SignaMax 065-7508 User manual

User‘s Guide
8 Port Nway Fast Ethernet
Web Smart Switch
Model :065-7508

SIGNAMAX LLC • www.signamax.eu
FCC Warning
This device has been tested and found to comply with limits for a
Class B digital device, pursuant to Part 2 and 15 of FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates and
radiates radio frequency energy and, if not installed and used in
accordance with the user’s manual, it may cause interference in
which case users will be required to correct interference at their
own expenses.
CE Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference in which case the user may
be required to take adequate measures.

SIGNAMAX LLC • www.signamax.eu
Introduction
065-7508 switch provides 8 10/100M ports. 065-7508 switch was
designed for easy installation and high performance in an
environment where traffic is on the network and the number of
users increases continuously.
The small palm size with transparent plastic case was specifically
designed for small to medium workgroups. 065-7508 switch can
be installed where space is limited; moreover, it provides smooth
network migration and easy upgrade to network capacity.

SIGNAMAX LLC • www.signamax.eu
Package Contents
Before you start to install this switch, please verify your package
that contains the following items:
One 065-7508 Fast Ethernet Switch
One Power Adapter
One CD with User’s Manual
Note: If any of these items is found missing or damaged, please
contact your local supplier for replacement.

SIGNAMAX LLC • www.signamax.eu
Key Features
8 Port 10/100M Nway (Auto-negotiation) Switch
Palm size with plastic case
Auto-learn of networking configurations
Auto-detect full/half-duplex modes for any port
Dedicated full-duplex 200Mbps bandwidth
Store-and-Forward switching methods
IEEE 802.3x flow control for full-duplex and back-pressure
flow control for half-duplex
Non-blocking & Non-head-of-line blocking full wire speed
forwarding
Auto-MDI/MDI-X function for any port
Smart plug & play
Power
Power is supplied through an external DC power adapter.

SIGNAMAX LLC • www.signamax.eu
Front Panel (LEDs)
LED Indicators of 8 Port 10/100M Switch
LED Status Operation
On Power is on.Power
Off Power is off.
On Port is for connection
Off No connection.
LINK/ACT
Flashing
Data is transmitting or
receiving.
Rear Panel (Connections)
Switch/Hub to 065-7508 Fast Ethernet Switch
This switch provides automatic crossover detection functionality
for any port. It is simple and friendly to up-link to another switch
without crossover cable.

SIGNAMAX LLC • www.signamax.eu
PC/Other devices to 065-7508 Fast Ethernet Switch
Via a twisted pair cable straight through, this switch can be
connected to PCs, servers and other network devices.
Technical Specifications
Standards
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3x Flow control
Features
Number of Ports: 8
MAC Address: 1K
Buffer Memory: 512K bits
Transmission Method:
Store and Forward
Filtering/Forwarding
Rates
100Mbps port –
148,800pps
10Mbps – 14,880pps
Transmission Media
10BaseT Cat. 3, 4, 5
UTP/STP
100BaseTX Cat. 5
UTP/STP
LED Indicators Per Port: LINK/ACT
Per Unit: Power

SIGNAMAX LLC • www.signamax.eu
Power Supply DC 7.5V/0.8A
Power Consumption 6 Watts (Max)
Dimensions 140 x 105 x 25 mm (L x W
x H)
Weight 224 g
Operating
Temperature 0 to 55℃
Storage
Temperature -20 to 90℃
Humidity 10 to 90% RH
(non-condensing)
Certifications FCC Class B, CE
Web Smart Switch
Configure
Please follow the steps to configure this Web Smart switch.
Step 1:
Use a twisted pair cable to connect this switch to your PC.
Step 2:
Set your PC’s IP to 192.168.2.xx.

SIGNAMAX LLC • www.signamax.eu
Step 3:
Open the web browser (like IE…), and go to 192.168.2.1 site,
and then you will see the login screen.
Key in the user ID and the password to pass the
authentication,
IP: 192.168.2.1
ID: admin
Password: admin
After the authentication procedure, the home page shows up.

SIGNAMAX LLC • www.signamax.eu
Step 4:
On the following home page, select the configuration by
clicking the icon. It includes,
- Administrator
- Port Management
- VLAN Setting
- QoS Setting
- Port Security
- Logout

SIGNAMAX LLC • www.signamax.eu
Administrator: Authentication Configuration
You can change the user name and the password, and click
“Update” to confirm the new change. After that, you can reset
this switch by power off and then power on to take the new
user name and the password effectively.

SIGNAMAX LLC • www.signamax.eu
Administrator: System IP Configuration
You can change the IP address by typing the new IP address
and click “Update” to confirm the new change, and then the
message will show “Setting Process OK!!”, After that, you
should reset this switch by power off and then power on it to
complete the new change.

SIGNAMAX LLC • www.signamax.eu
Administrator: System Status
It shows this switch MAC address and system version. You
can change the new comment of this switch by typing the new
comment and click “Update” to confirm the new change.

SIGNAMAX LLC • www.signamax.eu
Administrator: Load Default Setting to EEPROM
You can click “Load” to load the factory default setting, and
then reset the switch by power off and then power on to take it
effectively.
Administrator: Firmware Update
Follow the instruction on the screen to update the new
firmware. Please contact with your sales agents to get the

SIGNAMAX LLC • www.signamax.eu
latest firmware information.
Port Management: Port Control Configuration
Select the “Port No.” which you want to configure the mode
below,
“Link Capability” – you can select the port is Auto-Nego, 10M or
100M mode
“Duplex” you can select the port is full or half-duplex mode.
“TX & RX” - you can enable/disable the port.
Note: The 1st port can’t be disabled.

SIGNAMAX LLC • www.signamax.eu
Port Management: Bandwidth Control
Select the “Port No.” which you want to configure the mode
below,
“TX Rate” is meant you can set the maximum transmission rate of
this selected port and choose the full speed or in
128K/256K/512K/1M/2M/4M/8M speed.
“RX Rate” is meant you can set the maximum receiving rate of
this selected port and choose full speed or in
128K/256K/512K/1M/2M/4M/8M speed.

SIGNAMAX LLC • www.signamax.eu
Port Management: Broadcast Storm Control
You can enable or disable the broadcast storm protection feature
by clicking “Update”.
Port Management: Max Packet Length
Select the maximum packet length setting, 1536 Bytes or 1522
Bytes for the switch.

SIGNAMAX LLC • www.signamax.eu
VLAN Setting: Group VLAN setting
There are 4 VLAN groups, 01, 02, 03, 04, can be used.
Select a group, and then click the port number which you want to
put it into the selected VLAN group.

SIGNAMAX LLC • www.signamax.eu
VLAN Setting: Multi to 1 Setting
This is a special design for easily setting the switch VLAN into
“VLAN Per Port“. After this setting, all ports can only connect to
the destination port.

SIGNAMAX LLC • www.signamax.eu
QoS Setting: Class of Service Configuration
You can set QoS mode of per port by different bases as below,
“Port Base” – you can select the port which you want to configure
as high priority and then the packets of the port will be firstly
transmitted.
“VLAN Tag/IP/DS” – you can select the port which you want to
configure as packets with special Tag/IP will be firstly
transmitted.