SignaMax 065-7408PTB User manual

HardenedPoEEthernetSwitch
1
Signamax™Connectivity Systems
Hardened Ethernet Switch
Model -065-7408PTB
065-7408P1FXSTTB
065-7408P1FXSCTB
065-7408P1FXSMTB
U SER ’ S G UIDE

HardenedPoEEthernetSwitch
2
Quick Start Guide
This quick start guide describes how to install and use the
Hardened PoE Ethernet Switch. This is the switch of choice
for harsh environments constrained by space.
Physical Description
The Terminal Block
Power Input Assignment
＋48VDC
Power2 －Power
Ground
＋48VDC
Power1 －Power
Ground
Earth
Ground
Terminal
Block
Relay Alarm Assignment

HardenedPoEEthernetSwitch
3
FAULT
*Relay warning signal disable for
following:
The relay contact closes if Power1
and Power2 are both failed but
Power3 on.
The relay contact closes if Power3
is failed but Power1 and Power2
are both on.
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch. Redundant
power supplies function is supported.
The 10/100BaseT/TX and 100BaseFX Connectors
1. The 10/100BaseT/TX Connections
The following lists the pinouts of 10/100BaseT/TX ports.
Pin Regular Ports Uplink port
1 Input Receive Data + Output Transmit Data +
2 Input Receive Data - Output Transmit Data -
3 Output Transmit Data + Input Receive Data +
4 NC NC
5 NC NC
6 Output Transmit Data - Input Receive Data -
7 NC NC
8 NC NC
2. The 100BaseFX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx

HardenedPoEEthernetSwitch
4
(receive) port of device I to the Tx (transmit) port of device II.
3. The WDM 100BaseFX Connections
The fiber port pinouts: Only one single-mode optical fiber is
required to transmit and receive data.
The Port Status LEDs

HardenedPoEEthernetSwitch
5
LED State Indication
10/100BaseT/TX, 100BaseFX
Steady A valid network connection established.
Link/ACT
(Green) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.

HardenedPoEEthernetSwitch
6
Functional Description
•Meets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
•Supports IEEE802.3af Power over Ethernet (PoE)
Power Sourcing Equipment (PSE).
•Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto
MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type, WDM
Single mode SC type.
•Supports 1024 MAC addresses. Provides 1M bits buffer
memory.
•Alarms for power and port link failure by relay output.
•Power Supplies: Redundant 48VDC Terminal Block
power inputs 100-240VAC external power supply.
•Operating voltage and Max. current consumption: 1.5A
@ 48VDC. Power consumption: 72W Max.
•-40 to 75 (℃℃-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40 to 85℃℃
(-40℉to 185℉).
•Supports DIN-Rail, Panel, or Rack Mounting
installation.
Assembly, Startup, and Dismantling
•Assembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.
•Startup: Connect the supply voltage to start up the
switch via the terminal block.
•Dismantling: Pull out the lower edge and then remove
the switch from the DIN rail.

HardenedPoEEthernetSwitch
7

HardenedPoEEthernetSwitch
8
Preface
A member of the growing Signamax family of rugged
switches, this Hardened PoE Ethernet Switch addresses a
need for a smaller switch. This switch provides an
affordable solution for rugged and outdoor environment,
transportation road-side cabinet, industrial floor shop,
multitenant dwellings or Fiber To The Home (FTTH)
applications. Capable of operating at temperature
extremes of -40°C to +75°C, this is the switch of choice for
harsh environments constrained by space.
Port 1 to port 4 on this Switch supports IEEE802.3af Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3af compliant Powered Device
(PD). Using external 48VDC power inputs through
Terminal Block, data and power can be transmitted to a
Powered Device (PD) over the same twisted-pair Ethernet
cable through port 1 to port 4 on the Switch.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
•Features on the switch
•Illustrative LED functions
•Installation instructions
•Specifications

HardenedPoEEthernetSwitch
9
Table of Contents
QUICK START GUIDE................................................................2
PHYSICAL DESCRIPTION ..............................................................2
The Terminal Block and Power inputs..............................2
The 10/100BaseT/TX and 100BaseFX Connectors ......3
The Port Status LEDs.........................................................4
FUNCTIONAL DESCRIPTION .........................................................6
ASSEMBLY,STARTUP,AND DISMANTLING....................................6
PREFACE......................................................................................8
TABLE OF CONTENTS..............................................................9
PRODUCT OVERVIEW.............................................................10
HARDENED POEETHERNET SWITCH ......................................... 10
PACKAGE CONTENTS.................................................................10
PRODUCT HIGHLIGHTS .............................................................. 11
Basic Features................................................................... 11
FRONT PANEL DISPLAY..............................................................12
PHYSICAL PORTS ....................................................................... 13
INSTALLATION..........................................................................14
SELECTING A SITE FOR THE SWITCH ..........................................14
DIN RAIL MOUNTING ...............................................................15
CONNECTING TO POWER ........................................................... 16
Redundant DC Terminal Block Power Inputs................16
Alarms for Power and Port Link Failure.............................17
CONNECTING TO YOUR NETWORK ............................................18
Cable Type & Length........................................................ 18
Cabling................................................................................19
SPECIFICATIONS......................................................................20
CONTACT INFORMATION.......................................................22

HardenedPoEEthernetSwitch
10
Product Overview
Hardened PoE Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3This Switch
3User’s Manual