardous areas .........................................................................................................21
4 Description..................................................................................................................................................25
4.1 Area of application .................................................................................................................25
4.2 Structure.................................................................................................................................27
4.3 Nameplate layout ...................................................................................................................28
4.4 Functional principle ................................................................................................................30
4.4.1 Electronics..............................................................................................................................31
4.4.2 Measuring cell ........................................................................................................................32
4.4.2.1 Measuring cell for gauge pressure.........................................................................................33
4.4.2.2 Measuring cell for gauge pressure, front-flush membrane.....................................................34
4.4.2.3 Measuring cell for absolute pressure from the gauge pressure series ..................................34
4.4.2.4 Measuring cell for absolute pressure, front-flush membrane .................................................35
4.4.2.5 Measuring cell for absolute pressure from the differential pressure series............................36
4.4.2.6 Measuring cell for differential pressure and flow rate.............................................................37
4.4.2.7 Measuring cell for level ..........................................................................................................38
4.5 System configuration..............................................................................................................38
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 3

4.6 Remote seal and differential pressure flow measuring systems ............................................40
4.6.1 Remote seal ...........................................................................................................................40
4.6.2 Differential pressure - flow measuring systems .....................................................................40
4.6.3 Remote seals and primary element for devices with functional safety...................................41
5 Installing/mounting......................................................................................................................................43
5.1 Basic safety instructions.........................................................................................................43
5.1.1 Installation location requirements...........................................................................................46
5.1.1.1 Use in maritime deployment...................................................................................................46
5.1.2 Proper mounting.....................................................................................................................47
5.2 Installing ................................................................................................................................47
5.2.1 Introduction ............................................................................................................................47
5.2.2 Fastening with the mounting bracket .....................................................................................49
5.2.3 Mounting hygienic version......................................................................................................50
5.3 Installation (level) ...................................................................................................................51
5.3.1 Mounting on the container......................................................................................................52
5.4 Installation with remote seal...................................................................................................54
5.4.1 Remote seal with capillary line...............................................................................................56
5.5 Installing electrical connections and cable entries .................................................................61
5.6 Rotating the display................................................................................................................61
5.7 Rotating the enclosure ...........................................................................................................63
5.8 Removing ...............................................................................................................................64
6 Connecting .................................................................................................................................................65
6.1 Basic safety instructions.........................................................................................................65
6.2 Connecting the device............................................................................................................68
6.2.1 Opening the device ................................................................................................................68
6.2.2 Connecting the device............................................................................................................69
6.2.3 Closing the device..................................................................................................................71
6.3 Connect the Han cable socket to the cable............................................................................71
6.4 Connect M12 cable socket to the cable .................................................................................72
7 Operating....................................................................................................................................................75
7.1 Buttons ...................................................................................................................................75
7.2 Operating the device with display ..........................................................................................76
7.2.1 Navigating in the views ..........................................................................................................76
7.2.2 Measurement view .................................................................................................................76
7.2.2.1 Display of measured values ...................................................................................................77
7.2.2.2 Navigating in the measurement view .....................................................................................78
7.2.3 Parameter view ......................................................................................................................78
7.2.3.1 List of parameters on the display ...........................................................................................78
7.2.3.2 Navigating in the parameter view...........................................................................................80
7.2.4 Edit view.................................................................................................................................80
7.2.4.1 Changing parameter values ...................................................................................................81
7.2.5 Symbols for information messages ........................................................................................81
7.3 Remote operation...................................................................................................................81
Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
4Operating Instructions, 11/2019, A5E44852162-AC

7.4 Locking the device .................................................................................................................82
7.4.1 Enable write protection with jumper .......................................................................................82
7.4.2 Enable user PIN .....................................................................................................................83
7.4.3 Enabling button lock...............................................................................................................84
8 Commissioning ...........................................................................................................................................87
8.1 Basic safety instructions.........................................................................................................87
8.2 Switching on the supply voltage.............................................................................................88
8.3 Commissioning the device without display.............................................................................89
8.4 Commissioning the device with display..................................................................................90
8.5 Application examples .............................................................................................................92
8.5.1 Gauge pressure, absolute pressure from differential pressure series, and absolute
pressure from gauge pressure series ....................................................................................92
8.5.1.1 Commissioning in gaseous environments..............................................................................92
8.5.1.2 Commissioning with steam or liquid.......................................................................................93
8.5.2 Differential pressure and flow rate .........................................................................................94
8.5.2.1 Commissioning in gaseous environments..............................................................................94
8.5.2.2 Commissioning for liquids ......................................................................................................96
8.5.2.3 Commissioning with vapor .....................................................................................................98
9 Parameter assignment .............................................................................................................................101
9.1 Overview of parameters and functions.................................................................................101
9.2 Parameter assignment over device with display ..................................................................106
9.2.1 Pressure units [01] ...............................................................................................................106
9.2.1.1 Display of the pressure units................................................................................................107
9.2.1.2 Setting the pressure units ....................................................................................................107
9.2.2 Set lower range value [02]/Set upper range value [03] ........................................................108
9.2.2.1 Set lower range value parameter [02] ..................................................................................108
9.2.2.2 Set upper range value parameter [03] .................................................................................108
9.2.2.3 Set lower range value/upper range value (without pressure available) ...............................109
9.2.3 Damping value [04] ..............................................................................................................110
9.2.3.1 Set damping value ...............................................................................................................110
9.2.4 Application [05].....................................................................................................................110
9.2.4.1 Pressure measurement........................................................................................................112
9.2.4.2 Level measurement..............................................................................................................113
9.2.4.3 Volume and mass flow measurements ................................................................................115
9.2.4.4 Volume measurement ..........................................................................................................118
9.2.4.5 Set application......................................................................................................................119
9.2.5 Application point [06]............................................................................................................119
9.2.6 Zero point adjustment [07] ...................................................................................................119
9.2.6.1 Adjusting zero point (gauge pressure) .................................................................................120
9.2.6.2 Adjusting the zero point (differential pressure).....................................................................121
9.2.6.3 Adjusting zero point (absolute pressure)..............................................................................121
9.2.7 Apply lower range value [08]/Apply upper range value [09].................................................122
9.2.7.1 Apply lower range value parameter [08] ..............................................................................122
9.2.7.2 Apply upper range value parameter [09]..............................................................................122
9.2.7.3 Apply lower range value/upper range value (with pressure present) ...................................122
9.2.8 Select fault current [10] ........................................................................................................124
9.2.9 Lower fault current [11] ........................................................................................................124
Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 5

9.2.10 Upper fault current [12] ........................................................................................................125
9.2.11 Lower saturation limit [13] ....................................................................................................125
9.2.12 Upper saturation limit [14] ....................................................................................................126
9.2.13 SV selection [15] ..................................................................................................................127
9.2.14 Units [16] ..............................................................................................................................127
9.2.14.1 Level units [16] .....................................................................................................................128
9.2.14.2 Volume units [16] .................................................................................................................128
9.2.14.3 Volume flow units [16] ..........................................................................................................128
9.2.14.4 Mass flow units [16]..............................................................................................................129
9.2.15 Temperature units [17] .........................................................................................................130
9.2.16 Lower scaling point [18] .......................................................................................................130
9.2.16.1 Set lower scaling point .........................................................................................................131
9.2.17 Upper scaling point [19] .......................................................................................................132
9.2.17.1 Set upper scaling point.........................................................................................................132
9.2.18 Low flow cut-off [20] .............................................................................................................132
9.2.19 Vessel dimension A [21].......................................................................................................133
9.2.20 Vessel dimension L [22] .......................................................................................................134
9.2.21 Button lock [23] ....................................................................................................................134
9.2.21.1 Enabling button lock.............................................................................................................134
9.2.21.2 Disabling button lock ............................................................................................................135
9.2.22 Change user PIN [24]...........................................................................................................135
9.2.23 Recovery ID [25] ..................................................................................................................136
9.2.23.1 Display Recovery ID.............................................................................................................137
9.2.24 PIN recovery [26] .................................................................................................................137
9.2.24.1 Recovering the user PIN ......................................................................................................137
9.2.25 User PIN [27]........................................................................................................................138
9.2.25.1 Enable user PIN ...................................................................................................................139
9.2.25.2 Disable user PIN ..................................................................................................................139
9.2.26 Active device mode [28] .......................................................................................................140
9.2.27 Functional Safety [29] ..........................................................................................................140
9.2.28 Display test [30]....................................................................................................................141
9.2.29 Loop test [31] .......................................................................................................................141
9.2.29.1 Loop test with preset loop current value ..............................................................................141
9.2.29.2 Loop test with user defined loop current value.....................................................................142
9.2.30 Start view [32] ......................................................................................................................142
9.2.31 Pressure reference [33]........................................................................................................143
9.2.32 Identify the device [34] .........................................................................................................143
9.2.33 Reset [35].............................................................................................................................143
9.2.33.1 Reset to sensor calibration...................................................................................................144
9.2.33.2 Reset DAC trim to the factory setting...................................................................................144
9.2.33.3 Restore ordered configuration..............................................................................................144
9.2.33.4 Restore factory settings .......................................................................................................144
9.2.34 Overload behavior [36].........................................................................................................145
9.3 Parameter assignment over remote operation.....................................................................145
9.3.1 Introduction ..........................................................................................................................145
9.3.2 Quick start ............................................................................................................................146
9.3.3 Identification .........................................................................................................................146
9.3.4 Simulation ............................................................................................................................147
9.3.4.1 Simulate constant pressure values .....................................................................................147
9.3.4.2 Simulate ramp function ........................................................................................................148
9.3.4.3 Simulate diagnostics ............................................................................................................148
9.3.5 Customized characteristic curve ..........................................................................................149
Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
6Operating Instructions, 11/2019, A5E44852162-AC

9.3.5.1 Introduction ..........................................................................................................................149
9.3.5.2 "Custom units" parameter ....................................................................................................150
9.3.5.3 Set customized characteristic curve.....................................................................................150
9.3.6 Sensor calibration ................................................................................................................151
9.3.7 Digital-to-analog converter trim (DAC trim) ..........................................................................152
9.3.8 Diagnostics functions ...........................................................................................................154
9.3.8.1 Limit monitoring and event counter ......................................................................................154
9.3.8.2 Trend log ..............................................................................................................................157
9.3.8.3 Operating hours counter ......................................................................................................158
10 Functional Safety......................................................................................................................................159
10.1 Safety concept .....................................................................................................................159
10.1.1 Random and systematic errors ............................................................................................159
10.1.2 SIL-compliant product version..............................................................................................159
10.1.3 Safety function .....................................................................................................................160
10.1.3.1 Device states........................................................................................................................162
10.1.3.2 Safety characteristic values .................................................................................................162
10.1.4 Operating modes of the device ............................................................................................163
10.1.5 Device mode ........................................................................................................................163
10.1.5.1 Validation .............................................................................................................................164
10.1.5.2 Safety-related parameters....................................................................................................165
10.1.5.3 Device mode "Functional Safety enabled" ...........................................................................165
10.2 Enabling Functional Safety ..................................................................................................166
10.2.1 Enabling Functional Safety over device with display ...........................................................167
10.2.2 Enabling Functional Safety over remote operation ..............................................................170
10.3 Acknowledging safety-related errors....................................................................................174
10.3.1 "Safety critical error" device mode .......................................................................................174
10.3.2 Acknowledging safety-related errors via remote operation ..................................................175
10.4 Disabling Functional Safety over device with display...........................................................176
10.5 Disabling Functional Safety over remote operation .............................................................177
10.6 Proof test..............................................................................................................................178
10.6.1 Intervals and rules for proof test...........................................................................................178
10.6.2 Documenting a proof test .....................................................................................................179
10.7 Repair and service ...............................................................................................................179
11 Service and maintenance .........................................................................................................................181
11.1 Basic safety instructions.......................................................................................................181
11.2 Cleaning ...............................................................................................................................182
11.2.1 Cleaning the enclosure ........................................................................................................182
11.2.2 Servicing the remote seal measuring system ......................................................................182
11.3 Maintenance and repair work...............................................................................................182
11.3.1 Checking the seals...............................................................................................................184
11.3.2 Check cable glands..............................................................................................................185
11.3.3 Replacing spare parts ..........................................................................................................185
11.3.3.1 Replacing electrical connections and cable entries .............................................................185
11.3.3.2 Replacing the display ...........................................................................................................185
11.3.3.3 Replacing the termination board ..........................................................................................187
11.4 Return procedure .................................................................................................................188
Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 7

11.5 Disposal ...............................................................................................................................188
12 Diagnostics and troubleshooting ..............................................................................................................189
12.1 Device status symbols .........................................................................................................189
12.2 Diagnostic messages ...........................................................................................................192
12.3 Troubleshooting ...................................................................................................................197
13 Technical data ..........................................................................................................................................199
13.1 Input .....................................................................................................................................199
13.1.1 Gauge pressure ...................................................................................................................199
13.1.2 Gauge pressure with front-flush diaphragm .........................................................................200
13.1.3 Gauge pressure from the differential pressure series ..........................................................201
13.1.4 Absolute pressure from the gauge pressure series .............................................................202
13.1.5 Absolute pressure with front-flush diaphragm......................................................................203
13.1.6 Absolute pressure from the differential pressure series.......................................................204
13.1.7 Differential pressure and flow...............................................................................................206
13.1.8 Level.....................................................................................................................................207
13.2 Measuring accuracy of SITRANS P320 ...............................................................................208
13.2.1 Reference conditions ...........................................................................................................208
13.2.2 Effect of auxiliary power supply............................................................................................208
13.2.3 Gauge pressure ...................................................................................................................208
13.2.4 Gauge pressure from the differential pressure series ..........................................................210
13.2.5 Absolute pressure from gauge and differential pressure series...........................................211
13.2.6 Absolute pressure with front-flush diaphragm......................................................................212
13.2.7 Gauge pressure with front-flush diaphragm .........................................................................213
13.2.8 Differential pressure and flow...............................................................................................214
13.2.9 Level.....................................................................................................................................217
13.3 Measuring accuracy of SITRANS P420 ...............................................................................218
13.3.1 Reference conditions ...........................................................................................................218
13.3.2 Effect of auxiliary power supply............................................................................................218
13.3.3 Gauge pressure ...................................................................................................................218
13.3.4 Gauge pressure from the differential pressure series .........................................................219
13.3.5 Absolute pressure from gauge and differential pressure series...........................................221
13.3.6 Absolute pressure with front-flush diaphragm......................................................................222
13.3.7 Gauge pressure with front-flush diaphragm .........................................................................223
13.3.8 Differential pressure and flow...............................................................................................223
13.3.9 Level.....................................................................................................................................227
13.4 Output ..................................................................................................................................228
13.5 Operating conditions ............................................................................................................228
13.6 Vibration resistance..............................................................................................................233
13.7 Construction .........................................................................................................................234
13.8 Torques ................................................................................................................................238
13.9 Display, keys and auxiliary power ........................................................................................238
13.10 Certificates and approvals....................................................................................................239
Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
8Operating Instructions, 11/2019, A5E44852162-AC

14 Dimension drawings .................................................................................................................................243
14.1 SITRANS P320/P420 for gauge pressure and absolute pressure from the gauge
pressure series.....................................................................................................................243
14.2 SITRANS P320/P420 for differential pressure, gauge pressure, flow and absolute
pressure from the differential pressure series......................................................................245
14.3 SITRANS P 320/P420 for level ............................................................................................247
14.4 SITRANS P320/P420 (front-flush) .......................................................................................248
14.4.1 Note 3A and EHDG..............................................................................................................249
14.4.2 Connections as per EN and ASME ......................................................................................249
14.4.3 F&B and pharma flange .......................................................................................................250
14.4.4 PMC Style ............................................................................................................................254
14.4.5 Special connections .............................................................................................................255
A Product documentation and support.........................................................................................................257
A.1 Product documentation ........................................................................................................257
A.2 Technical support.................................................................................................................258
B Remote operation .....................................................................................................................................259
B.1 SIMATIC PDM......................................................................................................................259
B.1.1 Overview SIMATIC PDM......................................................................................................259
B.1.2 Check SIMATIC PDM version..............................................................................................259
B.1.3 Deactivate buffers when connecting via serial modem ........................................................260
B.1.4 Updating the Electronic Device Description (EDD) ..............................................................261
C Checklist for Functional Safety .................................................................................................................263
D Sealing plug / thread adapter ...................................................................................................................267
D.1 Intended use of accessory part ............................................................................................267
D.2 Safety instructions for accessory part ..................................................................................267
D.3 Technical specifications of accessory part...........................................................................268
D.4 Dimensional drawings for accessory part ............................................................................269
E Abbreviations............................................................................................................................................271
Glossary ...................................................................................................................................................273
Index.........................................................................................................................................................277
Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 9

Table of contents
SITRANS P320/P420 with 4 to 20 mA/HART
10 Operating Instructions, 11/2019, A5E44852162-AC

Getting Started 1
1.1 Commissioning the device without display
Introduction
In this section, you will learn how to commission the device step-by-step.
Before you start, please read the following safety information:
●General safety information (Page 19)
● Basic safety information: Installing/mounting (Page 43)
● Basic safety information: Connecting (Page 65)
● Basic safety information: Commissioning (Page 87)
Read the entire device manual in order to achieve the optimum performance of the device.
Procedure
1. Mount the device.
Installing (Page 47)
Installation (level) (Page 51)
2. Connect the device.
Connecting the device (Page 68)
3. Switch on the supply voltage.
Switching on the supply voltage (Page 88)
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 11

4. Open the cover of the buttons:
Figure 1-1 Top view
5. Operate the buttons as follows:
Apply lower range value (with pressure applied) Hold down the button for 3 seconds.
Apply upper range value (with pressure applied) Hold down the button for 3 seconds.
Zero point adjustment Hold down the buttons and for 3 seconds.
Set Upper fault current Hold down the button for 3 seconds.
Set Lower fault current Hold down the button for 3 seconds.
Further functions are available via remote operation (e.g. SIMATIC PDM).
1.2 Commissioning the device with display
Introduction
In this section, you will learn how to commission the device step-by-step.
Before you start, please read the following safety information:
●General safety information (Page 19)
● Basic safety information: Installing/mounting (Page 43)
● Basic safety information: Connecting (Page 65)
● Basic safety information: Commissioning (Page 87)
Read the entire device manual in order to achieve the optimum performance of the device.
Getting Started
1.2 Commissioning the device with display
SITRANS P320/P420 with 4 to 20 mA/HART
12 Operating Instructions, 11/2019, A5E44852162-AC

Procedure
1. Mount the device.
Installing (Page 47)
Installation (level) (Page 51)
2. Connect the device.
Connecting the device (Page 68)
3. Switch on the supply voltage.
Switching on the supply voltage (Page 88)
4. Open the cover of the buttons:
Figure 1-2 Top view
5. Set the measuring range.
Set lower range value/upper range value (without pressure available) (Page 109)
Apply lower range value/upper range value (with pressure present) (Page 122)
6. Set the pressure unit.
Setting the pressure units (Page 107)
7. Set the application of your device.
Set application (Page 119)
8. Set the scaling points.
Set lower scaling point (Page 131)
Set upper scaling point (Page 132)
9. Set the zero point.
Adjusting zero point (gauge pressure) (Page 120)
Adjusting the zero point (differential pressure) (Page 121)
Adjusting zero point (absolute pressure) (Page 121)
10.Lock the device.
Locking the device (Page 82)
11.Enable Functional Safety (for devices with Functional Safety).
Enabling Functional Safety over device with display (Page 167)
You can find additional functions in the section Parameter assignment (Page 101)
Getting Started
1.2 Commissioning the device with display
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 13

See also
Diagnostics and troubleshooting (Page 189)
Getting Started
1.2 Commissioning the device with display
SITRANS P320/P420 with 4 to 20 mA/HART
14 Operating Instructions, 11/2019, A5E44852162-AC

Introduction 2
2.1 Purpose of this documentation
These instructions contain all information required to commission and use the device. Read the
instructions carefully prior to installation and commissioning. In order to use the device
correctly, first review its principle of operation.
The instructions are aimed at persons mechanically installing the device, connecting it
electronically, configuring the parameters and commissioning it, as well as service and
maintenance engineers.
2.2 Scope of validity of this document
Variant SITRANS P320 mA/HART SITRANS P420 mA/HART
Gauge pressure 7MF0300 7MF0400
Gauge pressure from the differential
pressure series
7MF0310 7MF0410
Absolute pressure from the gauge pres‐
sure series
7MF0320 7MF0420
Absolute pressure from the differential
pressure series
7MF0330 7MF0430
Differential pressure and flow rate,
PN 160 (MAWP 2320 psi)
7MF0340 7MF0440
Differential pressure and flow rate, PN
420 (MAWP 6092 psi)
7MF0350 7MF0450
Level 7MF0360 7MF0460
2.3 Document history
The overview below summarizes the most important changes in the documentation when
compared to the previous edition.
Edition Note
11/2019 ● Changes for FW1.01.00 HART device revision 7
●Section Technical data (Page 199) updated.
09/2018 ● Section Replacing spare parts (Page 185) added.
● Basic safety instructions in the sections Use in hazardous areas (Page 21),
Installing/mounting (Page 43), Connecting (Page 65) updated.
● Section Connecting the device (Page 68) updated.
● Section Parameter assignment over remote operation (Page 145) updated.
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 15

2.4 Product compatibility
The following table describes the compatibility between the edition of this manual, the device
revision, the engineering system and the associated EDD.
Edition Comments Product compatibility Compatibility with device integra‐
tion package
11/2019 New device
features
HART 7
FW: 1.01.00 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher
AMS Device Manager V13 or high‐
er
DTM Pactware V4.1 SP4
FC475 V3.9 or higher
09/2018 Manual re‐
vised
HART 7
FW: 1.00.08 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher
AMS Device Manager V13 or high‐
er
DTM Pactware V4.1 SP4
FC475 V3.9 or higher
06/2018 First edition HART 7
FW: 1.00.08 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher
AMS Device Manager V13 or high‐
er
DTM Pactware V4.1 SP4
FC475 V3.9 or higher
2.5 Checking the consignment
1. Check the packaging and the delivered items for visible damages.
2. Report any claims for damages immediately to the shipping company.
3. Retain damaged parts for clarification.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
●Do not use damaged or incomplete devices.
See also
Return procedure (Page 188)
2.6 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
Introduction
2.6 Security information
SITRANS P320/P420 with 4 to 20 mA/HART
16 Operating Instructions, 11/2019, A5E44852162-AC

In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected
to an enterprise network or the internet if and to the extent such a connection is necessary and
only when appropriate security measures (e.g. firewalls and/or network segmentation) are in
place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
https://www.siemens.com/industrialsecurity.
2.7 Transportation and storage
To guarantee sufficient protection during transport and storage, observe the following:
● Keep the original packaging for subsequent transportation.
● Devices/replacement parts should be returned in their original packaging.
● If the original packaging is no longer available, ensure that all shipments are properly
packaged to provide sufficient protection during transport. Siemens cannot assume liability
for any costs associated with transportation damages.
NOTICE
Insufficient protection during storage
The packaging only provides limited protection against moisture and infiltration.
●Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in Technical data
(Page 199).
2.8 Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing agreement,
commitment or legal relationship. The sales contract contains all obligations on the part of
Siemens as well as the complete and solely applicable warranty conditions. Any statements
regarding device versions described in the manual do not create new warranties or modify the
existing warranty.
Introduction
2.8 Notes on warranty
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 17

The content reflects the technical status at the time of publishing. Siemens reserves the right
to make technical changes in the course of further development.
Introduction
2.8 Notes on warranty
SITRANS P320/P420 with 4 to 20 mA/HART
18 Operating Instructions, 11/2019, A5E44852162-AC

Safety information 3
3.1 Precondition for use
This device left the factory in good working condition. In order to maintain this status and to
ensure safe operation of the device, observe these instructions and all the specifications
relevant to safety.
Observe the information and symbols on the device. Do not remove any information or symbols
from the device. Always keep the information and symbols in a completely legible state.
3.1.1 Warning symbols on the device
Symbol Explanation
Consult operating instructions
3.1.2 Laws and directives
Observe the safety rules, provisions and laws applicable in your country during connection,
assembly and operation. These include, for example:
●National Electrical Code (NEC - NFPA 70) (USA)
●Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
● IEC 60079-14 (international)
● EN 60079-14 (EU)
SITRANS P320/P420 with 4 to 20 mA/HART
Operating Instructions, 11/2019, A5E44852162-AC 19

3.1.3 Conformity with European directives
The CE mark on the device is a sign of conformity with the following European directives:
Electromagnetic compatibility
EMC
2014/30/EU
Directive of the European Parliament and of the Council on the harmonization
of the laws of the Member States relating to electromagnetic compatibility
Atmosphère explosible ATEX
2014/34/EU
Directive of the European Parliament and the Council on the harmonization of
the laws of the Member States concerning equipment and protective systems
intended for use in potentially explosive atmospheres
Pressure Equipment Directive
PED
2014/68/EU
Directive of the European Parliament and of the Council on the harmonization
of the laws of the Member States relating to the making available on the mar‐
ket of pressure equipment
The directives applied can be found in the EU declaration of conformity for the associated
device.
3.1.4 Classification according to the pressure equipment directive
●For gases of fluid group 1 and liquids of fluid group 1; complies with requirements of article 4,
paragraph 3 (sound engineering practice)
● Only for flow rate:
For gases of Fluid Group 1 and liquids of Fluid Group 1; fulfills the basic safety requirements
as per article 3, Para 1 (appendix 1); classified as category III, module H conformity
evaluation by TÜV Nord
WARNING
Improper device modifications
Risk to personnel, system and environment can result from modifications to the device,
particularly in hazardous areas.
● Only carry out modifications that are described in the instructions for the device. Failure to
observe this requirement cancels the manufacturer's warranty and the product approvals.
Safety information
3.1 Precondition for use
SITRANS P320/P420 with 4 to 20 mA/HART
20 Operating Instructions, 11/2019, A5E44852162-AC