SignaMax 065-7700 User manual

SignamaxConnectivity Systems
Hardened Managed PoE Ethernet Switch
Model -065-7700
U SER ’ S G UIDE

Hardened Managed PoE Ethernet Switch
User’s Manual 1
Quick Start Guide
This quick start guide describes how to install and use the
Hardened Managed PoE (Power over Ethernet) Ethernet
Switch. This is the switch of choice for harsh environments
constrained by space.
Physical Description
The Port Status LEDs and Power Inputs

Hardened Managed PoE Ethernet Switch
User’s Manual 2
LED State Indication
10/100BaseTX
LINK/ACT
Steady A valid network connection established.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
PoE Steady Power Device (PD) is connected.
Off Power Device (PD) is disconnected.
10/100BaseTX, 100BaseFX/BX SFP
LINK/ACT
Steady A valid network connection established.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
10/100/1000BaseTX, 1000BaseSX/LX/BX SFP
LINK/ACT
Steady A valid network connection established.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Power Input Assignment
Power3
47-57VDC
DC Jack
Power2 ＋
47-57VDC
Terminal
Block
－
Power Ground
Power1 ＋47-57VDC
－
Power Ground
Earth Ground
Relay Output Rating
1A @ 250VAC
Relay Alarm Assignment

Hardened Managed PoE Ethernet Switch
User’s Manual 3
FAULT
*Warning signal disable for following:
1.The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
2.The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.
Functional Description
Meets NEMA TS1/TS2 Environmental requirements such as
temperature, shock, and vibration for traffic control equipment.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
RS-232 console, Telnet, SNMP v1 & v2c & v3, RMON, Web Browser,
and TFTP management.
Supports Command Line Interface in RS-232 console.
Supports 8192 MAC addresses. Provides 2M bits memory buffer.
Port 1 ~ Port 4 support IEEE802.3at Power over Ethernet (PoE) Power
Sourcing Equipment (PSE) and/or Port 5 ~ Port 8 support IEEE802.3af
Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation,
1000Mbps-full-duplex, 10/100Mbps-full/half-duplex, Auto MDI/MDIX.
100BaseFX: Multi mode or Single mode duplex LC type. 100BaseBX:
WDM Multi mode or Single mode single LC type.
1000BaseSX/LX: Multi mode or Single mode duplex LC type.
1000BaseBX: WDM Multi mode or Single mode single LC type.
Store-and-forward mechanism. Full wire-speed forwarding rate.
Alarms for power and port link failure by relay output.
Power Supply: Redundant 47-57VDC Terminal Block power inputs or
47-57VDC DC Jack power input.
Field Wiring Terminal: Use Copper Conductors Only, 60/75℃, 12-24
AWG torque value 7 lb-in.
Operating voltage and Max. current consumption: 0.31A @ 48VDC.
Power consumption: Power consumption: 230W Max. (Full load with
PoE), 15W Max. (Without PoE).
-40℃to 75℃(-40℉to 167℉) operating temperature range. Tested for
functional operation @ -40℃to 85℃(-40℉to 185℉). UL508

Hardened Managed PoE Ethernet Switch
User’s Manual 4
Industrial Control Equipment certified Maximum Surrounding Air
Temperature @ 75℃(167℉).
For use in Pollution Degree 2 Environment.
Hardened metal case.
Supports Din-Rail or Panel Mounting installation.

Hardened Managed PoE Ethernet Switch
User’s Manual 5
Console Configuration
Connect to the switch console:
Connect the DB9 straight cable to the RS-232 serial port of the device
and the RS-232 serial port of the terminal or computer running the
terminal emulation application. Direct access to the administration
console is achieved by directly connecting a terminal or a PC equipped
with a terminal-emulation program (such as HyperTerminal) to the
switch console port.
Configuration settings of the terminal-emulation program:
Baud rate: 115,200bps
Data bits: 8
Parity: none
Stop bit: 1
Flow control: none
Press the “Enter” key. The Command Line Interface (CLI) screen should
appear as below:
Logon to Exec Mode (View Mode):
At the “switch_a login:”prompt just type in “root” and press <Enter> to
logon to Exec Mode (or View Mode). And the “switch_a>” prompt will
show on the screen.

Hardened Managed PoE Ethernet Switch
User’s Manual 6
Logon to Privileged Exec Mode (Enable Mode):
At the “switch_a>” prompt just type in “enable” and press <Enter> to
logon to Privileged Exec Mode (or Enable Mode). And the “switch_a#”
prompt will show on the screen.
Logon to Configure Mode (Configure Terminal Mode):
At the “switch_a#” prompt just type in “configure terminal” and press
<Enter> to logon to Configure Mode (or Configure Terminal Mode). And
the “switch_a(config)#” prompt will show on the screen.
Set new IP address and subnet mask for Switch:
At the “switch_a(config)#” prompt just type in “interface vlan1.1” and
press <Enter> to logon to vlan 1 (vlan1.1 means vlan 1). And the
“switch_a(config-if)#” prompt will show on the screen.
Command Syntax: “ip address A.B.C.D/M”. “A.B.C.D” specifies IP
address. “M” specifies IP subnet mask. “M”= 8: 255.0.0.0,
16:255.255.0.0, or 24: 255.255.255.0.
For example, At the “switch_a(config-if)#” prompt just type in “ip address
192.168.1.10/24” and press <Enter> to set new IP address
(192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch.

Hardened Managed PoE Ethernet Switch
User’s Manual 7
Web Configuration
Login the switch:
Specify the default IP address (192.168.1.10) of the switch in the web
browser. A login window will be shown as below:

Hardened Managed PoE Ethernet Switch
User’s Manual 8
Enter the factory default login ID: root.
Enter the factory default password (no password).
Then click on the “Login” button to log on to the switch.

Hardened Managed PoE Ethernet Switch
User’s Manual 9