SignaMax 065-7714HSFPTB User manual

Hardened Managed Ethernet Switch
1
This Gigabit Ethernet SFP media converter is a plug-and-play device. Connect the supplied AC
to DC power adaptor to the receptacle on the rear panel of the Gigabit Ethernet media converter,
and then attach the plug into a standard AC outlet with a voltage range from 100 to 240V AC.
DIP Switch
DIP
switch
Up (Default Setting) Down
Left-hand
side
The fiber port auto detects
full and half duplex
Forces the fiber port to full
duplex mode
Right-hand
side
Disable LFS Enable LFS LFS:
Link fault signaling
function
The 1000BaseT and 1000BaseSX/LX Connectors
The 1000BaseT
Connection
The following lists the pinouts of the
1000BaseT port.
The 1000BaseSX/LX
Connection
The SFP socket accepts standard Gigabit
Ethernet Small Form-factor Pluggable (SFP)
modules of various types and spectra.
The Port Status LEDs
ription
DIP switch configuration for Link Fault Signaling
enable/disable and fiber auto/force mode.
Signamax™Connectivity Systems
Hardened Managed Ethernet Switch
Model - 065-7714HSFPTB
User’s Guide

Hardened Managed Ethernet Switch
2
Quick Start Guide
This quick start guide describes how to install and use the
Hardened Managed Ethernet Switch. This is the switch of
choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power Inputs
LED State Indication
10/100BaseTX
Steady A valid network connection established.
Link/ACT
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Communication speed is 100Mbps.
10/100
Off Communication speed is 10Mbps.
10/100/1000BaseTX, 1000BaseSX/LX
Steady A valid network connection established.
Link/ACT
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Communication speed is 1000Mbps.
1000
Off Communication speed is 10/100Mbps.
Steady A valid network connection established.
SFP Link
Off No valid network connection established.

Hardened Managed Ethernet Switch
3
Power Input Assignment
Power3 12VDC DC Jack
＋12-32VDC
Power1
－Power Ground
Power2
＋12-32VDC
Earth Ground
Terminal Block
There are two pairs of power inputs can be used to power up this switch.
Redundant power supplies function is supported.
Options A-Terminal Block power supplies, part numbers: DC-1824-30W;
DC-1824-60W; DC-1824-75W; DC-1824-120W
Options B- DC Jack power supply
※Signamax strongly recommends the use of a terminal block power
supply; however, a jack for power is also provided. Please see the
pinout chart below for use when wiring a power jack for this equipment:
Output No. Name
PIN 1 V+
PIN 2 GND
PIN 3 NC

Hardened Managed Ethernet Switch
4
Functional Description
Meets NEMA TS1/TS2 Environmental requirements such as
temperature, shock, and vibration for traffic control equipment.
Meets EN61000-6-2 EMC Generic Standard Immunity for industrial
environment.
Manageable via SNMP, Web-based, Telnet, and RS-232 console port.
Support 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation:
10/100/1000Mbps, full/half-duplex; Auto MDI/MDIX.
1000Base-SX/LX: Multi mode or Single mode SC type; WDM Single
mode SC type.
Support 8192 MAC addresses. Provides 2M bits memory buffer.
Operating voltage and Max. current consumption: 1.25A @ 12VDC,
0.625A @ 24VDC. Power consumption: 15W Max.
Power Supply: Redundant DC Terminal Block power inputs or 12VDC
DC JACK with 100-240VAC external power supply.
-40℉to 167℉(-40℃to 75℃) operating temperature range.
Tested for functional operation @ -40℉to 185℉(-40℃to 85℃).
Supports Din-Rail, Panel, or Rack Mounting installation.

Hardened Managed Ethernet Switch
5
Console Configuration
Connect to the switch console:
Connect the DB9 null-modem or cross over cable to the RS-232 serial
port of the device and the RS-232 serial port of the terminal or computer
running the terminal emulation application. Direct access to the
administration console is achieved by directly connecting a terminal or a
PC equipped with a terminal-emulation program (such as
HyperTerminal) to the switch console port.
Configuration settings of the terminal-emulation program:
Baud rate: 115,200bps
Data bits: 8
Parity: none
Stop bit: 1
Flow control: none.
Press the “Enter” key. The Command Line Interface (CLI) screen should
appear as below:
Logon to Exec Mode (View Mode):
At the “switch_a login:” prompt just type in “root” and press <Enter> to
logon to Exec Mode (or View Mode). And the “switch_a>” prompt will
show on the screen.
Logon to Privileged Exec Mode (Enable Mode):

Hardened Managed Ethernet Switch
6
At the “switch_a>” prompt just type in “enable” and press <Enter> to
logon to Privileged Exec Mode (or Enable Mode). And the “switch_a#”
prompt will show on the screen.
Logon to Configure Mode (Configure Terminal Mode):
At the “switch_a#” prompt just type in “configure terminal” and press
<Enter> to logon to Configure Mode (or Configure Terminal Mode). And
the “switch_a(config)#” prompt will show on the screen.

Hardened Managed Ethernet Switch
7
Web Configuration
Login the switch:
Specify the default IP address (192.168.1.10) of the switch in the web
browser. A login window will be shown as below:
Enter the factory default login ID: root.
Enter the factory default password (no password).
Then click on the “Login” button to log on to the switch.

Hardened Managed Ethernet Switch
8
Preface
This manual describes how to install and use the Hardened
Managed Ethernet Switch. This switch introduced here is
designed to deliver full scalability with SNMP/RMON
web-based management functions by providing:
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
Features on the Hardened Managed Ethernet Switch
Illustrative LED functions
Installation instructions
Management Configuration
SNMP, DHCP, IGMP…
Specifications

Hardened Managed Ethernet Switch
9
Table of Content
DIP Switch .................................................................................. 1
The 1000BaseT and 1000BaseSX/LX Connectors..................... 1
The Port Status LEDs................................................................. 1
Description ......................................................................... 1
Quick Start Guide .................................................................................................................... 2
Physical Description..........................................................2
The Port Status LEDs and Power Inputs .................................... 2
Functional Description...................................................... 4
Console Configuration.......................................................5
Web Configuration............................................................ 7
Preface .................................................................................................................................... 9
Table of Contents .................................................................................................................. 10
Product Overview .................................................................................................................. 13
Hardened Managed Ethernet Switch............................. 13
Package Contents............................................................. 13
Product Highlights........................................................... 14
Basic Features........................................................................... 14
Management Support................................................................ 15
Front Panel Display......................................................... 16
Physical Ports................................................................... 17
Switch Management ........................................................ 17
Web-based browser interface ................................................... 18
Administration console via RS-232 serial port (CLI)............... 18
External SNMP-based network management application ........ 18
Installation ............................................................................................................................. 19
Selecting a Site for the Switch......................................... 19
Connecting to Power........................................................ 19
DC Terminal Block power input.............................................. 19
12VDC DC Jack....................................................................... 19

Hardened Managed Ethernet Switch
10
Connecting to Your Network.......................................... 20
Cable Type & Length............................................................... 20
Cabling ..................................................................................... 20
Switch Management .............................................................................................................. 21
Management Access Overview....................................... 21
Administration Console (CLI)........................................21
Direct Access............................................................................ 22
Modem Access ......................................................................... 22
Web Management............................................................23
SNMP-Based Network Management............................. 23
Protocols........................................................................... 24
Management Architecture.............................................. 24
Web-Based Browser Management........................................................................................ 25
SNMP & RMON Management............................................................................................... 26
Overview........................................................................... 26
SNMP Agent and MIB-2 (RFC 1213)............................ 26
RMON MIB (RFC 1757) and Bridge MIB (RFC 1493)27
RMON Groups Supported........................................................ 28
Bridge Groups Supported......................................................... 29
Web-Based Browser Management........................................................................................ 30
Logging on to the switch..................................................30
Understanding the Browser Interface............................ 31
Trunking........................................................................... 45
STP.................................................................................... 48
VLAN................................................................................ 56
QoS.................................................................................... 61
SNMP................................................................................ 64
Other Protocols................................................................ 68
Command Line Console Management .................................................................................. 72

Hardened Managed Ethernet Switch
11
Administration Console................................................... 72
Exec Mode (View Mode)......................................................... 73
Privileged Exec Mode (Enable Mode) ..................................... 76
Configure Mode (Configure Terminal Mode).......................... 80
System............................................................................... 84
Port.................................................................................... 88
Switching .......................................................................... 92
Trunking........................................................................... 96
STP.................................................................................... 99
VLAN.............................................................................. 108
QoS.................................................................................. 112
SNMP.............................................................................. 114
Other Protocols.............................................................. 124
Specifications ...................................................................................................................... 130
Appendix.............................................................................................................................. 132
Contact Information...............................................................................................................133

Hardened Managed Ethernet Switch
12
Product Overview
Hardened Managed Ethernet Switch
Front View
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
•The Hardened Managed Ethernet Switch
•User’s Manual
•RS232 cable
•Panel-mount brackets with screws

Hardened Managed Ethernet Switch
13
Product Highlights
Basic Features
Complies with NEMA TS1 & TS2 Environmental requirements for Traffic
control equipment
Complies with EN61000-6-2 EMC Generic standard immunity for
Industrial environment
Supports 8192 MAC addresses
Provides 2M bits memory buffer
Auto-negotiation for speed and duplexity on all TX ports
Auto-MDIX on all TX ports
Full wire-speed forwarding rate
Store-and-forward mechanism
Half-duplex back-pressure and IEEE802.3x full-duplex compliant flow
control
Redundant power inputs: 12VDC (DC Jack) and 12 to 32VDC (Terminal
Block)
-40° F to 167° F (-40° C to 75° C) operating temperature range
Tested for functional operation @ -40℉to 185℉(-40° C to 85° C)
Front panel reset button
Front panel port status LEDs
Hardened aluminum case
Supports DIN-Rail, Panel, or Rack Mounting installation

Hardened Managed Ethernet Switch
14
Management Support
VLAN
Port-based VLAN
IEEE802.1Q tagged VLAN
TRUNKING
IEEE802.3ad Link Aggregation Control Protocol
MAC-based Trunking with automatic link fail-over
PORT-SECURITY
Per-port programmable MAC address locking
Up to 24 Static Secure MAC addresses per port
PORT-MIRRORING
Port-mirroring
QOS (IEEE802.1p Quality of Service)
4 priority queues
INTERNETWORKING PROTOCOLS
Bridging:
IEEE802.1s Multiple Spanning Tree
IEEE802.1w Rapid Spanning Tree
IEEE802.1D Spanning Tree compatible
IEEE802.1Q – GVRP
Recover-Ring(tm) capability
IP Multicast:
IGMP Snooping
Rate Control
NETWORK MANAGEMENT METHODS
Console port access via RS-232 cable (CLI, Command Line Interface)
Telnet remote access
SNMP agent:
MIB-2 (RFC1213)
Bridge MIB (RFC1493)
RMON MIB (RFC1757) – statistics, history, alarm and events
VLAN MIB (IEEE802.1Q/RFC2674)
Private MIB
Web browser
TFTP software-upgrade capability

Hardened Managed Ethernet Switch
15
Front Panel Display
POWER
This LED comes on when the switch is properly connected to power and
turned on.
Port Status LEDs
The LEDs are located at the left side of the front panel, displaying status
for each respective port. Please refer to the following table for more
details.
LED State Indication
10/100TX
On A valid network connection established
Link/ACT Flashing Transmitting or receiving data
ACT stands for ACTIVITY
On Communication speed is 100Mbps
10/100
Off Communication speed is 10Mbps
On Communication speed is 1000Mbps
1000
Off Communication speed is 10/100Mbps
On A valid network connection established
SFP Link
Off No valid network connection established

Hardened Managed Ethernet Switch
16
Physical Ports
The Hardened Managed Ethernet Switch provides:
12-port 10/100BaseTX + 2-port SFP/RJ-45 combo Gigabit
Hardened Managed Ethernet Switch
CONNECTIVITY
SC connectors on 1000SX/LX ports
RJ-45 connectors on TX ports
MODE SELECTION
10BaseT full-duplex mode
10BaseT half-duplex mode
100BaseTX full-duplex mode
100BaseTX half-duplex mode
1000BaseT/SX/LX full-duplex mode
Auto-negotiating mode

Hardened Managed Ethernet Switch
17
Switch Management
Web-based browser interface
The switch also boasts a point-and-click browser-based interface that lets
user access full switch configuration and functionality from a Netscape or
Internet Explorer browser.
Administration console via RS-232 serial port (CLI)
The switch provides an onboard serial port, which allows the switch to be
configured via a directly connected terminal.
External SNMP-based network management application
The switch can also be configured via SNMP.

Hardened Managed Ethernet Switch
18
Installation
This chapter gives step-by-step instructions about how to
install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
-The ambient temperature should be between -40° F to 167° F (-40° C to 75°
C).
-The relative humidity should be less than 95 percent, non-condensing.
-Surrounding electrical devices should not exceed the electromagnetic field
(RFC) standards.
-Make sure that the switch receives adequate ventilation. Do not block the
ventilation holes on each side of the switch.
Connecting to Power
DC Terminal Block power input
Step 1: Connect the supplied DC power cord to the terminal block on the back of the switch,
and then plug it into a standard DC outlet with a voltage range from 12 to 32 VDC. Turn on the
DC power supply.
Step 2: Turn off the DC power supply if you want to shut down the switch.
12VDC DC Jack
Step 1: Connect the supplied AC to DC power adapter to the receptacle on the back of the
switch.
Step 2: Connect the power cord to the AC to DC power adapter and attach the plug into a
standard AC outlet with the appropriate AC voltage.
Rear view

Hardened Managed Ethernet Switch
19
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when connecting the
switch to your network. Use appropriate cables that meet your speed and
cabling requirements.
Cable Specifications
Speed Connector Port Speed
Half/Full Duplex
Cable Max.
Distance
10BaseT RJ-45 10/20 Mbps 2-pair
UTP/STP
Cat. 3, 4, 5
100 m
100BaseTX RJ-45 100/200 Mbps 2-pair
UTP/STP
Cat. 5
100 m
1000BaseT RJ-45 2000 Mbps 4-pair
UTP/STP
Cat. 5
100 m
1000BaseSX
(*Wavelength of
850nm)
SC 2000 Mbps 50 or
62.5/125µm
multi-mode
fiber
550m
1000BaseLX
(*Wavelength of
1300nm)
SC 2000 Mbps 9 or
10/125µm
single-mode
fiber
50 km
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port in use.
Step 3: Consult Cable Specifications Table on previous page for cabling requirements based on
connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a desired device.
Step 5: Once the connections between two end devices are made successfully, turn on the power
and the switch is operational.

Hardened Managed Ethernet Switch
20
Switch Management
This chapter explains the methods that you can use to
configure management access to the switch. It describes the
types of management applications and the communication
and management protocols that deliver data between your
management device (workstation or personal computer) and
the system. It also contains information about port
connection options.
This chapter covers the following topics:
• Management Access Overview
• Key Concepts
• Key Guidelines for Implementation
• Web Management Access
• Administration Console Access
• SNMP Access
• Standards, Protocols, and Related Reading
Management Access Overview
The switch gives you the flexibility to access and manage
the switch using any or all of the following methods.
The web browser interface and administration console (CLI)
support are embedded in the switch software and are
available for immediate use.
Administration Console (CLI)
The administration console is an internal, character-oriented,
Command Line Interface (CLI) for performing system
administration such as displaying statistics or changing
option settings.
Using this method, you can view the administration console
from a terminal, personal computer, Apple Macintosh, or
workstation connected to the switch’s console port.