SIGMA TEK SCP 111 User manual

SCP 111
S-DIAS Safety CPU Module
Instruction Manual
Date of creation: 20.05.2015
Version date: 05.12.2023
Article number: 20-890-111-E

Publisher: SIGMATEK GmbH & Co KG
A-5112 Lamprechtshausen
Tel.: [phone]
Fax: [phone]
Email: [email protected]
WWW.SIGMATEK-AUTOMATION.COM
Copyright © 2015
SIGMATEK GmbH & Co KG
Translation of the Original Instruction
All rights reserved. No part of this work may be reproduced, edited using an electronic system, duplicated or
distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.
We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsible
for technical or printing errors in the handbook and assumes no responsibility for damages that occur through use
of this handbook.

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 1
S-DIAS Safety CPU Module SCP 111
The S-DIAS Safety CPU module supports up to 16 Safe IO modules. In
addition, the SCP 111 can operate handheld devices with Emergency Stop
and/or confirmation buttons.
The Safety CPU component has the safety integrity level SIL3 (EN IEC
62061) or Performancelevel e (PL e) (EN ISO 13849).
The safety-related SCP 111 is ideal for use in systems with optional
modules and interface variables according to Safety System Handbook,
see homepage
1
.
With the SCP 111, Safe process data is transmitted with its own safety
protocol (FSoE). Therefore, the SCP 111 cannot be used with a CSCP
011/012, SCP 010/011 in a Safety project.
The SCP 111 alone is already a minimal system of a safety control.
In addition, the Safety SCP 111 regulates the synchronized communication
with the remote safety modules through safe bus telegrams. Included
among their jobs are:
•Processing the safe application and
•The distribution of configuration data to remote safety modules
SCP 111-X: main board and S-DIAS connectors coated in Purocoat (Certonal)
1
Using the search function with the keyword “Safety System Handbook”

SCP 111 S-DIAS SAFETY CPU MODULE
Page 2 05.12.2023
Contents
1Introduction............................................................................. 6
1.1 Target Group/Purpose of this Operating Manual......................6
1.2 Important Reference Documentation .........................................6
1.3 Contents of Delivery.....................................................................6
2Basic Safety Guidelines......................................................... 7
2.1 Symbols Used...............................................................................7
2.2 Disclaimer......................................................................................9
2.3 General Safety Directives ..........................................................10
2.4 Designated Use...........................................................................12
2.5 Software/Training .......................................................................13
3IT Security ..............................................................................14
4Standards and Directives......................................................15
4.1 Residual Risks ............................................................................15
4.2 Safety of the Machine or Equipment ........................................15
4.3 Directives.....................................................................................15
4.3.1 Functional Safety Standards..............................................................16
4.3.2 EU Conformity Declaration................................................................16
4.4 Safety-Relevant Parameters......................................................17
4.4.1 Mounting Position Horizontal 0-55 °C Ambient Temperature ............17
4.4.2 Mounting Position Horizontal 55-60 °C Ambient Temperature ..........17
4.5 Compatibility...............................................................................18

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 3
5Type Plate ..............................................................................19
6Technical Data.......................................................................20
6.1 Performance Data.......................................................................20
6.2 Electrical Requirements.............................................................21
6.2.1 Module Supply (Input)....................................................................... 21
6.2.2 S-DIAS Bus/Safety Supply (Output).................................................. 22
6.3 Miscellaneous .............................................................................24
6.4 Environmental Conditions.........................................................24
7Mechanical Dimensions........................................................25
8Connector Layout..................................................................26
8.1 Status LEDs.................................................................................27
8.2 Applicable Connectors...............................................................28
8.3 Label Field...................................................................................29
9Validation Button...................................................................30
9.1 Explanation of the Individual Sequences.................................30
9.1.1 Start Sequence................................................................................. 30
9.1.2 Command Selection Sequence......................................................... 31
9.1.3 End Sequence .................................................................................. 31
9.1.4 Error Sequence................................................................................. 31
9.2 Overview of Commands.............................................................32
9.3 Overview of Module Status and Commands............................32
9.4 Handling the microSD Card (mSD) ...........................................34

SCP 111 S-DIAS SAFETY CPU MODULE
Page 4 05.12.2023
9.5 Configuring a Safety CPU with the mSD Card.........................35
10 Error Response......................................................................36
10.1 Restart Errors..............................................................................36
10.2 Configuration Distribution Error...............................................37
10.3 Troubleshooting .........................................................................38
10.4 Troubleshooting with the SafetyDesigner ...............................38
10.5 Correcting a Wiring Error...........................................................38
11 Wiring Guidelines ..................................................................39
11.1 Shielding......................................................................................40
11.2 ESD Protection............................................................................40
12 Assembly/Installation............................................................41
12.1 Check Contents of Delivery.......................................................41
12.2 Mounting......................................................................................42
13 Supported Cycle Times.........................................................44
13.1 Cycle Times below 1 ms (in µs).................................................44
13.2 Cycle Times equal to or higher than 1 ms (in ms)...................44
14 Transport/Storage..................................................................45
15 Storage ...................................................................................45
16 Maintenance...........................................................................46
16.1 Service.........................................................................................46
16.2 Repair...........................................................................................46

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 5
17 Disposal .................................................................................46

SCP 111 S-DIAS SAFETY CPU MODULE
Page 6 05.12.2023
1 Introduction
1.1 Target Group/Purpose of this Operating Manual
This operating manual contains all information required for the operation of the product.
This operating manual is intended for:
•Project planners
•Technicians
•Commissioning engineers
•Machine operators
•Maintenance/test technicians
General knowledge of automation technology is required.
Further help and training information, as well as the appropriate accessories can be found on
our website www.sigmatek-automation.com.
Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.
1.2 Important Reference Documentation
•Safety System Handbook
This and additional documents can be downloaded from our website or obtained through
support.
1.3 Contents of Delivery
1x SCP 111

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 7
2 Basic Safety Guidelines
2.1 Symbols Used
The following symbols are used in the operator documentation for warning and danger
messages, as well as informational notes:
DANGER
Danger indicates that death or serious injury will occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Danger indique une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
WARNING
Warning indicates that death or serious injury can occur, if the specified
measures are not taken.
To avoid death or serious injuries, observe all guidelines.
Avertissement d’une situation dangereuse qui, faute de prendre les
mesures adéquates, entraînera des blessures graves, voire mortelles.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.
CAUTION
Caution indicates that moderate to slight injury can occur, if the
specified measures are not taken.
To avoid moderate to slight injuries, observe all guidelines.
Attention indique une situation dangereuse qui, faute de prendre les
mesures adéquates, peut entraîner des blessures assez graves ou
légères.
Respectez toutes les consignes pour éviter des blessures
graves, voire mortelles.

SCP 111 S-DIAS SAFETY CPU MODULE
Page 8 05.12.2023
CAUTION
Danger for ESD-sensitive components.
Les signes de danger pour les composants sensibles aux décharges
électrostatiques.
INFORMATION
Information
Provides important information on the product, handling or
relevant sections of the documentation, which require
attention.

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 9
2.2 Disclaimer
INFORMATION
The contents of this operating manual were prepared with the greatest
care. However, deviations cannot be ruled out. This operating manual
is regularly checked and required corrections are included in the
subsequent versions. The machine manufacturer is responsible for the
proper assembly, as well as device configuration. The machine
operator is responsible for safe handling, as well as proper operation.
The current operating manual can be found on our website. If
necessary, contact our support.
Subject to technical changes, which improve the performance of the
devices. The following operating manual is purely a product
description. It does not guarantee properties under the warranty.
Please thoroughly read the corresponding documents and this
operating manual before handling a product.
SIGMATEK GmbH & Co KG is not liable for damages caused
through, non-compliance with these instructions or applicable
regulations.

SCP 111 S-DIAS SAFETY CPU MODULE
Page 10 05.12.2023
2.3 General Safety Directives
The Safety Directives in the other sections of this operating manual must be observed. These
instructions are visually emphasized by symbols.
INFORMATION
According to EU Directives, the operating manual is a component of a
product.
This operating manual must therefore be accessible in the vicinity of
the machine since it contains important instructions.
This operating manual should be included in the sale, rental or transfer
of the product, or its online availability indicated.
Regarding the requirements for Safety and health connected to the use
of machines, the manufacturer must perform a risk assessment in
accordance with machine directives 2006/42/EG before introducing a
machine to the market.
Operate the unit with devices and accessories approved by
SIGMATEK only.

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 11
CAUTION
Handle the device with care and do not drop or let fall.
Prevent foreign bodies and fluids from entering the device.
The device must not be opened!
Manipulez l’appareil avec précaution et ne le laissez pas tomber.
Empêchez les corps étrangers et les liquides de pénétrer dans
l’appareil.
L’appareil ne doit pas être ouvert!
If the device does not function as intended or has damage that could
pose a danger, it must be replaced!
En cas de fonctionnement non conforme ou de dommages pouvant
entraîner des risques, l'appareil doit être remplacé!
The module complies with EN 61131-2.
In combination with a facility, the system integrator must comply with
EN 60204-1 standards.
For your own safety and that of others, compliance with the
environmental conditions is essential.
Le module est conforme à la norme EN 61131-2.
En combinaison avec une équipement, l’intégrateur de système doit
respecter la norme EN 60204-1.
Pour votre propre sécurité et celle des autres, le respect des conditions
environnementales est essential.

SCP 111 S-DIAS SAFETY CPU MODULE
Page 12 05.12.2023
2.4 Designated Use
The Safety functions implemented in the product are designed for use with safety applications
in a SIGMATEK control and meet the required conditions for safe operation according to SIL
3, HFT 1 n compliance with EN 62061 and according to PL e, Kat. 4 in compliance with EN
ISO 13849-1.
CAUTION
The instructions contained in this operating manual must be followed.
For error-free operation, proper transport and storage are essential.
Installation, mounting, programming, initial start-up, operation,
maintenance and decommissioning can only be performed by qualified
personnel.
Qualified personnel in this context are people, who have completed
training or have trained under supervision of qualified personnel and
have been authorized to operate and maintain safety-related
equipment, systems and facilities in compliance with the strict
directives and standards of safety technology (Functional Safety).
Les instructions contenues dans ce manuel technique doivent être
suivies.
Pour un fonctionnement sans erreur, le transport et le stockage
appropriés sont essentiels.
L’installation, le montage, la programmation, la mise en service initiale,
l’exploitation, la maintenance et la mise hors service ne peuvent être
effectués que par une personne qualifiée.
Dans ce contexte, on entend par personnel qualifié les personnes qui
ont suivi une formation ou qui ont été formées sous la supervision d’un
personnel qualifié et qui ont été autorisées à utiliser et à entretenir
l’équipement, les systèmes et les installations de sécurité
conformément aux directives et aux normes strictes de la technique de
sécurité (Sécurité fonctionnelle).
For your own safety and that of others, the product should be used for
their designated purpose only.
Correct EMC installation is also included under designated use.
Pour votre propre sécurité et celle des autres, le produit ne doivent être
utilisés qu’à des fins prévues.

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 13
Une installation CEM correcte est également incluse dans l’utilisation
prévue.
Non-designated use consists of:
•any changes made to the module or the use of damaged
modules.
•use of the module inconsistent with the technical margins
described in this operating manual or the specifications
defined in the technical data.
L'utilisation non désignée consiste en:
•toute modification apportée au module ou l'utilisation des
modules endommagés.
•utilisation du module non conforme aux marges techniques
décrites dans ce manuel ou aux spécifications définies dans
les données techniques.
Before delivering the module, the machine manufacturer must ensure
that it is in “delivery condition”. See chapter Transport/Storage for more
information.
Avant de livrer le module, le constructeur de la machine doit s'assurer
qu'il est en "état de livraison". Voir le chapitre Transport/Storage pour
plus d’informations.
2.5 Software/Training
The application is created with the software LASAL CLASS 2 and LASAL SCREEN Editor,
the Safety application is created using the SAFETYDesigner. Basic information on Safety
(Functional Safety) can be found in the Safety System Handbook.
Training for the LASAL development environment, with which the product can be configured,
is provided. Information on our training schedule can be found on our website.

SCP 111 S-DIAS SAFETY CPU MODULE
Page 14 05.12.2023
3 IT Security
S-DIAS safety modules were developed for integration into a network protected against
unauthorized access. For example, the following dangers can affect the network:
•Unauthorized access
•Data manipulation
•and many other IT security violations
It is the responsibility of the operator to protect the safe connection between S-DIAS modules
against unauthorized access. The following measures, for example, are suitable for this:
•Firewalls
•Password-protected user accounts
•Data encryption
•and much more

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 15
4 Standards and Directives
4.1 Residual Risks
CAUTION
The following residual risks for the product must be included in the
system integrator's risk assessment:
•Release of non-environmentally safe substances, emissions
and unusual temperatures
•Possible effects of information technology devices
Les risques résiduels suivants pour le produit doivent être inclus dans
l'évaluation des risques de l'intégrateur de système:
•Libération de substances non respectueuses de
l'environnement, émissions et températures inhabituelles
•Effets possibles des dispositifs de technologie de l'information
4.2 Safety of the Machine or Equipment
INFORMATION
Observe all on-site rules and regulations for accident prevention and
occupational safety.
4.3 Directives
The product was constructed in compliance with the following European Union directives and
tested for conformity.

SCP 111 S-DIAS SAFETY CPU MODULE
Page 16 05.12.2023
4.3.1 Functional Safety Standards
EN IEC 62061 - Safety of machinery - Functional safety of safety-related control systems
EN ISO 13849-1 - Safety of machinery —Safety-related parts of control systems —Part 1:
General principles for design
EN ISO 13849-2 - Safety of machinery —Safety-related parts of control systems —Part 2:
Validation
4.3.2 EU Conformity Declaration
EU Declaration of Conformity
The product SCP 111 conforms to the following European directives:
•2006/42/EG Machine Directive
•2014/30/EU Electromagnetic Compatibility (EMC Directive)
•2011/65/EU “Restricted use of certain hazardous substances in
electrical and electronic equipment” (RoHS Directive)
The EU Conformity Declarations are provided on the SIGMATEK website.
See Products/Downloads or use the search function and the keyword “EU
Declaration of Conformity”.

S-DIAS SAFETY CPU MODULE SCP 111
05.12.2023 Page 17
4.4 Safety-Relevant Parameters
4.4.1 Mounting Position Horizontal 0-55 °C Ambient Temperature
CPU Module
Safety Parameters
Safety Levels
SCP 011
PFHD= 1,4E-10 (1/h)
MTTFD= 2689 years
DC = 99 %
SFF = 99 %
SIL 3
according to EN IEC 62061
PL e / Cat. 4
according to EN ISO 13849
Structure: Two-channel redundant (diverse)
4.4.2 Mounting Position Horizontal 55-60 °C Ambient Temperature
CPU Module
Safety Parameters
Safety Levels
SCP 011
PFHD= 1,7E-10 (1/h)
MTTFD= 2243 years
DC = 99 %
SFF = 99 %
SIL 3
according to EN IEC 62061
PL e / Cat. 4
according to EN ISO 13849
Structure: Two-channel redundant (diverse)

SCP 111 S-DIAS SAFETY CPU MODULE
Page 18 05.12.2023
4.5 Compatibility
The safety-related component, SCP 111, is supported with Firmware version 423 or Build
No, 1348 and higher of the Safety Designer.
INFORMATION
Compatibility
In regard to compatibility with the S-DIAS Safety component, section
"Compatibility with S-DIAS Safety Components" in the system
handbook is referenced.