SignaMax 065-7418POETB User manual

SignamaxConnectivity Systems
Hardened PoE
Ethernet Switch Series
USER’S GUIDE

SignamaxConnectivity Systems
Hardened PoE
Ethernet Switch Series
User’s Guide

SignamaxHardened PoE Ethernt Switch
User’s Manual 1
FCC Warning
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
may be required to take adequate measures.
SignamaxConnectivity Systems from Advanced Electronic
Supports Products Inc. All rights reserved. All brand names
are registered trademarks of their relative holders.
Trademarks
Product names mentioned in this manual may be trademarks
or registered trademarks of those products and are hereby
acknowledged.
•Ethernet is a trademark of Xerox Corporation.
•Microsoft Windows is a trademark of Microsoft Corporation.
•Signamaxis a trademark of Advanced Electronic Support Products,
Inc.

SignamaxHardened PoE Ethernet Switch
2User’s Manual
Quick Start Guide
This quick start guide describes how to install and use the
Hardened PoE Ethernet Switch. This is the switch of choice
for harsh environments.
Functional Description
•Meets NEMA TS1 & TS2 Environmental requirements: temperature,
shock, and vibration for traffic control equipment.
•Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
•Supports IEEE802.3at Power over Ethernet (PoE) Power Sourcing
Equipment (PSE).
•1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex, Auto-Negotiation,
Auto-MDI/MDIX.
•Supports 4096 MAC addresses. Provides 2.25M bits buffer memory.
•Alarms for power failure by relay output.
•Power Supplies: Redundant 47-57VDC Terminal Block power inputs.
•Operating voltage and Max. current consumption: 9A @ 55VDC. Power
consumption: 495W Max.
•-40℉to 167℉(-40℃to 75℃) operating temperature range. Tested for
functional operation @ -40℉to 185℉(-40℃to 85℃).
•Supports Rack Mounting installation.
Physical Description
The Port Status LEDs and Power Inputs

SignamaxHardened PoE Ethernt Switch
User’s Manual 3
LED
State
Indication
Power1
Power2
Steady
Power on.
Off
Power off.
Fault
Steady
Power redundant system failure occurred.
Off Power redundant system failure is not occurred.
10/100BaseTX
Link/ACT
Steady
A valid network connection established.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
10/100
Steady
Valid port connection at 100Mbps.
Off
Valid port connection at 10Mbps.
PoE
Steady
Powered device (PD) is connected.
Off
Powered device (PD) is disconnected.
LED
State
Indication
Gigabit Ethernet
Link/ACT
Steady
A valid network connection established.
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
TX
Steady
A valid TX connection established.
Off
No valid TX connection established.
SFP
Steady
A valid SFP connection established.
Off
No valid SFP connection established.
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch.
Redundant power supplies function is supported.
Power Input Assignment
Power2 ＋
47-57VDC
Terminal Block
－
Power Ground
Power1 ＋
47-57VDC
－
Power Ground
Earth Ground
Relay Output Rating
1A @ 24VDC
The 10/100BaseTX (PoE) and Gigabit Ethernet Connectors
1. The 10/100BaseTX (PoE) Connections
The following lists the pinouts of 10/100BaseTX ports.

SignamaxHardened PoE Ethernet Switch
4User’s Manual
Pin
Signal Name
Signal Definition
1
TD
＋
Output Transmit Data
＋
2 TD－Output Transmit Data －
3
RD
＋
Input Receive Data
＋
4
PoE
Positive (VCC+)
5
PoE
Positive (VCC+)
6
RD－Input Receive Data －
7
PoE
Negative (VCC-)
8
PoE
Negative (VCC-)
2. The 1000BaseT Connections
The following lists the pinouts of 1000BaseT ports.
Pin
Signal Name
Signal Definition
1
TP0
＋
Transmit and Receive Data 0
＋
2
TP0
－
Transmit and Receive Data 0
－
3 TP1＋Transmit and Receive Data 1 ＋
4
TP2
＋
Transmit and Receive Data 2
＋
5
TP2－Transmit and Receive Data 2 －
6
TP1
－
Transmit and Receive Data 1
－
7 TP3＋Transmit and Receive Data 3 ＋
8 TP3－Transmit and Receive Data 3 －
3. The SFP Socket Connections
The SFP socket for Gigabit fiber optic expansion.

SignamaxHardened PoE Ethernt Switch
User’s Manual 5
4. The 1000BaseSX/LX Connections
The fiber port pinouts: The Tx (transmit) port of device I is connected to the
Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx
(transmit) port of device II.
5. The WDM 1000BaseBX Connections
The fiber port pinouts: Only one optical fiber is required to transmit and
receive data.

SignamaxHardened PoE Ethernet Switch
6User’s Manual
Preface
This manual describes how to install and use the Signamax
Hardened PoE Ethernet Switch. A member of the growing
family of rugged switches, this Hardened PoE Ethernet
Switch provides an affordable solution for rugged and
outdoor environment, transportation road-side cabinet,
industrial floor shop, multitenant dwellings or Fiber To The
Home (FTTH) applications. Capable of operating at
temperature extremes of -40℉to 167℉(-40℃to 75℃), this
is the switch of choice for harsh environments.
Port 1 to port 16 on this Switch supports IEEE802.3at Power
over Ethernet (PoE) Power Sourcing Equipment (PSE) and
can detect an IEEE802.3at compliant Powered Device (PD).
Using external 47~57VDC power inputs through Terminal
Block, data and power can be transmitted to a Powered
Device (PD) over the same twisted-pair Ethernet cable
through port 1 to port 16 on the Switch.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
•Product overview
•Features on the Switch
•Illustrative LED functions
•Installation instructions
•Specifications

SignamaxHardened PoE Ethernt Switch
User’s Manual 7
Table of Contents
FCC WARNING.............................................................1
CE MARK WARNING.....................................................1
TRADEMARKS ...............................................................1
QUICK START GUIDE.....................................................2
FUNCTIONAL DESCRIPTION..................................2
PHYSICAL DESCRIPTION......................................2
PREFACE.......................................................................6
TABLE OF CONTENTS ....................................................7
PRODUCT OVERVIEW ....................................................8
HARDENED POEETHERNET SWITCH ....................8
PACKAGE CONTENTS..........................................8
PRODUCT HIGHLIGHTS........................................8
FRONT PANEL DISPLAY.......................................9
PHYSICAL PORTS .............................................10
INSTALLATION ............................................................11
SELECTING A SITE FOR THE EQUIPMENT .............11
CONNECTING TO POWER ...................................11
CONNECTING TO YOUR NETWORK......................12
SPECIFICATIONS..........................................................14
CONTACT INFORMATION .............................................16

SignamaxHardened PoE Ethernet Switch
8User’s Manual
Product Overview
Hardened PoE Ethernet Switch
Package Contents
When you unpack this product package, you will find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to our
authorized reseller.
•The Switch
•User’s Manual
Product Highlights
•Meets NEMA TS1 & TS2 Environmental requirements: temperature,
shock, and vibration for traffic control equipment.
•Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity
for industrial environment.
•Supports IEEE802.3at Power over Ethernet (PoE) Power Sourcing
Equipment (PSE).
•1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex, Auto-Negotiation,
Auto-MDI/MDIX.
•Supports 4096 MAC addresses. Provides 2.25M bits buffer memory.
•Alarms for power failure by relay output.
•Power Supplies: Redundant 47-57VDC Terminal Block power inputs.
•Operating voltage and Max. current consumption: 9A @ 55VDC. Power
consumption: 495W Max.
•-40℉to 167℉(-40℃to 75℃) operating temperature range. Tested for
functional operation @ -40℉to 185℉(-40℃to 85℃).
•Supports Rack Mounting installation.

SignamaxHardened PoE Ethernt Switch
User’s Manual 9
Front Panel Display
Status LEDs
LED
State
Indication
Power1
Power2
Steady
Power on.
Off
Power off.
Fault
Steady
Power redundant system failure occurred.
Off
Power redundant system failure is not occurred.
10/100BaseTX
Link/ACT
Steady
A valid network connection established.
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
10/100
Steady
Valid port connection at 100Mbps.
Off
Valid port connection at 10Mbps.
PoE
Steady
Powered device (PD) is connected.
Off
Powered device (PD) is disconnected.
LED
State
Indication
Gigabit Ethernet
Link/ACT
Steady
A valid network connection established.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
TX
Steady
A valid TX connection established.
Off No valid TX connection established.
SFP
Steady
A valid SFP connection established.
Off
No valid SFP connection established.

SignamaxHardened PoE Ethernet Switch
10 User’s Manual
Physical Ports
This switch series provides different combinations of RJ-45
copper and fiber ports as below:
•16 x 10/100BaseTX PoE ports + 2 x Gigabit Ethernet ports
•12 x 10/100BaseTX PoE ports + 2 x Gigabit Ethernet ports
•8 x 10/100BaseTX PoE ports + 2 x Gigabit Ethernet ports
Connectivity
•RJ-45 connectors
•SC or ST connector on 1000BaseSX/LX fiber port.
•SC connector on 1000BaseBX fiber port.
•SFP socket connection on 1000BaseSX/LX/BX fiber port.
<Note> Different product model supports different type of
fiber connector.

SignamaxHardened PoE Ethernt Switch
User’s Manual 11
Installation
This chapter gives step-by-step installation instructions about
how to install the Switch.
Selecting a Site for the Equipment
As with any electric device, you should place the equipment
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
•The ambient temperature should be between -40 to 167 degrees
Fahrenheit (-40 to 75 degrees Celsius).
•The relative humidity should be less than 95 percent, non-condensing.
•Surrounding electrical devices should not exceed the electromagnetic
field (RFC) standards.
•Make sure that the equipment receives adequate ventilation. Do not
block the ventilation holes on each side of the equipment.
•The power outlet should be within 1.8 meters of the product.
Connecting to Power
Redundant DC Terminal Block Power Inputs:
Redundant DC Terminal Block Power Inputs
There are two pairs of power inputs can be used to power up
this device. You only need to have one power input
connected to run the switch.
Step 1: Connect the DC power cord to the plug-able terminal block on the
switch, and then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the switch.
Alarms for Power Failure

SignamaxHardened PoE Ethernet Switch
12 User’s Manual
There are two pins on the terminal block are used for power
failure detection. Use this as a dry contact application to send
a signal for power failure detection.
Power Input Assignment
Power2 ＋
47-57VDC
Terminal Block
－
Power Ground
Power1 ＋
47-57VDC
－
Power Ground
Earth Ground
Relay Output Rating
1A @ 24VDC
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below when
connecting the switch to your network. Use appropriate
cables that meet your speed and cabling requirements.
Cable Specifications
Speed
Connector
Port Speed
Half/Full
Duplex
Cable
Max.
Distance
10BaseT RJ-45 10/20 Mbps 4-
pair UTP/STP
Cat. 3, 4, 5
100 m
100BaseTX
RJ-45
100/200 Mbps
4-pair UTP/STP
Cat. 5
100 m
1000BaseT RJ-45 2000 Mbps 4-
pair UTP/STP
Cat. 5
100 m
1000BaseSX
SC, ST
2000 Mbps
MMF (50 or
62.5μm)
275, 550 m
1000BaseSX
SC
2000 Mbps
MMF (50 or
62.5μm)
2 km
1000BaseLX
SC
2000 Mbps
SMF (9 or 10μm)
10, 20 km
1000BaseBX
SC
2000 Mbps
SMF (9 or 10μm)
20 km
SFP
1000BaseSX
Duplex LC
2000 Mbps
MMF (50 or
62.5μm)
275 m, 550
m, 2 km
1000BaseLX Duplex LC 2000 Mbps SMF (9μm) 10, 20, 40,
70 km
1000BaseBX Single LC 2000 Mbps
MMF (50 or
62.5μm)
550 m
1000BaseBX
Single LC
2000 Mbps
SMF (9μm)
10, 20 km

SignamaxHardened PoE Ethernt Switch
User’s Manual 13
Cabling
Step 1:First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port
in use.
Step 3:Consult the previous section for cabling requirements based on
connectors and speed.
Step 4:Connect one end of the cable to the switch and the other end to a
desired device.
Step 5:Once the connections between two end devices are made
successfully, turn on the power and the switch is operational.

SignamaxHardened PoE Ethernet Switch
14 User’s Manual
Specifications
Hardened PoE Ethernet
Switch
10/100BaseTX PoE ports with RJ-45
connectors, Gigabit Ethernet ports
Applicable Standards
IEEE802.3 10BaseT
IEEE802.3u 100BaseTX
IEEE802.3ab 1000BaseT
IEEE802.3z 1000BaseSX/LX
Switching Method Store-and-Forward
Forwarding Rate
10BaseT
100BaseTX
1000BaseT/SX/LX
10/20Mbps for half/full-duplex
100/200Mbps for half/full-duplex
2000Mbps for full-duplex
Performance 14,880pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
Cable
10BaseT
100BaseTX
1000BaseT
100BaseFX/BX
1000BaseSX/LX/BX
4-pair UTP/STP Cat. 3, 4, 5
4-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5
Up to 100m (328ft)
MMF (50 or 62.5μm), SMF (9 or10μm)
MMF (50 or 62.5μm), SMF (9 or10μm)
LED Indicators Per unit –
Power status (Power1, Power2), Fault
Per port –
10/100TX - Link/ACT, 10/100, PoE
Gigabit Ethernet - Link/ACT, TX, SFP
Dimensions
17.4” (W) x 8.07” (D) x 1.73” (H)
(442mm (W) × 205mm (D) × 44.2mm (H))
Net Weight
6.61lbs. (3Kg)
Power
Terminal Block: 47-57VDC
Operating Voltage &
Max. Current
Consumption
9A @ 55VDC
Power Consumption
495W Max.
Operating Temperature
-40
℉
~ 167
℉
(-40
℃
~ 75
℃
)
Tested for functional operation @
-40℉~ 185℉(-40℃~ 85℃)
Storage Temperature
-40
℉
~ 185
℉
(-40
℃
~ 85
℃
)
Humidity 5 ~ 95%, non-condensing
EMI
FCC Part 15, Class A
EN61000-5-4: EN55022

SignamaxHardened PoE Ethernt Switch
User’s Manual 15
EMS
EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated FRI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
Environmental Test
Compliance
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)
NEMA TS1/2 Environmental requirements for
traffic control equipment

SignamaxHardened PoE Ethernet Switch
16 User’s Manual
Contact Information
SIGNAMAXCONNECTIVITY SYSTEMS
An AESP Company
16295 N.W. 13h Avenue
Miami, Florida 33169, U.S.A.
Phone: [phone] Fax: [phone]
Sales: 800-446-2377 Tech. Support: 800-446-
2377, ext. 201
E-mail:
Http://www.signamax.com
[e-mail]