SignaMax 065-7405TB User manual

HardenedEthernetSwitch
1
Signamax™Connectivity SystemsSignamax™Connectivity Systems
Hardened Ethernet SwitchHardened Ethernet Switch
Model -065-7405TBModel -065-7405TB
065-7408ATB065-7408ATB
065-74091FXSTTB065-74091FXSTTB
065-74091FXSCTB065-74091FXSCTB
U SER ’ S G UIDE U SER ’ S G UIDE

HardenedEthernetSwitch
Quick Start Guide
This quick start guide describes how to install and use the
Signamax hardened Ethernet Switch. This is the switch of
choice for harsh environments constrained by space.
Physical Description
The Terminal Block and Power inputs
2

HardenedEthernetSwitch
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this Switch.
Redundant power supplies function is supported. You only
need to have one power input connected to run the Switch.
The 10/100BaseT/TX and 100BaseFX Connectors
1. The 10/100BaseT/TX Connections
The following lists the pinouts of 10/100BaseT/TX ports.
Pin Regular Ports Uplink port
1 Input Receive Data + Output Transmit Data +
2 Input Receive Data - Output Transmit Data -
3 Output Transmit Data + Input Receive Data +
4 NC NC
5 NC NC
6 Output Transmit Data - Input Receive Data -
7 NC NC
8 NC NC
2. The 100BaseFX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
3

HardenedEthernetSwitch
The Port Status LEDs
4

HardenedEthernetSwitch
5
Functional Description
yMeets NEMA TS1/TS2 Environmental requirements
such as temperature, shock, and vibration for traffic
control equipment.
yMeets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
yUL1604 Class 1, Division 2 Classified for use in
hazardous locations.
ySupport 802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, full/half-duplex; Auto MDI/MDIX.
y100BaseFX: Multi mode SC or ST type; Single mode
SC or ST type; WDM Single mode SC type.
ySupport 2048 MAC addresses. Provides 768K bits
memory buffer.
yAlarms for power and port link failure by relay output.
yOperating voltage and Max. current consumption:
0.76A @ 12VDC, 0.38A @ 24VDC, 0.19A @ 48VDC.
Power consumption: 9.12W Max.
yPower Supply: Redundant DC Terminal Block power
inputs with 100-240VAC external power supply.
y-40℃to 75℃(-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40℃to 85℃
(-40℉to 185℉).
ySupports DIN-Rail or Panel Mounting installation.

HardenedEthernetSwitch
6
LED State Indication
POWER
Steady Switch is properly connected to power and
turned on.
PWR1
PWR2
(Green) Off Switch is not connected to power and is
turned off.
FAULT
Steady
1. Power failure occurred.
2. Port failure occurred (when port fault alarm
dip switch is enabled).
FAULT
(Red)
Off
1. Power failure is not occurred.
2. Port failure is not occurred (when port fault
alarm dip switch is enabled).
3. Port fault alarm dip switch is disabled.
10/100BaseT/TX or 100BaseFX
Steady A valid network connection established.
LNK stands for LINK.
LNK/ACT
(Green) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Light solid yellow for a port transferring at
100Mbps.
100
(Yellow) Off The port is transferring at 10Mbps If this LED
is dark.
Assembly, Startup, and Dismantling
yAssembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.
yStartup: Connect the supply voltage to start up the
switch via the terminal block.
yDismantling: Pull out the lower edge and then remove
the switch from the DIN rail.

HardenedEthernetSwitch
7

HardenedEthernetSwitch
8
Preface
A member of the growing Signamax family of harsh
environment switches, this switch addresses a need for a
smaller switch. This switch provides an affordable solution
for rugged and outdoor environment, transportation
road-side cabinet, industrial floor shop, multitenant
dwellings or Fiber To The Home (FTTH) applications.
Capable of operating at temperature extremes of -40°C to
+75°C, this is the switch of choice for harsh environments
constrained by space.
Plug-and-Play Solution:
The switch is a plug-and-play Fast Ethernet Switch in
compact size. It doesn't have any complicated software to
set up.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
yFeatures on the switch
yIllustrative LED functions
yInstallation instructions
ySpecifications

HardenedEthernetSwitch
9
Table of Contents
QUICK START GUIDE................................................................2
PHYSICAL DESCRIPTION..............................................................2
The Terminal Block and Power inputs..............................2
The 10/100BaseT/TX and 100BaseFX Connectors ......3
The Port Status LEDs.........................................................4
FUNCTIONAL DESCRIPTION .........................................................5
ASSEMBLY,STARTUP,AND DISMANTLING....................................6
PREFACE......................................................................................8
TABLE OF CONTENTS..............................................................9
PRODUCT OVERVIEW.............................................................10
HARDENED ETHERNET SWITCH.................................................10
PACKAGE CONTENTS................................................................. 11
PRODUCT HIGHLIGHTS .............................................................. 11
Basic Features................................................................... 11
FRONT PANEL DISPLAY..............................................................12
PHYSICAL PORTS ....................................................................... 13
INSTALLATION..........................................................................14
SELECTING A SITE FOR THE SWITCH ..........................................14
DIN RAIL MOUNTING ...............................................................15
CONNECTING TO POWER ........................................................... 16
Redundant DC Terminal Block Power Inputs................16
Alarms for Power and Port Failure..................................... 17
CONNECTING TO YOUR NETWORK ............................................18
Cable Type & Length........................................................18
Cabling................................................................................19
SPECIFICATIONS......................................................................20
APPENDIX A – CONNECTOR PINOUTS..............................22
CONTACT INFORMATION.......................................................23

HardenedEthernetSwitch
Product Overview
Hardened Ethernet Switch
10

HardenedEthernetSwitch
11
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3This Switch
3User’s Manual
3External power adapter & Power Cord
(Optional)
Product Highlights
Basic Features
yMeets NEMA TS2 Environmental requirements such as
temperature, shock, and vibration for traffic control
equipment.
yMeets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
yUL1604 Class 1, Division 2 Classified for use in
hazardous locations.
ySupport 802.3/802.3u/802.3X.
yAuto-negotiation: 10/100Mbps, Full/half-duplex; Auto
MDI/MDIX.
ySupport 2048 MAC addresses.
yProvides 768K bits memory buffer.
yAlarms for power and port link failure by relay output.
yOperating voltage and Max. current consumption:
0.76A @ 12VDC, 0.38A @ 24VDC, 0.19A @ 48VDC.
Power consumption: 9.12W Max.
yPower Supply: Redundant DC Terminal Block power
inputs with 100-240VAC external power supply.
y-40℃to 75℃(-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40℃to 85℃
(-40℉to 185℉).

HardenedEthernetSwitch
ySupports DIN-Rail or Panel Mounting installation.
Front Panel Display
12

HardenedEthernetSwitch
13
Status LEDs
LED State Indication
POWER
Steady Switch is properly connected to power and turned on.PWR1
PWR2
(Green) Off Switch is not connected to power and is turned off.
FAULT
Steady
3. Power failure occurred.
4. Port failure occurred (when port fault alarm dip
switch is enabled).
FAULT
(Red)
Off
3. Power failure is not occurred.
4. Port failure is not occurred (when port fault alarm
dip switch is enabled).
3. Port fault alarm dip switch is disabled.
10/100BaseT/TX or 100BaseFX
Steady A valid network connection established.
LNK stands for LINK.
LNK/ACT
(Green) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Light solid yellow for a port transferring at 100Mbps.100
(Yellow) Off The port is transferring at 10Mbps If this LED is dark.
Physical Ports
This switch provides:
•Five 10/100BaseT/TX ports
•Four 10/100BaseT/TX ports + one 100BaseFX port
•Four 10/100BaseT/TX ports + two 100BaseFX ports
•Eight 10/100BaseT/TX ports
•Eight 10/100BaseT/TX ports + one 100BaseFX port
•Six 10/100BaseT/TX ports + two 100BaseFX ports
•Four 10/100BaseT/TX ports + four 100BaseFX ports
CONNECTIVITY
•RJ-45 connectors
•SC or ST connector on 100BaseFX fiber port

HardenedEthernetSwitch
14
Installation
This chapter gives step-by-step instructions about how to
install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
- The ambient temperature should be between -40 to 75
degrees Celsius.
- The relative humidity should be less than 95 percent,
non-condensing.
- Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.
- Make sure that the switch receives adequate ventilation.
Do not block the ventilation holes on each side of the
switch
- The power outlet should be within 1.8 meters of the
switch.

HardenedEthernetSwitch
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the
switch.
Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch
from the DIN rail.
15

HardenedEthernetSwitch
Connecting to Power
Redundant DC Terminal Block Power Inputs
There are two pairs of power inputs can be used to power
up this device. You only need to have one power input
connected to run the switch.
Step 1: Connect the DC power cord to the plug-able terminal block on the
switch, and then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the switch.
16

HardenedEthernetSwitch
Alarms for Power and Port Failure
Step 1: There are two pins on the terminal block are used for power failure
detection. It provides the normally closed output when the power
source is active. Use this as a dry contact application to send a
signal for power failure detection.
Special note:
The relay output is normal open position when there is no power to the
switch. Please do not connect any power source to this terminal to
prevent the shortage to your power supply.
17

HardenedEthernetSwitch
18
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below
when connecting the switch to your network. Use
appropriate cables that meet your speed and cabling
requirements.
Cable pecificationsS
Speed Connector Port Speed
Half/Full
Duplex
Cable Max.
Distance
10BaseT RJ-45 10/20 Mbps
2-pair
UTP/STP Cat.
3, 4, 5
100 m
100BaseTX RJ-45 100/200 Mbps
2-pair
UTP/STP Cat.
5
100 m
100BaseFX SC, ST 100/200 Mbps MMF (50 or
62.5μm) 2 km
100BaseFX SC, ST 100/200 Mbps SMF (9 or
10μm)
15, 40, or 75
km

HardenedEthernetSwitch
19
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port
in use.
Step 3: Consult the previous section for cabling requirements based on
connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a
desired device.
Step 5: Once the connections between two end devices are made
successfully, turn on the power and the switch is operational.

HardenedEthernetSwitch
20
Specifications
Hardened Ethernet
Switch
10/100BaseT/TX auto-negotiating ports with
RJ-45 connectors, 100BaseFX fiber ports
Applicable
Standards
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX/FX
Switching Method Store-and-Forward
Forwarding Rate
10BaseT:
100BaseTX/FX:
10 / 20Mbps half / full-duplex
100 / 200Mbps half / full-duplex
Performance 14,880pps for 10Mbps
148,810pps for 100Mbps
Cable
10BaseT:
100BaseTX:
100BaseFX:
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)
LED Indicators Per unit – Power status (Power 1, Power 2)
FAULT
Per port –10/100BaseT/TX or 100BaseFX -
LNK/ACT (Green), 100 (Yellow)
Dimensions 50mm (W) × 110mm (D) × 135mm (H)
(1.97” (W) x 4.33” (D) x 5.31” (H))
Net Weight 0.8Kg (1.76lbs.)
Power Terminal Block: 12-48VDC
Operating Voltage &
Max. Current
Consumption
0.76A @ 12VDC, 0.38A @ 24VDC,
0.19A @ 48VDC
Power Consumption 9.12W Max.
Operating
Temperature -40°C to 75℃(-40℉to 167℉)
Tested for functional operation @
-40℃to 85℃(-40℉to 185℉)
Storage Temperature -45°C to 85°C (-40℉to 185℉)
Humidity 5%-95% non-condensing
Safety Hazardous location: Class 1, Division 2 group
A, B, C & D
UL60950-1, EN60950-1, IEC60950-1
EMI FCC Part 15, Class A
EN61000-6-3:
EN55022, EN61000-3-2, EN61000-3-3
EMS