Wren Kitchens Vogue BASE UNIT 1000 2 Door User manual

BASE UNIT
1000 2 Door Assembly Guide
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev5.indd

Page 1
BASE UNIT
1000 2 Door Assembly Guide
L Bracket LGE
x2
Hinge Mounting
Plate
x4 Inc Screws
Hinge
x4 Inc Screws
Space Plug
x2
Panel B
x2 End Panel
Panel E
x2 Rail
Panel C
x1 Base Panel
Shelf
x1
Legs
x5
Frontal
(Packed
separately)
x2
Panel A
x1 Back Panel
(Folded)
Panel D
x1 Muntin
(F) x12
Wooden
Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x8
30mm
Screw
(J) x4
45mm
Screw Black
(L) x32
15mm
Screw
(N) x2
Door Buer
(Z) x5
Shelf Peg
Plastic
(M) x4
Cover Cap
REQUIRED TOOLS
NOT to be
used with CAM
DOWEL & CAM
LOCK
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev5.indd
Step 1.
Seat dowel (F)
into holes in
both end panels (B)
as shown.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do NOT use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
GG
GG GG
FF
FF GG FF
BB
G F F F F G
B
B
C
E
E
B
B
View from underside View from underside
H
G
G
H
Step 2.
Seat cam dowel (G) into
holes in both end panels (B)
as shown.
Seat (G)
cam dowel
into hole as
shown.
Step 3.
Attach panels (C) to panels (B),
using cam dowel (G) (in blue), and
also using dowels (F) (in orange)
in positions as shown.
Step 4.
Insert cam lock (H).
Do NOT tighten until Step 6.

Page 3
BASE UNIT
1000 2 Door Assembly Guide
Step 7.
Secure back panel (A) with 4 x 30mm screws (K) equally spaced at
the bottom of back panel (A) into base panel (C), as shown.
Ensure you screw into the centre of the base panels (C) (9mm from
the edge).
Step 5.
Slide back panel (A) into groove of end panels (B).
Once back panel (A) is in position, ensure the panel is ush & square
with bottom of end panels (B).
Step 6.
Hand tighten all cam locks (H), this will expand cam dowels (G) and
tighten the unit together.
Step 8.
Join muntin panel (D) to unit, use pilot holes to align muntin. Join
muntin panel (D), base panel (C) & rail panel (E) using 4 x 45mm
screws (J) as shown.
B
C
B
E
A
A
K
9mm
B
C
B
E
D
J
J
J
J

Page 4
For Internal Use: FI.WR.INS.022_WKIN00104_BASE_1000_2Door_Rev5.indd
Leg position diagram
C
B
B
Front
Front
Step 10.
Secure each of the legs into place with 4 x 15mm screws (L) per leg.
Step 11.
Push leg rmly down into leg base.
Adjust legs to 155mm before turning unit upright. Once in situ level
accordingly.
B
C
Step 9.
Position legs as shown. Ensure legs are rotated to also provide
support to the end panels (B).
L
L
L
L
B
C