SimpliFire SF-SCT43-BK User manual

1
SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/20
Scion Trinity Floating Mantel
SF-SCT43-MANTEL, SF-SCT55-MANTEL
Model: SF-SCT43-BK, SF-SCT55-BK
- Instructions -
Leave this manual with party responsible for use
and operation.
NOTICE! DO NOT discard this manual. Important service
and maintenance instructions included.
Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Needle-nose pliers
Hammer
Gloves
Level
Magnetic Phillips screwdriver
Safety glasses
Flat blade screwdriver
1/2 in. drill bit for 3/16 diameter toggle bolts (applicable if
installing on masonry walls)
Masonry drill bit 5/16 in. (applicable if installing on ma-
sonry walls)
Kit Components
• Mantel Bottom*
• Mantel Top*
• Mantel Side Panel (2)
• Side Bracket (2)
• Bottom Bracket (2)
• Front Bracket (1)
• ST4*12 Screws (6)
• ST4*8 Screw (4)
• ST6*50 Screw (8)
• M5*10 Screw (2)
• M6*16 Screws (8)
• 6*30 Wooden Dowels (8)
• 2-inch(51mm) cap. Top Mounting Trim
• Masonry Anchor (8)
• Wall Mount Bracket (1)
• Toggle Bolt Anchor (8)
* The Top and Bottom mantel pieces may be cong-
ured in either top or bottom positions depending on
the desired look.
The Floating Mantel is paint-ready with a white primer
nish.
SIDE BRACKET (2) BOTTOM BRACKET (2)
FRONT BRACKET (1)
Figure 1 Bracket

SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/202
APPLIANCE CENTERLINE
24 in.
(610 mm)
C
XX
B
A
ELECTRICAL
ACCESS ON
APPLIANCE
BOTTOM EDGE OF
WALL MOUNTING
BRACKET
MODEL X A B C D E
SF-SCT43-BK 24 in. (610 mm) 49-3/4 in. (1263 mm) 46-3/4 in. (1187 mm) 28 in.
(710 mm)
12-1/8 in.
(308 mm)
13-5/8 in.
(346 mm)
SF-SCT55-BK 28 in. (710 mm) 61-1/2 in. (1563 mm) 58-1/2 in. (1487 mm)
Figure 2 Mantel Dimensions and Receptacle Location
Refer to the appliance installation instructions to pre-
pare the appliance for the appropriate electrical wiring
conguration. If using the available plug-in wiring kit a
clearance hole may need to be cut into the appropriate
mantel section.
Appliance Location
If applicable, according to local electrical codes, the
oating mantel is able to conceal a horizontally install
wall receptacle behind the bottom mantel section. Refer
to Figure 2 to assist in locating the nal appliance and
mantel location in reference to the receptacle and/or
on the wall mounting bracket.
Note:
• The top of the oating mantel will be 24 inches
(610mm) from the bottom edge of the wall
mounting bracket.
• The mantel bottom will be able to conceal a
horizontal wall receptacle if the wall mounting
bracket’s bottom edge is located in line with the
receptacle’s standard size faceplate. The outlet
(including the standard size faceplate) must be
within 24 inches (610 mm) for the SF-SCT43-
BK and 28 inches (710 mm) for the SF-SCT55-BK,
of the desired nal appliance centerline.
NOTICE: The total weight of objects placed on the man-
tel shelf must not exceed 100 lbs (45 Kg).
D
E

3
SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/20
Figure 3 3/16 Toggle-Bolt Anchor
Framed Wall
• Locate the mounting bracket on the wall in the
desired location of the appliance. Level the bracket,
then mark its location on the wall, including a mark-
ing for each of the fastener holes in the bracket.
• For each of the marked mounting point locations,
determine which points align with a structural fram-
ing member. A minimum of two (2) locations must
be secured into a framing member.
• At the points where a wood or metal framing mem-
ber exists, the ST6X50 screw can be installed
directly into that structural member.
• For every mounting hole that does not align with a
structural framing member, a wall board toggle-bolt
anchor must be used. See Figure 3.
Direct Wall Mounting with Wall Mounting
Bracket
The wall mounting bracket can be installed on masonry
walls such as those constructed of brick or concrete,
or to framed walls constructed of wood or steel framing
sheathed with gypsum wallboard, drywall, wood, etc.
The method used to mount the mounting bracket is dif-
ferent between masonry walls and framed walls. Refer
to the following sections for more detail on the method
applicable to this installation.
• The toggle-bolt anchors are provided to accomodate
the required anchor points based on the appliance.
Use of toggle bolt anchors requires drywall thick-
ness of minimum 1/2 in. and drilled holes size of 1/2
in. diameter.
• Insert the bolt through the front side of the mounting
bracket and thread the toggle onto it from the rear of
the bracket. See Figure 4.
• Fold the toggle wings ush against the bolt and push
them through a drilled hole until the toggle wings
expand open on the other side. See Figure 5.
• Pull back on the bolt and tighten. See Figure 5.
Note: This product cannot be installed on a wall
sheathed with drywall less than 1/2 in. thick, unless
all six (6) anchor points in the mounting bracket
align with structural framing members.
NOTICE: Minimum eight (8) screws and/or toggle bolt
anchors are required for wall mounting.
Figure 5 Installing Anchors in Hollow Wall
Figure 4 Toggle Bolt Installation through Mounting Bracket
WARNING! Risk of Damage or Personal Injury! Al-
lowable pull-out and shear strength are 25% of ultimate
values or less, as required by building authorities.

SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/204
Wall
Masonry Anchors
Figure 6 Masonry Anchor Placement
WARNING! Risk of Damage or Personal Injury! Do
not use supplied masonry anchors on hollow walls,
sheathed with wood, gypsum wallboard, drywall or other
materials.
Figure 7 Bracket Attachment
Mounting Hooks
Point Up
Note: For non-masonry walls,
at least two mounting points
(screws ST6X50) must align
with structural framing member.
Appliance Installation
1. Hang appliance on the mounting bracket.
2. Align the slots on the back of the appliance with the
hooks on the top two corners of the bracket.
3. Hang the appliance and pull down to ensure the hooks
are fully engaged. See Figure 8.
4. Secure the appliance to the bracket with two M5X10
screws. See Figure 8.
1
2
Secure with screw on each
side of appliance.
Figure 8 Attaching Appliance to Bracket
Mounting Hooks
Point Up
Masonry Wall
• Locate the mounting bracket on the wall in the
desired location of the appliance. Level the bracket,
then mark its location on the wall, including a mark-
ing for each of the fastener holes in the bracket.
• In the marked locations, drill 5/16 in. diameter x 2 in.
deep holes. See Figure 6.
NOTICE: Minimum six (6) screws and anchors are
required for MASONRY wall mounting.
• Insert the provided wall anchors into the holes.
• Gently tap the anchors with a hammer until they are
ush with the wall surface.
• With mounting hooks pointed up, attach the bracket
to the masonry anchors with ST6X50 screws. See
Figure 7.

5
SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/20
2. Attach the two bottom brackets, one (1) on each
side to both sides of the appliance using four (4)
ST4*12 screws. See Figure 10.
Figure 9
ST4*12 SCREWS
1. Remove at side cover-plates by removing seven
(7) screws on each side. See Figure 9.
Re-use the screws removed from the cover-plates
to install the 2-inch (51mm) top mounting trim
pieces, provided with the mantel kit, on right and left
side of the appliance. See Figure 9. Continue by
installing the rear and bottom 2-inch (51mm) trim
pieces provided with the appliance.
Note: The bottom 2-inch trim has two extra
holes, as shown in Figure 9.
Figure 9
SCREW
LOCATION
2-inch (51 mm) TOP
MOUNTING TRIM
MOUNTING
HOLES
MOUNTING
HOLES
Mantel Installation
SIDE COVER PLATE
(both sides)
2-inch (51 mm)
BOTTOM MOUNTING
TRIM
2-inch (51 mm)
REAR TRIM
INCLUDED WITH
APPLIANCE (3
SCREWS)
Figure 11
3. Attach the front bracket to the appliance using two
(2) ST4*12 screws. See Figure 11.
FRONT
BRACKET
ST4*12 SCREWS
Figure 12
4. Position the bottom mantel between the bottom two-
inch (51 mm) trim and the bottom brackets and slide
into place. See Figure 12.
BOTTOM MANTEL
Note: The mantel top and bottom are reversible and
can be congured to your individual preference.

SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/206
Figure 14
Figure 15
7. Insert the four (4) wooden dowels into the open
holes of the bottom mantel. See Figure 15.
6. Secure the bottom mantel to the side brackets using
two (2) M6*16 screws. See Figure 14.
M6*16 SCREWS
(2 EACH SIDE)
SIDE
BRACKET
BOTTOM MANTEL
WOODEN DOWELS
(2 EACH SIDE)
Figure 16
8. Attach the mantel side panels to the bottom mantel
by aligning the holes in the mantel sides with the
dowels. See Figure 16.
MANTEL SIDE PANELS
Figure 13
5. Attach two (2) side brackets to the rear sides of the
appliance using four (4) ST4*8 screws. See Figure
13.
SIDE
BRACKET
BOTTOM MANTEL
ST4*8 SCREWS
(2 EACH SIDE)

7
SimpliFire • Scion Trinity Floating Mantel Instruction Manual • 2043-970 Rev. B • 9/20
Figure 17
Figure 18
Figure 19
9. Insert the two (2) wooden dowels on each side into
the open holes in the top of the mantel side panels.
See Figure 17.
10. Attach the mantel top to the mantel side panels by
aligning the holes in the mantel top with the dowels.
See Figure 18.
MANTEL TOP
11. Secure the top mantel to the side brackets using
two (2) M6*16 screws on each side. See Figure 19.
SimpliFire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
WOOD DOWELS
Figure 20 Wall Mount Weight Capacity
100 LBS
(45Kg)
The total weight of objects sitting on the mantel
shelf must not exceed 100 lbs (45 Kg).
Note: The mantel top and bottom are reversible and
can be congured to your individual preference.