Spectrum Industries 37257 User manual

Assembly Instructions
0106710R1 Page 1 of 3
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Cord Channel / Modesty Panel
for Flex Training Tables
(13) 044541
1/4-20 x 20mm
JC bolt
(1) 025039
4mm Hex
wrench
Installation - Cord Channel only
1. Flip the table upside-down onto a non-abrasive surface.
2. Remove the four rear-most PHM screws from each leg mounting plate.
3. Attach the front half of the cord channel to the worksurface (through the leg mounting plates) as shown
using 1/4-20 JC bolts and tighten securely. Figure 1.
4. Attach the rear half of the cord channel to the worksurface (through the leg mounting plates) as shown
using 1/4-20 JC bolts and tighten securely.
Note: The hole in the middle of the mounting ange does not require a JC bolt into the worksurface.
5. Align the cord channel mounting holes from both halves, and attach together with JC bolts.
Note: The rear half will overlap the front, and the JC bolts will thread into the front half.
Figure 1
Worksurface
Leg Mounting Plate
4mm Hex
wrench
(included)
Tools
Required
Cord Channel
37257 - for 60” table
37258 - for 72” table
Modesty Panel
37254 - for 60” table
37255 - for 72” table
Cord Channel Modesty Panel Cord Channel &
Modesty Panel
Front half of
cord channel
1/4-20 JC bolts
Rear half of
cord channel
Do not install
JC bolt here
(1) Rear Cord Channel
0106722 (72”)
0106719 (60”)
(1) Front Cord Channel
0106723 (72”)
0106720 (60”)
(1) Modesty Panel
0106721 (72”)
0106718 (60”)
(2) 0106717
Modesty Panel Brace
(One or both of the following may be included)

0106710R1 Page 2 of 3
Installation - Modesty Panel only
1. Flip the table upside-down onto a non-abrasive surface.
2. Remove the two rear-most PHM screws from each leg mounting plate.
3. Align the modesty panel mounting holes with the worksurface inserts
and attach (through the leg mounting plates) with 1/4-20 JC bolts as
shown. Figure 2.
Note: The hole in the middle of the mounting ange does not
require a JC bolt into the worksurface.
4. Orient the two modesty panel braces as shown, and secure with JC bolts.
5. Tighten all fasteners securely.
Figure 2
Worksurface
1/4-20 JC bolts
Modesty
Panel
Brace
Modesty Panel
Modesty
Panel Brace
Leg Mounting Plate

0106710R1 Page 3 of 3
925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
© 2016 Spectrum Industries Inc., All rights reserved.
Figure 3
Installation - Cord Channel and Modesty Panel
1. Flip the table upside-down onto a non-abrasive surface.
2. Remove the four rear-most PHM screws from each leg mounting plate.
3. Attach the front half of the cord channel to the worksurface (through
the leg mounting plates) as shown using 1/4-20 JC bolts and tighten
securely. Figure 3.
4. Attach the rear half of the cord channel to the worksurface (through the leg
mounting plates) as shown using 1/4-20 JC bolts and tighten securely.
5. Align the modesty panel mounting holes with the cord channel
mounting holes from both halves, and attach with JC bolts.
Note: The rear half of the cord channel will overlap the front half,
with the modesty panel attaching to both.
6. Orient the two modesty panel braces as shown, and secure with JC bolts.
7. Tighten all fasteners securely.
Worksurface
1/4-20 JC bolts
Modesty Panel
Modesty
Panel Brace
Leg Mounting Plate
Rear half of
cord channel
Front half of
cord channel
1/4-20 JC bolts
Modesty
Panel
Brace