Silvercrest SFS 110 A1 User manual

IAN 115128
VACUUM SEALER SFS 110 A1
VACUUM SEALER
Operating instructions
VARILNI STROJČEK
Navodila za uporabo
ZGRZEWARKA DO FOLII
Instrukcja obsługi
FOLIENSCHWEISSGERÄT
Bedienungsanleitung

GB Operating instructions Page 1
PL Instrukcja obsługi Strona 15
SI Navodila za uporabo Stran 31
DE/AT/CH Bedienungsanleitung Seite 47
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

A
B
1
2
3
4
7
5
9
8
6
ewq
0
rt

1
GB
SFS 110 A1
Contents
Introduction...................................................2
Copyright............................................................... 2
Limitation of liability ....................................................... 2
Intended use ..................................................2
Package contents and transport inspection .........................3
Unpacking .............................................................. 3
Disposal of packaging materials ............................................. 3
Description of the appliance .....................................4
Technical data .................................................4
Safety guidelines ..............................................5
Setting up and connecting .......................................7
Set-up location requirements ................................................ 7
Electrical connection ...................................................... 7
Welding a tube film.............................................8
Vacuuming the tube film........................................10
Cleaning.....................................................12
Cleaning the appliance ...................................................12
Storage .....................................................12
Disposal .....................................................13
Notes on the Declaration of Conformity...........................13
Importer.....................................................13
Warranty....................................................14
Service ......................................................14

2
GB
SFS 110 A1
Introduction
Congratulations on the purchase of your new appliance!
You have decided in favour of a modern, high-quality product. These operating
instructions are part of this product. They contain important information on safety,
usage and disposal. Before using the product, familiarise yourself with all handling
and safety guidelines. This appliance may only be used as described and for the
purposes indicated. Please also pass these operating instructions on to any future
owner(s).
Copyright
This documentation is protected by copyright.
Any reproduction, or any reprint even in the form of excerpts, as well as the rendi-
tion of figures even in modified form, is only permitted with the manufacturer’s
written consent.
Limitation of liability
All the technical information, data and instructions regarding installation, connec-
tion and operation contained in these operating instructions corresponds to the
latest information available to us at the time of printing and takes our previous
experience and know-how into account.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no responsibility for damage caused by failure to
observe these instructions, improper use, incompetent repairs, unauthorised
modifications or for the use of non-approved replacement parts.
Intended use
This appliance is intended exclusively for the sealing and vacuum-packing of
foodstuffs in household quantities and only in private households. This device is
not intended for commercial or industrial applications or for continuous use.
It is not intended for any other use or use beyond that specified. Claims of any
kind for damage arising as a result of incorrect use will not be accepted.
The risk shall be borne solely by the user.

3
GB
SFS 110 A1
Package contents and transport inspection
The appliance is supplied with the following components as standard:
▯ Vacuum Sealer
▯ 1 x tube film
▯ These operating instructions
NOTE
► Check the package for completeness and for signs of visible damage.
► If the consignment is incomplete or damaged due to defective packaging
or carriage, contact the Service hotline (see the chapter Service).
Unpacking
♦ Remove the appliance, the tube film and the operating instructions from the
carton.
♦ Remove all packaging material.
♦ Remove the protective film from the control panel.
DANGER
► Packaging materials should not be used as a plaything. Risk of suffocation.
Disposal of packaging materials
The packaging protects the appliance from damage during carriage.
The packaging materials have been selected for their environmental friendliness
and ease of disposal, and are therefore recyclable.
Returning the packaging to the materials cycle conserves raw materials and
reduces the amount of waste that is generated. Dispose of packaging materials
that are no longer needed in accordance with applicable local regulations.
NOTE
► If possible, keep the original packaging during the warranty period so that
the device can be properly packed for returning in the event of a warranty
claim.

4
GB
SFS 110 A1
Description of the appliance
Figure A
Appliance lid
Suction tube
Cable retainer
Welding wire
Lower sealing ring
Rear limiters
Front limiters
Lid release
Upper sealing ring
Press seal
Figure B
-Red control lamp
3button (seal)
!button (stop)
.button (vacuum/welding)
0Green control lamp
Technical data
Operating voltage 220 - 240 V ∼, 50 Hz
Power consumption 110W
Protection class II/
Recommended operating time 20 seconds
Recommended break time 80 seconds

5
GB
SFS 110 A1
Safety guidelines
RISK OF ELECTRIC SHOCK
■ Prior to use, check the device for visible external damage.
Never operate an appliance that is damaged.
■ To avoid risks, arrange for a defective power cable to be
replaced by qualified technicians or by our Customer Service
Department.
■ NEVER use the appliance with a defective power cable.
■ Do not use extension cables or power socket strips that do not
meet the required safety standards.
■ Never open the appliance housing!
■ Remove the plug from the mains power socket before beginning
to clean the device.
■ Ensure that no moisture can penetrate the device during
cleaning.
RISK OF INJURY!
■ All repairs must be carried out by authorised specialist companies
or by the Customer Service department. Improper repairs may
result in a risk of injury to the user or damage to the appliance.
They will also invalidate any warranty claim.
■ The mains power socket must be easily accessible, so that the
power cable can be easily disconnected in the event of an
emergency.

6
GB
SFS 110 A1
RISK OF INJURY!
■ Cleaning and user maintenance must not be carried out by
children, unless they are aged 8 or over and are supervised.
■ The appliance and its connecting cable must be kept away
from children younger than 8 years old.
■ This appliance may be used by children aged 8 years and
above and by persons with limited physical, sensory or mental
capabilities or lack of experience and knowledge, provided
that they are under supervision or have been told how to use
the appliance safely and are aware of the potential risks.
■ Children must not play with the appliance!
■ Children should be supervised to ensure that they do not play
with the appliance.
■ Do not leave the appliance unsupervised when it is ready
for use. To prevent it being switched on accidentally, always
unplug the appliance after use or during breaks.
CAUTION – PROPERTY DAMAGE!
■ This appliance is not suitable for continuous use over long
periods. Let the appliance cool down for a minimum 80 sec-
onds after each vacuum process. The appliance could other-
wise be irreparably damaged!
■ Do not use an external timer switch or a separate remote
control system to operate the appliance.

7
GB
SFS 110 A1
Setting up and connecting
Set-up location requirements
For safe and trouble-free operation of the device , the set-up location must fulfil
the following requirements:
■ When setting it up, place the appliance on a firm, flat and horizontal
surface.
■ Do not place the device in a hot, wet or extremely damp environment or in
the vicinity of flammable materials.
■ The mains power socket must be easily accessible, so that the power cable
can be easily disconnected in the event of an emergency.
Electrical connection
CAUTION
► Before you connect the appliance, compare the connection data (voltage
and frequency) on the data plate with that of your mains power network.
These data must agree so that no damage is sustained by the device.
► Ensure that the power cable is undamaged and is not routed over hot
surfaces and/or sharp edges.
►Ensure that the power cable is not taut or kinked.
► Do not let the power cable hang over edges (trip wire effect).
♦ Insert the plug into the mains mains power socket.

8
GB
SFS 110 A1
Welding a tube film
NOTES ON THE FILM
► The film width may not exceed 28 cm. Otherwise it cannot be welded
correctly.
► Use only nylon-PE films with a structure (points or grooves) on one side and
that have a structure (points or grooves) on one side and a thickness of
approximately 0.17 - 0.29 mm (170 - 290 μ).
Otherwise the weld seam will not be tight and the appliance may be da-
maged. You can recognise films of this type from the information on the
packaging. The quality of the weld seam will vary depending on the type
and thickness of the film.
► The supplied film is suitable for temperatures between -20°C and +100°C.
1) Cut the desired length for your bag from the tube film using a pair of scissors.
Cut as straight as possible.
2) Open the appliance lid by pressing the lid release and opening the
lid upwards.
3) Lay the open end of the bag as far into the appliance so that the opening of
the bag is located centrally under the lower sealing ring . The bag should
be inserted no further than the rear limiters and must lie between the front
limiters . If the bag lies over one or both of the two limiters , then the
bag cannot be correctly welded.

9
GB
SFS 110 A1
NOTE
► The bag opening must lie flat on the welding wire . Otherwise the weld-
ing does not work properly.
4) Close the appliance lid . The press seal presses the bag onto the welding
wire , to create a smooth seam. Ensure that both corners of the appliance
lid click closed. If necessary, press them down once again on the markings
and so that the appliance lid clicks into place and locks shut.
5) Press the button 3. The red control lamp -lights up. As soon as the
sealing process is finished, the red control lamp -goes off.
NOTE
► You can halt the sealing process at any time by pressing the button !.
The red control lamp -goes out.
CAUTION – PROPERTY DAMAGE!
If the red control lamp -does not go out after a maximum of
10 seconds, there is a fault with the appliance.
► Remove the plug from the mains power socket immediately. Do not attempt
to repair the appliance yourself. Contact the Customer Service department.
6) Open the appliance lid by pressing the lid release and flipping the lid 
upwards. Remove the bag. This is now sealed at one end.
NOTE
► Ensure that the weld seam is properly closed. A correct weld seam should
be a smooth, straight stripe without any creases.
7) Fill the bag. You must leave at least 6 cm of the bag free up to the edge to
be welded.
CAUTION – PROPERTY DAMAGE!
► Fill the bag so that no food scraps or liquids can leak out during welding
and get into the appliance.
8) If you do not want to vacuum the bag, you can now weld the other, open side.

10
GB
SFS 110 A1
Vacuuming the tube film
You can also suck the air out of the bag (vacuum) during welding:
CAUTION – PROPERTY DAMAGE!
► Do not evacuate bags that contain liquids. These will get into the appliance
and damage it.
1) Lay the open end of the bag as far into the appliance so that the opening of
the bag is located centrally under the lower sealing ring . The bag should
be inserted no further than the rear limiters and must lie between the front
limiters . Otherwise the vacuuming and welding will not function correctly:
2) Close the appliance lid . Ensure that both corners of the appliance lid 
click closed. If necessary, press them down once again on the markings
and so that the appliance lid clicks into place and locks shut.
NOTE
► Ensure that the upper and the lower sealing rings are not damaged!
Otherwise the device cannot suck the air out of the bag.

11
GB
SFS 110 A1
3) Press the button .. The green control lamp 0lights up and the appli-
ance sucks the air out of the bag. As soon as all the air is sucked out, the red
control lamp -lights up. The appliance now seals the bag.
4) If both control lamps -/0have gone out, you can open the lid by pressing
the lid catch and flipping the lid upwards. Remove the vacuum-sealed
bag.
NOTE
► You can halt the air extraction process at any time by pressing the button !.
The green control lamp 0will then go off. Press the button .again to
resume the extraction process.
If the appliance has already switched to the sealing process and the red
control lamp -is lit, the process can be stopped with the button !.
The appliance then stops the sealing process.
TIP – "SOUS-VIDE COOKING"
► As the supplied film is suitable for temperatures between -20°C and
+100°C, it can be used for the so-called "sous-vide" cooking process
(vacuum cooking).
"Sous-vide" is French and means "under vacuum".
In vacuum cooking, the food (usually fish or meat, but vegetables can
also be used) is vacuum-sealed in a bag and then cooked in water or steam
cooked at a relatively low temperature (50 to 90 C). The advantage of this is
that volatile flavours or aroma are not lost during cooking. The food does not
dry out and the vitamins and flavours are preserved. Herbs or spices that are
vacuum-sealed in the bag with the food give off a more intense flavour.

12
GB
SFS 110 A1
Cleaning
DANGER
Risk of fatal injury from electrocution!
► Remove the plug from the mains power socket before beginning to clean
the device.
► Ensure that no moisture can penetrate the device during cleaning.
CAUTION
Possible damage to the appliance.
► Do not use aggressive or abrasive cleaning agents, as these may corrode
the surface of the casing.
► Do not use any hard or sharp objects to remove any adhesive from the
welding wire . Otherwise the welding wire or the insulation could
be damaged.
Cleaning the appliance
♦ Clean the surface of the housing of the appliance with a lightly moistened
cloth and a mild detergent.
♦ Wipe off the upper and the lower sealing rings , as well as the press
seal with a damp cloth. Ensure that the appliance is dry before using it
again.
Storage
The appliance has a built-in cable retainer on the underside of the housing,
on which you can wrap the power cable when it is not in use. This prevents the
power cable from getting caught or soiled, or becoming a source of danger by
hanging loosely down.
CAUTION
Possible damage to the appliance.
► Do not click the appliance lid closed for storage! When the appliance
lid is clicked closed it exerts permanent pressure on the upper and
lower sealing rings , as well as the press seal . This can negatively
affect their function.
♦ Store the appliance in a clean, dry place away from direct sunlight.

13
GB
SFS 110 A1
Disposal
Under no circumstances should you dispose of the appliance
with the normal household waste.
This product is subject to the provisions of European Directive
2012/19/EU (Waste Electrical and Electronic Equipment).
Dispose of the appliance via an approved waste disposal company or your
municipal waste disposal facility. Please observe applicable regulations. In
case of doubt, please contact your waste disposal centre.
Notes on the Declaration of Conformity
In regard to compliance with fundamental requirements and
other relevant provisions, this device complies with the Euro-
pean Electromagnetic Compatibility Directive 2004/108/EC,
RoHS Directive: 2011/65/EU, and the Low-Voltage Directive
2006/95/EC.
The complete Declaration of Conformity, in its original form,
is available from the importer.
Importer
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com

14
GB
SFS 110 A1
Warranty
You are provided a 3-year warranty on this appliance, valid from the date
of purchase. This appliance has been manufactured with care and inspected
meticulously prior to delivery.
Please retain your receipt as proof of purchase. In the event of a warranty claim,
please contact your Customer Service unit by telephone. This is the only way to
guarantee free return of your goods.
NOTE
► The warranty applies only to claims for material and manufacturing defects,
not for transport damage, wearing parts or for damage to fragile components,
e.g. bulbs or switches.
This appliance is intended solely for private use and not for commercial purposes.
The warranty shall be deemed void in cases of misuse or improper handling,
use of force and interventions which have not been carried out by one of our
authorised Service centres.
Your statutory rights are not restricted by this warranty.
The warranty period is not prolonged by repairs effected under the warranty.
This also applies to replaced and repaired components.
Any damage and defects present at the time of purchase must be reported im-
mediately after unpacking, but no later than two days after the date of purchase.
Repairs carried out after expiry of the warranty period shall be subject to charge.
Service
Service Great Britain
Tel.: [phone] (£ 0.10/Min.)
E-Mail: k[email protected]
IAN 115128
Hotline availability: Monday to Friday 08:00 - 20:00 (CET)

15
SFS 110 A1
PL
Spis treści
Wstęp.......................................................16
Prawaautorskie......................................................... 16
Ograniczenie odpowiedzialności ...........................................16
Użytkowanie zgodne z przeznaczeniem ..........................16
Zakres dostawy i przegląd po rozpakowaniu .....................17
Rozpakowanie..........................................................17
Utylizacja opakowania ................................................... 17
Opis urządzania ..............................................18
Dane techniczne ..............................................18
Wskazówki bezpieczeństwa ....................................19
Ustawianie i podłączanie ......................................21
Miejsca ustawienia urządzenia.............................................21
Podłączenie elektryczne ..................................................21
Zgrzewanie rękawa foliowego. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Pakowanie próżniowe z użyciem rękawa foliowego................24
Czyszczenie ..................................................26
Czyszczenie urządzenia ..................................................26
Przechowywanie .............................................26
Utylizacja....................................................27
Informacje dotyczące deklaracji zgodności ........................27
Importer.....................................................27
Gwarancja...................................................28
Serwis ......................................................28

16 SFS 110 A1
PL
Wstęp
Gratulujemy zakupu nowego urządzenia!
Jest to nowoczesny i wartościowy produkt. Instrukcja obsługi stanowi element
składowy produktu. Zawiera ona ważne informacje na temat bezpieczeństwa,
użytkowania i utylizacji. Przed rozpoczęciem użytkowania produktu należy
zapoznać się ze wszystkimi informacjami dotyczącymi obsługi i bezpieczeń-
stwa. Produkt należy użytkować wyłącznie zgodnie z zamieszczonym tu opisem
oraz w podanym zakresie zastosowań. W przypadku przekazania urządzenia
osobie trzeciej należy dołączyć również całą dokumentację.
Prawa autorskie
Niniejsza dokumentacja jest chroniona prawem autorskim.
Wszelkie rozpowszechnianie, wzgl. każdy przedruk, także we fragmentach,
jak również odtwarzanie ilustracji, także w zmienionym stanie, jest dozwolone
wyłącznie po uzyskaniu pisemnej zgody producenta.
Ograniczenie odpowiedzialności
Wszystkie zawarte w niniejszej instrukcji obsługi informacje techniczne, dane,
wskazówki montażu i podłączania oraz obsługi, są aktualne na dzień prze-
kazania do druku i uwzględniają nasze dotychczasowe doświadczenie oraz
spostrzeżenia zgodnie z najlepszą wiedzą.
Zawarte tu informacje, ilustracje i opisy nie mogą stanowić podstawy do roszczeń.
Producent nie ponosi żadnej odpowiedzialności za szkody spowodowane wskutek
nieprzestrzegania instrukcji, użytkowania urządzenia w sposób niezgodny z jego
przeznaczeniem, niefachowych napraw, niedozwolonych przeróbek lub użycia
niedozwolonych części zamiennych.
Użytkowanie zgodne z przeznaczeniem
Niniejsze urządzenie jest przeznaczone wyłącznie do zgrzewania i próżniowego
pakowania żywności w małych ilościach występujących w użytku domowym i tylko
w prywatnym gospodarstwie domowym. Urządzenie nie jest przeznaczone do
zastosowań przemysłowych ani profesjonalnych, jak również do pracy ciągłej.
Inne sposób użycia lub użycie wykraczające poza powyższy zakres uznaje się
za niezgodne z przeznaczeniem. Wszelkie roszczenia z tytułu szkód wynika-
jących z użytkowania niezgodnego z przeznaczeniem są wykluczone. Ryzyko
ponosi wyłącznie użytkownik.

17
SFS 110 A1
PL
Zakres dostawy i przegląd po rozpakowaniu
Urządzenie dostarczone jest standardowo z następującymi elementami:
▯ Zgrzewarka do folii
▯ 1 x rękaw foliowy
▯ Niniejsza instrukcja obsługi
WSKAZÓWKA
► Po rozpakowaniu nowego urządzenia sprawdź, czy w środku znajdują się
wszystkie części i czy nie ma żadnych widocznych uszkodzeń.
► W przypadku stwierdzenia braku lub uszkodzenia jakiegokolwiek elementu
wskutek wadliwego opakowania lub transportu skontaktuj się z infolinią
serwisową (patrz rozdział Serwis).
Rozpakowanie
♦ Wyjmij urządzenie, rękaw foliowy oraz instrukcję obsługi z kartonu.
♦ Usuń wszystkie części opakowania.
♦ Odklej folię z panelu sterowania.
NIEBEZPIECZEŃSTWO
► Elementów opakowania nie dawać dzieciom do zabawy. Istnieje niebez-
pieczeństwo uduszenia.
Utylizacja opakowania
Opakowanie chroni urządzenie przed uszkodzeniem podczas transportu.
Materiały opakowaniowe są przyjazne dla środowiska i można poddać je
procesowi recyklingu.
Przekazanie opakowania do ponownego przetworzenia pozwoli oszczędzić
surowce naturalne i zmniejszyć zanieczyszczenie środowiska. Zbędne opako-
wania utylizować zgodnie z lokalnymi przepisami.
WSKAZÓWKA
► W miarę możliwości zachowaj oryginalne opakowanie na czas trwania
gwarancji, by w razie odsyłania urządzenia móc je prawidłowo zapakować.