Siemens SITRANS P320 Administrator guide

SITRANS P
Pressure transmitter
SITRANS P320/P420
Compact Operating Instructions
7MF03.0 (SITRANS P320 with 4 ... 20 mA/HART)
7MF03.1 (SITRANS P320 with PROFIBUS PA)
7MF03.2 (SITRANS P320 with FOUNDATION Fieldbus)
7MF04.0 (SITRANS P420 with 4 ... 20 mA/HART)
7MF04.1 (SITRANS P420 with PROFIBUS PA)
7MF04.2 (SITRANS P420 with FOUNDATION Fieldbus)
09/2021
A5E38874562-AD
Getting started 1
Introduction 2
Safety notes 3
Installing/mounting 4
Connecting 5
Commissioning 6
Service and maintenance 7
Technical data 8
Product documentation and
support A
Sealing plug / thread
adapter B

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices
referring only to property damage have no safety alert symbol. These notices shown below are graded according to
the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
Document order number: A5E38874562
Ⓟ 09/2021 Subject to change
Copyright © Siemens AG 2021.
All rights reserved

Table of contents
1 Getting started ...................................................................................................................................... 7
2 Introduction ........................................................................................................................................... 9
2.1 Purpose of this documentation ............................................................................................ 9
2.2 Scope of validity of this document........................................................................................ 9
2.3 Intended use........................................................................................................................ 9
2.4 Document history .............................................................................................................. 10
2.5 Product compatibility......................................................................................................... 11
2.6 Nameplate layout............................................................................................................... 11
2.7 Checking the consignment................................................................................................. 14
2.8 Security information .......................................................................................................... 14
2.9 Transportation and storage ................................................................................................ 15
2.10 Notes on warranty ............................................................................................................. 15
3 Safety notes ......................................................................................................................................... 17
3.1 Precondition for use........................................................................................................... 17
3.1.1 Warning symbols on the device.......................................................................................... 17
3.1.2 Laws and directives............................................................................................................ 17
3.1.3 Conformity with European directives.................................................................................. 18
3.1.4 Classi󹪝cation according to the pressure equipment directive ............................................... 18
3.2 Requirements for special applications................................................................................. 19
3.3 Use in hazardous areas....................................................................................................... 19
4 Installing/mounting ............................................................................................................................. 23
4.1 Basic safety instructions ..................................................................................................... 23
4.1.1 Installation location requirements ...................................................................................... 26
4.1.1.1 Devices with marine approval............................................................................................. 26
4.1.2 Proper mounting................................................................................................................ 27
4.2 Installation (except level) ................................................................................................... 27
4.3 Securing the device with mounting bracket ........................................................................ 29
4.4 Installation (level).............................................................................................................. 31
4.4.1 Mounting on the container ................................................................................................ 32
4.5 Removing .......................................................................................................................... 35
5 Connecting .......................................................................................................................................... 37
5.1 Basic safety instructions ..................................................................................................... 37
5.2 Connecting the device ....................................................................................................... 40
5.2.1 Opening the device............................................................................................................ 40
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 3

5.2.2 Connecting the device ....................................................................................................... 41
5.2.3 Closing the device.............................................................................................................. 42
5.3 Switching on the supply voltage......................................................................................... 43
6 Commissioning .................................................................................................................................... 45
6.1 Basic safety instructions ..................................................................................................... 45
6.2 Commissioning the device ................................................................................................. 46
6.3 Application examples......................................................................................................... 47
6.3.1 Gauge pressure, absolute pressure from di󹪜erential pressure series, and absolute
pressure from gauge pressure series................................................................................... 47
6.3.1.1 Commissioning in gaseous environments........................................................................... 47
6.3.1.2 Commissioning with steam or liquid................................................................................... 49
6.3.2 Di󹪜erential pressure and 󹪞ow rate...................................................................................... 50
6.3.2.1 Commissioning in gaseous environments........................................................................... 50
6.3.2.2 Commissioning for liquids .................................................................................................. 52
6.3.2.3 Commissioning with vapor................................................................................................. 54
7 Service and maintenance .................................................................................................................... 57
7.1 Basic safety instructions ..................................................................................................... 57
7.2 Cleaning............................................................................................................................ 58
7.2.1 Servicing the remote seal measuring system ...................................................................... 58
7.3 Maintenance and repair work............................................................................................. 58
7.3.1 De󹪝ning the maintenance interval...................................................................................... 59
7.3.2 Checking the seals ............................................................................................................. 60
7.4 Return procedure............................................................................................................... 60
7.5 Disposal............................................................................................................................. 61
8 Technical data...................................................................................................................................... 63
8.1 Input ................................................................................................................................. 63
8.1.1 Gauge pressure.................................................................................................................. 63
8.1.2 Gauge pressure with front-󹪞ush diaphragm........................................................................ 64
8.1.3 Gauge pressure from the di󹪜erential pressure series ........................................................... 65
8.1.4 Absolute pressure from the gauge pressure series............................................................... 66
8.1.5 Absolute pressure with front-󹪞ush diaphragm .................................................................... 67
8.1.6 Absolute pressure from the di󹪜erential pressure series........................................................ 68
8.1.7 Di󹪜erential pressure and 󹪞ow............................................................................................. 69
8.1.8 Level.................................................................................................................................. 71
8.2 Operating conditions ......................................................................................................... 72
8.3 Vibration resistance ........................................................................................................... 77
8.4 Construction...................................................................................................................... 78
8.5 Torques ............................................................................................................................. 82
8.6 Display, keys and auxiliary power ....................................................................................... 83
8.7 Certi󹪝cates and approvals................................................................................................... 83
A Product documentation and support .................................................................................................. 91
A.1 Product documentation ..................................................................................................... 91
Table of contents
SITRANS P320/P420
4Compact Operating Instructions, 09/2021, A5E38874562-AD

A.2 Technical support............................................................................................................... 92
B Sealing plug / thread adapter .............................................................................................................. 93
B.1 Intended use of accessory part ........................................................................................... 93
B.2 Safety instructions for accessory part ................................................................................. 93
B.3 Technical speci󹪝cations of accessory part ........................................................................... 94
B.4 Dimensional drawings for accessory part............................................................................ 95
Index .................................................................................................................................................... 97
Table of contents
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 5

Table of contents
SITRANS P320/P420
6Compact Operating Instructions, 09/2021, A5E38874562-AD

Getting started 1
Before you commission the device, observe the following safety notes:
• General safety notes (Page 17)
• Basic safety notes: Installing/mounting (Page 23)
• Basic safety notes: Connecting (Page 37)
• Basic safety notes: Commissioning (Page 45)
Read the entire device manual to achieve the optimum performance of the device.
Procedure
1. Install the device.
Installation (level) (Page 31)
Installation (except level) (Page 27)
2. Connect the device.
Connecting the device (Page 41)
3. Switch on the supply voltage.
Switching on the supply voltage (Page 43)
4. If you want to change the factory settings, con󹪝gure the device using the local or the remote
operation.
– Read the operating instructions for information on this.
5. Lock the device.
– Read the operating instructions for information on this.
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 7

Getting started
SITRANS P320/P420
8Compact Operating Instructions, 09/2021, A5E38874562-AD

Introduction 2
2.1 Purpose of this documentation
These instructions are a brief summary of important features, functions and safety information,
and contain all information required for safe use of the device. Read the instructions carefully
prior to installation and commissioning. In order to use the device correctly, 󹪝rst review its
principle of operation.
The instructions are aimed at persons who install and commission the device.
To realize optimum performance from the device, read the complete operating instructions.
2.2 Scope of validity of this document
Variant SITRANS P320 SITRANS P420
Gauge pressure 7MF030. 7MF040.
Gauge pressure from the di󹪜er‐
ential pressure series
7MF031. 7MF041.
Absolute pressure from the
gauge pressure series
7MF032. 7MF042.
Absolute pressure from the di󹪜er‐
ential pressure series
7MF033. 7MF043.
Di󹪜erential pressure and 󹪞ow
rate, MAWP 160 bar (2320 psi)
7MF034. 7MF044.
Di󹪜erential pressure and 󹪞ow
rate, MAWP 420 bar (6092 psi)
7MF035. 7MF045.
Level 7MF036. 7MF046.
Article number of the variants
2.3 Intended use
Depending on the variant, the pressure transmitter measures corrosive, non-corrosive and
hazardous gases, vapors and liquids.
You can use the pressure transmitter for the following measuring tasks:
• Gauge pressure
• Absolute pressure
•Di󹪜erential pressure
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 9

With the appropriate con󹪝guration and the necessary add-on parts (e.g. limiters and remote
seals), you can also use the pressure transmitter for the following measuring tasks:
• Level
• Volume 󹪞ow
• Mass 󹪞ow
• Volume
• Customized characteristic curve
The output signal for all measuring tasks is a direct current of 4 to 20 mA or a process-based,
digital signal (e.g. with PROFIBUS PA).
You can install the "intrinsically-safe" or "󹪞ameproof enclosure" version of the pressure
transmitter in hazardous areas. The devices have a test certi󹪝cation and comply with the
corresponding directives.
Pressure transmitters with remote seals of various shapes can be provided for special
applications. For example, measuring high-viscosity substances is a special application.
Operate the device in accordance with the speci󹪝cations in section Technical data (Page 63).
2.4 Document history
Edition Note
09/2021 New variant of the device with FOUNDATION Fieldbus.
01/2021 • Technical speci󹪝cations updated (e.g. introduction of the 160 bar measuring cell
and the internal overvoltage protection up to 6 kV)
• New variant of the device with PROFIBUS PA.
09/2018 • Section Sealing plug / thread adapter (Page 93) added.
• Technical speci󹪝cations updated
06/2018 First edition
Introduction
2.4 Document history
SITRANS P320/P420
10 Compact Operating Instructions, 09/2021, A5E38874562-AD

2.5 Product compatibility
The following table describes the compatibility between the edition of this manual, the device
revision, the engineering system and the associated EDD.
Edition Comments Device revision Compatible version of device integration package
09/2021 New type of
communication
HART 7
FW: 1.01.00 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher EDD: 1.00.00 or higher
AMS Device Manager V13 or
higher
DTM Pactware V4.2 or higher
FC475 V3.9 or higher
PROFIBUS PA
FW: 1.00.05 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher EDD: 1.00.00 or higher
DTM Pactware V4.2 or higher
FOUNDATION Fieldbus
FW: 1.00.08 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.1 or higher EDD: 1.00.00 or higher
DTM Pactware V4.3 or higher
AMS Trex Device Communica‐
tor
01/2021 Manual revised HART 7
FW: 1.01.00 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher EDD: 1.01.00 or higher
AMS Device Manager V13 or
higher
DTM Pactware V4.2 or higher
FC475 V3.9 or higher
PROFIBUS PA
FW: 1.00.05 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher EDD: 1.00.00 or higher
DTM Pactware V4.2 or higher
09/2018 Manual revised HART 7
FW: 1.00.08 or higher
HW: 1.00.00 or higher
SIMATIC PDM V9.0 or higher EDD: 1.00.00 or higher
AMS Device Manager V13 or
higher
DTM Pactware V4.1 SP4 or
higher
FC475 V3.9 or higher
06/2018 First edition
2.6 Nameplate layout
Nameplate with general information
The nameplate with the article number and other important information, such as design details
and technical data, is located on the cover over the buttons.
Introduction
2.6 Nameplate layout
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 11

Example



①Article number (MLFB number) ⑦Permitted ambient temperature for the
hazardous area of the corresponding tem‐
perature class
②Firmware and hardware identity ⑧Maximum permissible operating pressure /
maximum permissible test pressure
③QR code to the mobile website with device-spe‐
ci󹪝c information
⑨Minimum/maximum measuring span
④Conformity with country-speci󹪝c directives ⑩Material: Connection, diaphragm, O-ring,
oil
⑤Note operating instructions, certi󹪝cates and ap‐
provals
⑪Serial number
⑥Protection class ⑫Order supplement (order code)
Nameplate with approval information
The nameplate with approval information is located on the front of the enclosure.
Introduction
2.6 Nameplate layout
SITRANS P320/P420
12 Compact Operating Instructions, 09/2021, A5E38874562-AD

Examples
DEF,,*([LD,,&77*D*EHG
1a Characteristics of the hazardous area
1b Type of protection
1c Group (gas, dust)
1d Maximum surface temperature (temperature class)
1e Device protection level
Figure 2-1 Example ATEX
Figure 2-2 Example FM
Nameplate with information on the remote seals
The nameplate with information on the remote seals is located on the back of the enclosure.
Example
DE-76181
Karlsruhe
Siemens AG
Assembled in Canada
Components of France
DIAPRHAGM SEALS SANDWICH TYPE
(1P) 7MF0800-1A A11-01 A0-Z
C11+C12+E80
S N1J6129120109


OPER. TEMP: -40-85°C
VACCUM SERVICE: NO | OXYGEN≤60°;≤50bar
NOMI SIZE/PRES: 4"EXTENSION 2"CLASS 600
FILLING LIQUID: FOOD GRADE OIL (FDA GRADE)
WETTED MAT: DIAPH+FLAN DUPLEX, 1.4462
①Diaphragm remote seals of sandwich type ⑦Nominal diameter/nominal pressure: 4", 50 mm tube
length, CLASS 600
②Article number (MLFB number) ⑧Filling liquid: Food grade oil (FDA-compliant)
③Order supplement (order code) ⑨Wetted materials: Diaphragm duplex, 1.4462
④Serial number ⑩QR code for mobile website with device-speci󹪝c informa‐
tion
⑤Operating temperature ⑪Assembly and manufacturing location
⑥Vacuum service: no, oxygen ≤ 60 °C; ≤ 50 bar
Introduction
2.6 Nameplate layout
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 13

2.7 Checking the consignment
1. Check the packaging and the delivered items for visible damages.
2. Report any claims for damages immediately to the shipping company.
3. Retain damaged parts for clari󹪝cation.
4. Check the scope of delivery by comparing your order to the shipping documents for
correctness and completeness.
WARNING
Using a damaged or incomplete device
Risk of explosion in hazardous areas.
• Do not use damaged or incomplete devices.
2.8 Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is necessary
to implement – and continuously maintain – a holistic, state-of-the-art industrial security
concept. Siemens’ products and solutions form one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. These systems, machines and components should only be connected
to the enterprise network or the Internet if and only to the extent necessary and with appropriate
security measures (󹪝rewalls and/or network segmentation) in place.
You can 󹪝nd more information on protective measures in the area of industrial security by
visiting:
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends performing product updates as soon as they are available and
using only the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed
under
https://www.siemens.com/industrialsecurity.
Download any type of software 󹪝les (available updates such as EDD) only from secure sources
(e.g. SIOS Portal or SIEMENS page of product family).
Introduction
2.8 Security information
SITRANS P320/P420
14 Compact Operating Instructions, 09/2021, A5E38874562-AD

2.9 Transportation and storage
To guarantee su󹪟cient protection during transport and storage, observe the following:
• Keep the original packaging for subsequent transportation.
• Devices/replacement parts should be returned in their original packaging.
• If the original packaging is no longer available, ensure that all shipments are properly
packaged to provide su󹪟cient protection during transport. Siemens cannot assume liability
for any costs associated with transportation damages.
NOTICE
Insu󹪟cient protection during storage
The packaging only provides limited protection against moisture and in󹪝ltration.
• Provide additional packaging as necessary.
Special conditions for storage and transportation of the device are listed in Technical data
(Page 63).
2.10 Notes on warranty
The contents of this manual shall not become part of or modify any prior or existing agreement,
commitment or legal relationship. The sales contract contains all obligations on the part of
Siemens as well as the complete and solely applicable warranty conditions. Any statements
regarding device versions described in the manual do not create new warranties or modify the
existing warranty.
The content re󹪞ects the technical status at the time of publishing. Siemens reserves the right to
make technical changes in the course of further development.
Introduction
2.10 Notes on warranty
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 15

Introduction
2.10 Notes on warranty
SITRANS P320/P420
16 Compact Operating Instructions, 09/2021, A5E38874562-AD

Safety notes 3
3.1 Precondition for use
This device left the factory in good working condition. In order to maintain this status and to
ensure safe operation of the device, observe these instructions and all the speci󹪝cations relevant
to safety.
Observe the information and symbols on the device. Do not remove any information or symbols
from the device. Always keep the information and symbols in a completely legible state.
3.1.1 Warning symbols on the device
Symbol Explanation
Consult operating instructions
3.1.2 Laws and directives
Observe the safety rules, provisions and laws applicable in your country during connection,
assembly and operation. These include, for example:
• National Electrical Code (NEC - NFPA 70) (USA)
• Canadian Electrical Code (CEC) (Canada)
Further provisions for hazardous area applications are for example:
• IEC 60079-14 (international)
• EN 60079-14 (EU)
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 17

3.1.3 Conformity with European directives
The CE mark on the device is a sign of conformity with the following European directives:
Electromagnetic compatibility
EMC
2014/30/EU
Directive of the European Parliament and of the Council on the harmonization
of the laws of the Member States relating to electromagnetic compatibility
Atmosphère explosible ATEX
2014/34/EU
Directive of the European Parliament and the Council on the harmonization of
the laws of the Member States concerning equipment and protective systems
intended for use in potentially explosive atmospheres
Pressure Equipment Directive PED
2014/68/EU
Directive of the European Parliament and of the Council on the harmonization
of the laws of the Member States relating to the making available on the market
of pressure equipment
The directives applied can be found in the EU declaration of conformity for the associated device.
3.1.4 Classi󹪝cation according to the pressure equipment directive
• For gases of 󹪞uid group 1 and liquids of 󹪞uid group 1; complies with requirements of article 4,
paragraph 3 (sound engineering practice)
• Only for devices with MAWP 420 bar (6092 psi):
For gases of Fluid Group 1 and liquids of Fluid Group 1; ful󹪝lls the basic safety requirements
as per article 3, Para 1 (appendix 1); classi󹪝ed as category III, module H conformity evaluation
by TÜV Nord
WARNING
Improper device modi󹪝cations
Risk to personnel, system and environment can result from modi󹪝cations to the device,
particularly in hazardous areas.
• Only carry out modi󹪝cations that are described in the instructions for the device. Failure to
observe this requirement cancels the manufacturer's warranty and the product approvals.
Safety notes
3.1 Precondition for use
SITRANS P320/P420
18 Compact Operating Instructions, 09/2021, A5E38874562-AD

3.2 Requirements for special applications
Due to the large number of possible applications, each detail of the described device versions for
each possible scenario during commissioning, operation, maintenance or operation in systems
cannot be considered in the instructions. If you need additional information not covered by
these instructions, contact your local Siemens o󹪟ce or company representative.
Note
Operation under special ambient conditions
We highly recommend that you contact your Siemens representative or our application
department before you operate the device under special ambient conditions as can be
encountered in nuclear power plants or when the device is used for research and development
purposes.
DANGER
Using equipment with approval-related restrictions
Risk of explosion, damage to property due to operating conditions not in conformity with the
approval (e.g. temperature and pressure limits exceeded)
• Take note of the approval restrictions before using the device. You can 󹪝nd the information
on this in the current certi󹪝cates.
See also
Product documentation (Page 91)
3.3 Use in hazardous areas
Quali󹪝ed personnel for hazardous area applications
Persons who install, connect, commission, operate, and service the device in a hazardous area
must have the following speci󹪝c quali󹪝cations:
• They are authorized, trained or instructed in operating and maintaining devices and systems
according to the safety regulations for electrical circuits, high pressures, aggressive, and
hazardous media.
• They are authorized, trained, or instructed in carrying out work on electrical circuits for
hazardous systems.
• They are trained or instructed in maintenance and use of appropriate safety equipment
according to the pertinent safety regulations.
Safety notes
3.3 Use in hazardous areas
SITRANS P320/P420
Compact Operating Instructions, 09/2021, A5E38874562-AD 19

WARNING
Use in hazardous area
Risk of explosion.
• Only use equipment that is approved for use in the intended hazardous area and labeled
accordingly.
• Do not use devices that have been operated outside the conditions speci󹪝ed for hazardous
areas. If you have used the device outside the conditions for hazardous areas, make all Ex
markings unrecognizable on the nameplate.
See also
Technical data (Page 63)
WARNING
Loss of safety of device with type of protection "Intrinsic safety Ex i"
If the device or its components have already been operated in non-intrinsically safe circuits or
the electrical speci󹪝cations have not been observed, the safety of the device is no longer
ensured for use in hazardous areas. There is a risk of explosion.
• Connect the device with type of protection "Intrinsic safety" solely to an intrinsically safe
circuit.
• Observe the speci󹪝cations for the electrical data on the certi󹪝cate and/or in Technical data
(Page 63).
WARNING
Use of incorrect device parts in potentially explosive environments
Devices and their associated device parts are either approved for di󹪜erent types of protection
or they do not have explosion protection. There is a risk of explosion if device parts (such as
covers) are used for devices with explosion protection that are not expressly suited for this type
of protection. If you do not adhere to these guidelines, the test certi󹪝cates and the
manufacturer warranty will become null and void.
• Use only device parts that have been approved for the respective type of protection in the
potentially explosive environment. Covers that are not suited for the "explosion-proof" type
of protection are identi󹪝ed as such by a notice label attached to the inside of the cover with
"Not Ex d Not SIL".
• Do not swap device parts unless the manufacturer speci󹪝cally ensures compatibility of
these parts.
Safety notes
3.3 Use in hazardous areas
SITRANS P320/P420
20 Compact Operating Instructions, 09/2021, A5E38874562-AD