Sime benchmark Planet Super 4 W. M. User manual

Planet
Super4W.M.
User Instructions
GB
PLEASE LEAVE THIS INSTRUCTION
WITH THE USER

1
BOILER IGNITION (fig. 1)
Open the gas cock, lower the cover of the
control and activate the boiler by turning
the selector knob to the summer ( ).
position. When the green led ( ) lights up,
electricity is present in the boiler.
– With the selector knob on the summer
( ) position, the boiler increases the
temperature of the hot water to the
set value.
– With the selector knob on the winter
position ( ) the boiler, once it has
reached the temperature set on the
heating potentiometer, will begin to mod
ulate automatically in order to supply the
system with the effective power request
ed. The boiler will stop functioning if the
room stat or “Logica Remote Control”
intercede.
TEMPERATURES ADJUSTMENT (fig. 2)
The panel of the red leds is graduated from
40÷80 °C and shows the temperature in
the D.H.W. tank when the two service leds
( ) are off; it shows the temperature
of the primary circuit when one of the two
leds is lit up.
– Regulation of the D.H.W. temperature is
carried out by acting on the hot water
service knob ( ). The set temperature
is displayed on the scale of the red leds
from 40 ÷80 °C.
– Regulation of the C.H. temperature is
carried out by acting on the heating knob
( ). The set temperature is shown on
the scale of the red leds from 40÷80 °C.
To guarantee an always optimal output
from the generator it is advised not to
go below a minimum operating tempera
ture of 50 °C.
TURNING OFF BOILER (fig. 1)
To turn the boiler off place the selector
knob on the OFF position.
IF THE BOILER IS NOT GOING TO BE
USED FOR A LENGTHY PERIOD IT IS
ADVISED TO TURN OFF THE ELECTRICI
TY SUPPLY, CLOSE THE GAS COCK, AND
IF LOW TEMPERATURES ARE FORESEEN,
EMPTY THE BOILER AND THE
HYDRAULIC SYSTEM TO AVOID FROST
DAMAGE.
CLEANING AND MAINTENANCE
T e programmed maintenance of t e
appliance must be carried out annually by
aut orised tec nical staff.
USER INSTRUCTIONS
LIGHTING AND OPERATION
REMOTE
CONTROL
R
APRE
SPIA VERDE
Fig. 1
GREEN LED
OPEN
VERY IMPORTANT!
PLEASE MAKE SURE YOUR LOG BOOK ENCLOSED IS FILLED IN CORRECTLY.
ALL CORGI REGISTERED INSTALLERS CARRY A CORGI ID CARD.
BOTH SHOULD BE RECORDED IN YOUR CENTRAL HEATING LOG BOOK.
YOU CAN CHECK YOUR INSTALLER IS CORGI REGISTERED
BY CALLING ON 01256 372300

2
FAULTS FINDING
–Ignition failure (fig. 3)
If the burner fails to start the red led will
light up ( ).
To attempt starting it again, the selector
knob must be turned to the position ()
and released soon after, returning to the
summer ( ) or winter ( ) position.
If t e failure s ould occur again, call
t e aut orised tec nical staff for
assistance.
–Insufficient water
pressure (fig. 4)
If the red led “0.5 bar” intermittently
lights up, the boiler is not functioning. To
restore functioning open the filling cock
until the green led “1 bar” lights up.
Once filled close t e filling tap.
If all the leds are off, call the authorised
technical staff.
–Safety stat interception (fig. 5)
If the safety stat intercedes the red led
“35°C” intermittently lights up. To start
the boiler again, turn the selector knob in
the position () and then release immedi
ately, returning it to the winter () or
summer ( ) function .
If t e failure s ould occur again, call
t e aut orised tec nical staff for
assistance.
SPIA ROSSA
Fig. 3
Fig. 4
SPIA ROSSA INTERMITTENTE
IN CONDIZIONE DI SICUREZZA
RED LED
FLASHING RED LED
IN SAFETY CONDITION
SPIA ROSSA INTERMITTENTE
Fig. 5
FLASHING RED LED
CLOSE

3
–Ot er faults (fig. 6)
When one of the leds is flashing from
“40÷ 80°C”, deactivate the boiler and
try to start it again. The operation may
be repeated 2 or 3 times, and if there is
no success call the authorised technical
staff for assistance.
When “ PLANET SUPER 4 W.M. ”is con
nected to the “Logica Remote Control”
regulator, the selector
CR/OFF/EST/INV/UNBLOCK must be
placed in the position ( ); the knobs of
the D.H.W. and C.H. potentiometers do
not have any effect and all of the func
tions will be managed by the regulator
(fig. 7).
If the “Logica Remote Control” breaks
down, the boiler will function by placing
the selector on the ( or ), posi
tion, obviously without consequent con
trol of the room temperature.
The functioning instructions are inside
the lid (fig. 8). Every setting or modifica
tion is displayed and confirmed on the
display (fig. 9).
LOGICA REMOTE CONTROL
1
67
8
4
5
3
2
KEY
1 Display
2 Info key
3 Operating mode key: automatic functioning
4 Operating mode key: manual functioning
5 Operating mode key: availability
6 Lid with instructions space
7 Temperature knob
8 On line key Fig. 8
KEY
1 Digits, hour
2 Heating programme
3 Unit (%/°C)
4 On line key display
5 External temperature
6 Room temperature
7 Vacation function
8 Operating mode
9 Line number, day
10 Burner lit
11 Heating functioning
12 Hot water temperature/load hot water Fig. 9
Fig. 7
Fig. 6
SPIA ROSSA INTERMITTENTE
FLASHING RED LED

4
If it is too hot or too cold in your apartment, you can easily adjust the fixed
temperature with the temperature knob.
Before adjusting it again, owever, allow t e temperature to stabilise first.
Note: With the temperature knob you can only adjust the fixed temperature, whilst the
reduced temperature remains the same.
–Adjusting t e temperature
If you turn the knob towards the + sign, the fixed temperature is
increased by about 1 °C for every notch.
If you turn the knob towards the sign, the fixed temperature is
decreased by about 1 °C for every notch.
Before adjusting t e temperature of t e Logica controller, t e t ermostatic valves, w ic
may be present, ave to be regulated to t e desired temperature.
For every operation of the Info key the follow
ing list of items, one after the other, are dis
played. The thermosensor continues to func
tion independently of the display.
Day, hour, room temperature
External temperature*
D.H.W. temperature*
* This data appear only if the relative sensor
is connected or if they are transmitted by
the regulator of the boiler.
–Info key
(reference key grey colour)
The operating mode desired is selected by
pressing the relative key with the correspond
ing symbol. The choice is displayed with the
symbol
Automatic functioning: the heating functions automatically according to the heat
ing programme entered. The programme may be excluded for brief periods with the
on line key.
Manual functioning: the heating functions manually according to the choice made
with the on line key.
Availability: the heating is deactivated.
–Selection of t e operating mode
(reference keys grey colour)
ACTIVATING
During operation t e lid of t e Logica controller must be closed.

5
If the rooms remain unused for a long period of time, the temperature
can be reduced with the on line key, in this way saving energy. When
the rooms are occupied again, press the on line key to re heat them.
The current choice is displayed on the display:
–On-line key
Fixed temperature heating
Reduced temperature heating
NOTA:
In automatic mode, the apparatus switches from the fixed temperature to the reduced tem
perature according to the temporal programme. The manual switching of the temperature is
done manually with the on line key.
–Temperature regulation
Fixed temperature:
temperature when the rooms are occupied
(basic setting)
Reduced temperature:
temperature during periods of absence or night
Comfort D.H.W. temperature:
desired temperature of domestic hot water
Reduced temperature of domestic hot water:
temperature desired for domestic hot water at reduced level.
To have access to the “reduced D.H.W. temperature” parameter, press the and
keys at the same time for at least 5 seconds and then go along the entered
lines with the key until parameter 61 is reached. Regulate the value with
and .
Before proceeding wit t e adjustment in t e temperature on t e Logica controller, t e t er-
mostatic valves, w ic may be present, ave to be regulated to t e desired temperature.
1
2
3
61
PROGRAMMING
For t e programming t e lid of t e regulator must be open.
As soon as the cover is open,
the display and the key functions
are switched on.
The number in the square rep
resents the programme lines
that may selected with the
arrow keys.
You can set or display the following values:
• Temperatures up to
• Heating programme up to
• Day of the week and hour up to
• Current values up to
• Vacation period
• Return to the default values
1 3
411
12 14
15 17
18
19
The choice made will work in a permanent way when manually , carried out, instead, if
automatic it will work up to the next switching according to the heating programme.

6
–D.H.W. programme
Select the days that correspond with the heating phase.
1= Monday, ... 7 = Sunday/8 = hot water service programme
Start of phase 1: heating with fixed modality
End phase 1: heating with reduced modality
Start phase 2: heating with fixed modality
End phase 2: heating with reduced modality
Start phase 3: heating with fixed modality
End phase 3: heating with reduced modality
Copying of the daily programme
By pressing this key it is possible to repeat the current heating programme
for the next day.
By pressing this key it is possible to repeat the current heating programme
for the previous day.
As a confirmation the following day is displayed.
4
5
6
7
8
9
10
11
With the Logica Remote Control it is possible to manage the temperature of D.H.W. tank on
two levels (a comfort level and one at reduced temperature) in accordance with the pro
gramme chosen with parameter 62 (load domestic hot water). To have access to the para
meter press the and keys for at least 5 seconds and then go along the entered lines
with the key until parameter 62 is reached. At this point four different programmes may
be selected with o keys, with the following characteristics:
0= 24 hours/ day Hot water is always available at the temperature set with user parame
ter n°3.
1= standard Hot water according to the daily heating programme.
In the comfort areas of heating the temperature of the D.H.W. tank is regulated to the
value set with user parameter n° 3.
In the reduced areas of heating the temperature of the D.H.W. tank is regulated to the
value set with parameter n° 61 of the service level.
2= service disconnected
3= second daily programme (8) Every day of the week the temperature of the hot water is set
according to programme 8. In this case there is a single programming for all the days of the
week and three time zones are available. In the time spans set the temperature of the D.H.W.
tank is regulated according to that set in parameter n°3. In the remaining hours the D.H.W.
tank is controlled to the temperature set with parameter n° 61 the of service level.
Start phase 1: preparation of the D.H.W. tank to the comfort temperature
End phase 1: Temperature of D.H.W. tank maintained at the reduced value
Start phase 2: Preparation of D.H.W. tank to the comfort temperature
End phase 2: Temperature of D.H.W. tank maintained at the reduced value
Start phase 3: preparation of D.H.W. tank to the comfort temperature
End phase 3: Temperature of D.H.W. tank maintained at the reduced value
5
6
7
8
9
10
–Heating programme With the heating programme it is possible to set the switching times of the temperature for a
period of a week. The weekly programme consists of 7 daily programmes. One daily pro
gramme allows 3 phases of heating. Each phase is defined by a ignition time and a finishing
time. The n° 8 daily programme is for the domestic hotwater service. If a period is not required,
the same ignition and finishing time may be entered.

7
1
0
–Display of t e functioning faults on t e display
Ignition failure
Turn the selector CR/OFF/EST/INV/UNBLOCK on the boiler control panel to the unblock posi
tion ( ) to restore functioning (fig. 3). If the failure should occur again, call the authorised tech
nical staff for assistance.
Safety stat interception
Turn the selector CR/OFF/EST/INV/UNBLOCK of the boiler control panel to the unblock posi
tion () to restore functioning (fig. 5). If the failure should occur again, call the authorised tech
nical staff
for assistance.
Air pressure switc failure
Call the authorised technical staff for assistance.
16
–Default values To take the setting to the default values, press the and keys at the
same time for at least 3 seconds. As confirmation a sign will appear on the display.
19
ATTENTION
The values of the following line numbers previously entered will be lost.
• Temperature and time programme to
• Vacation period
110
18
–Vacation function To enter the number of days of absence.
In the display the vacation symbol will be shown ( ), on the left the day of activa
tion (1 = Monday/7 = Sunday) and on the right the number of vacation days.
18
During the vacation the regulator will be on the availability mode.
When the set days have elapsed, the regulator will go on to the automatic function.
NOTE:
The vacation period may be cancelled by pressing a key of the operating mode.
–Current values Display and setting of the gradient of the heating characteristics curve.
When the room temperature set is not reached choose the gradient
indicated in point 2.10.3
Display of the current boiler temperature.
Display of the current power of the burner and of the current operating mode
( = = heating/ = D.H.W. service)
15
16
17
–Setting t e time To set the current day of the week
(1 = Monday/7 = Sunday)
To set the current hour
To set the current minute
Once the hour is completed, the setting of the hour changes.
12
13
14
With and keys the current hour is regulated. Pressing these keys together, the
regulation is speeded up in an increasing sense.

8
Air pressure switc does not return to rest position
Call the
authorised technical staff for assistance.
D.H.W. sensor fault (SB)
Call the
authorised technical staff for assistance.
66
67
68
69
70
192
193
194
195
C.H. sensor fault (SM)
Call the authorised technical staff for assistance.
Insufficient water pressure
Restore functioning by opening the filling cock of the boiler (fig. 4)
System overpressure
Call the
authorised technical staff
for assistance.
Safety stat interception
Call the
authorised technical staff for assistance.
Air pressure switc interception
Call the
authorised technical staff for assistance.
Failure of t e modulating coil
Call the
authorised technical staff for assistance.
Communication failure between t e Logica Remote Control and t e boiler
Call the
authorised technical staff for assistance.

Cod. 6274223A Documentation Dpt.
Sime Ltd
Unit D2 Enterprise Way, Bradford Road, Idle, Bradford, BD10 8EW
Tel. [phone] Fax [phone]
www.sime.ltd.uk e mail: [email protected]