Simrad GO XSE User manual

ENGLISH
GO XSE
Installation Manual
www.simrad-yachting.com


Preface
Disclaimer
As Navico is continuously improving this product, we retain the
right to make changes to the product at any time which may not be
reflected in this version of the manual. Please contact your nearest
distributor if you require any further assistance.
It is the owner’s sole responsibility to install and use the equipment
in a manner that will not cause accidents, personal injury or
property damage. The user of this product is solely responsible for
observing safe boating practices.
NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND
AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT
IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY
VIOLATE THE LAW.
Governing Language: This statement, any instruction manuals, user
guides and other information relating to the product
(Documentation) may be translated to, or has been translated from,
another language (Translation). In the event of any conflict between
any Translation of the Documentation, the English language version
of the Documentation will be the official version of the
Documentation.
This manual represents the product as at the time of printing.
Navico Holding AS and its subsidiaries, branches and affiliates
reserve the right to make changes to specifications without notice.
Copyright
Copyright © 2016 Navico Holding AS.
Warranty
The warranty card is supplied as a separate document.
In case of any queries, refer to the brand website of your unit or
system: www.simrad-yachting.com.
Compliance statements
This equipment complies with:
•CE under 2014/53/EU Directive
Preface | GO XSE Installation Manual 3

•The requirements of level 2 devices of the Radio communications
(Electromagnetic Compatibility) standard 2008
•Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
The relevant Declaration of conformity is available in the product's
section at the following website: www.simrad-yachting.com.
Industry Canada
IC RSS-GEN, Sec 7.1.3 Warning Statement- (Required for
license exempt devices)
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de
l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
Warning
The user is cautioned that any changes or modifications not
expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
4Preface | GO XSE Installation Manual

•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from
that of the receiver
•Consult the dealer or an experienced technician for help
Internet usage
Some features in this product use an internet connection to
perform data downloads and uploads. Internet usage via a
connected mobile/cell phone internet connection or a pay-per-MB
type internet connection may require large data usage. Your service
provider may charge you based on the amount of data you transfer.
If you are unsure, contact your service provider to confirm rates and
restrictions.
Countries of intended use in the EU
AT - Austria
BE - Belgium
BG - Bulgaria
CY - Cyprus
CZ - Czech Republic
DK - Denmark
EE - Estonia
FI - Finland
FR - France
DE - Germany
GR - Greece
HU - Hungary
IS - Iceland
IE - Ireland
IT - Italy
LV - Latvia
LI - Liechtenstein
LT - Lithuania
LU - Luxembourg
MT - Malta
Preface | GO XSE Installation Manual 5

NL - Netherlands
NO - Norway
PL - Poland
PT - Portugal
RO - Romania
SK - Slovak Republic
SI - Slovenia
ES - Spain
SE - Sweden
CH - Switzerland
TR - Turkey
UK - United Kingdom
Trademarks
Navionics®is a registered trademark of Navionics, Inc.
NMEA®and NMEA 2000®are registered trademarks of the National
Marine Electronics Association.
SiriusXM®is a registered trademark of Sirius XM Radio Inc.
Fishing Hot Spots®is a registered trademark of Fishing Hot Spots Inc.
Copyright© 2012 Fishing Hot Spots.
FUSION-Link™Marine Entertainment Standard™is a registered
trademark of FUSION Electronics Ltd.
C-MAP is a trademark of C-MAP.
SD™and microSD™are trademarks or registered trademarks of
SD-3C, LLC in the United States, other countries or both.
Wi-Fi®is a registered trademark of the Wi-Fi Alliance®.
Additional mapping data: Copyright© 2012 NSI, Inc.: Copyright©
2012 by Richardson’s Maptech.
Bluetooth®is a registered trademark of Bluetooth SIG, Inc.
HDMI®and HDMI™, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Navico product references
This manual refers to the following Navico products:
6Preface | GO XSE Installation Manual

•Broadband Sounder™ (Broadband Sounder)
•DownScan Imaging™ (DownScan)
•DownScan Overlay™ (Overlay)
•GoFree™ (GoFree)
•INSIGHT GENESIS® (Insight Genesis)
•SonicHub® (SonicHub)
About this manual
This manual is a reference guide for installing GO XSE units.
Important text that requires special attention from the reader is
emphasized as follows:
ÚNote: Used to draw the reader’s attention to a comment or
some important information.
Warning: Used when it is necessary to warn
personnel that they should proceed carefully to
prevent risk of injury and/or damage to equipment/
personnel.
Preface | GO XSE Installation Manual 7

8Preface | GO XSE Installation Manual

Contents
11 Check the contents
11 GO5 XSE box contents
12 GO7 XSE and GO9 XSE box contents
13 Overview
13 Front controls
14 Rear connections
15 Card reader
17 Installation
17 Mounting location
18 Bracket mounting
20 Panel mounting
21 Transducer installation
22 Wiring
22 Guidelines
23 Power Connections
24 Power Control connection
25 External alarm
26 Connecting control devices
26 NMEA 2000 backbone
28 CZone connection to NMEA 2000
29 Transducer connection
29 Radar connector
31 Software Setup
31 First time startup
31 Time and Date
31 Data source selection
33 Device list
34 Sonar setup
35 StructureScan
35 Radar setup
40 Autopilot setup
52 Fuel setup
55 CZone setup
57 Wireless setup
Contents | GO XSE Installation Manual 9

61 NMEA 2000 setup
61 Software updates and data backup
66 Accessories
68 Supported data
68 NMEA 2000 compliant PGN List
73 Technical specifications
73 Mechanical/Environmental
73 Electrical
74 Interfaces
75 Dimensional drawings
75 GO5 XSE Dimensional drawings
75 GO7 XSE Dimensional drawings
76 GO9 XSE Dimensional drawings
10 Contents | GO XSE Installation Manual

Check the contents
Check the contents of the box for your unit.
GO5 XSE box contents
ENGLISH
Installation Manual
bandg.com
ENGLISH
Installation Manual
bandg.com
ENGLISH
Installation Manual
bandg.com
ENGLISH
Installation Manual
bandg.com
1
2
4
5
6
7
10
9
11
8
3
1GO5 XSE
2Sun cover
3Panel mount gasket
4Cap (2x on NMEA 2000 and Sonar connectors)
5Fuse holder (ATC blade)
6Fuse (3 amp)
7Power/NMEA 2000 cable
8Panel mount screws (4x #10 x 1/2" PN HD SS)
9Quick Release Bracket screws (4x #10 x 3/4" PN HD SS)
10 Quick Release Bracket
11 Documentation pack
1
Check the contents | GO XSE Installation Manual 11

GO7 XSE and GO9 XSE box contents
ENGLISH
Installation Manual
bandg.com
ENGLISH
Installation Manual
bandg.com
ENGLISH
Installation Manual
bandg.com
ENGLISH
Installation Manual
bandg.com
1
2
4
5
6
7
10
9
12 11
8
3
1GO XSE
2Sun cover
3Panel mount gasket
4Caps (2x, on NMEA 2000 and Sonar connectors). The GO9
XSE has an additional cap for the Radar connector.
5Fuse holder (ATC blade)
6Fuse (3 amp)
7Power cable
8Panel mount screws (4x #10 x 1/2" PN HD SS)
9U Bracket mount screws (4x #10 x 3/4" PN HD SS)
10 U Bracket
11 Bracket knobs (2x)
12 Documentation pack
12 Check the contents | GO XSE Installation Manual

Overview
The unit has a built-in CHIRP/Broadband and StructureScan sonar.
The unit can network over NMEA 2000, this allows access to sensor
data.
The unit has built-in high speed GPS receiver (10Hz) and supports
Insight charts from Navico including Insight Genesis. The system
also supports charts from Navionics and C-MAP as well as content
created by a variety of third party mapping providers in the AT5
format. For a full selection of available charts, visit
www.gofreemarine.com, www.c-map.com or www.navionics.com.
The unit may be mounted to the vessel with the supplied mounting
bracket, or panel mounted on the dash.
The unit is intended for 12 V DC operation and will accept the
moderate fluctuations commonly seen in DC systems.
Front controls
1 Touch screen
2 Power button
Press and hold to turn the unit ON/OFF.
Press once to display the System Controls dialog.
2
Overview | GO XSE Installation Manual 13

Rear connections
GO5 XSE rear connections
1 2 3
1 Sonar - CHIRP, Broadband, DownScan, and SideScan
imaging (dependent on the transducer)
2 Card reader
3 Power 12 V DC supply input and NMEA 2000
GO7-XSE rear connections
NMEA2000 POWER SONAR
123
4
1 NMEA 2000 - data input / output
2 Power - 12 V DC supply input
14 Overview | GO XSE Installation Manual

3 Sonar - CHIRP, Broadband, DownScan, and SideScan
imaging (dependent on the transducer)
4 Card reader
GO9-XSE rear connections
1234
5
RADAR NMEA2000 POWER SONAR
1 Radar - radar (Ethernet) connection
2 NMEA 2000 - data input / output
3 Power - 12 V DC supply input
4 Sonar - CHIRP, Broadband, DownScan, and SideScan
imaging (dependent on the transducer)
5 Card reader - dual slot
Card reader
Used for attaching a microSD memory card. The memory card can
be used for detailed chart data, software updates, transfer of user
data, and system backup.
The card reader door is opened by pulling the rubber cover open.
The card reader door should always be securely shut immediately
after inserting or removing a card, in order to prevent possible water
ingress.
Overview | GO XSE Installation Manual 15

CardreaderontheGO5XSE CardreaderontheGO7XSEandGO9XSE
16 Overview | GO XSE Installation Manual

Installation
Mounting location
Choose the mounting locations carefully before you drill or cut. The
unit should be mounted so that the operator can easily use the
controls and clearly see the screen.
The unit has a high-contrast screen and is viewable in direct
sunlight, but for best results install the unit out of direct sunlight.
The chosen location should have minimal glare from windows or
bright objects.
Ensure that any holes cut are in a safe position and will not weaken
the boat’s structure. If in doubt, consult a qualified boat builder, or
marine electronics installer.
Before cutting a hole in a panel, make sure that there are no hidden
electrical wires or other parts behind the panel.
Check that it is possible to route cables to the intended mounting
location.
Consider access to the card reader which is located in the back of
the unit.
Leave sufficient clearance to connect all relevant cables.
Do not mount any part where it can be used as a hand hold, where
it might be submerged, or where it will interfere with the operation,
launching, or retrieving of the boat.
The mounting location may affect the internal GPS receiver. Test the
unit in its intended location to ensure satisfactory reception. An
external GPS source can be added to overcome poor reception
areas.
For overall width and height requirements, refer to "Dimensional
drawings" on page 75.
Good ventilation is required. Choose a location that will not expose
the unit to conditions that exceed the specifications - refer to
"Technicalspecifications" on page 73.
3
Installation | GO XSE Installation Manual 17

Warning: When installing, ensure appropriate safety
equipment is used. For example, ear muffs, protective
glasses, gloves and a dust mask. Power tools may
exceed safe noise levels, and can cast off dangerous
projectiles. The dust from many materials commonly
used in boat construction may cause irritation or
damage to eyes, skin, and lungs.
Bracket mounting
Quick release bracket mounting
The GO5 XSE can be mounted with the quick release bracket.
1. Place the bracket in the desired mounting location. Ensure that
the chosen location has enough height to accommodate the
unit fitted in the bracket, allows tilting of the unit and
connecting cables in the back.
ÚNote: Ensure that the chosen location has enough height to
accommodate the unit fitted in the bracket, allows tilting of the
unit and connecting cables in the back.
2. Mark the screw locations using the bracket as a template, and
drill pilot holes.
ÚNote: Use fasteners suited to the mounting surface material. If
the material is too thin for self-tappers, reinforce it, or mount
the bracket with machine screws and large washers. Use only
304 or 316 stainless steel fasteners.
3. Screw down the bracket.
4. Snap the unit to the bracket.
18 Installation | GO XSE Installation Manual

5. Tilt the unit to the desired position angle.
Removing the unit from the quick release bracket
Pull and hold the release handle and then pull the unit from the
bracket.
U-bracket mounting
The GO7 XSE and GO9 XSE can be mounted with the U-bracket.
Installation | GO XSE Installation Manual 19

1. Place the bracket in the desired mounting location. Ensure that
the chosen location has enough height to accommodate the
unit fitted in the bracket, and allows tilting of the unit. Also
adequate space is required on both sides to allow tightening
and loosening of the knobs.
2. Mark the screw locations using the bracket as a template, and
drill pilot holes. Use fasteners suited to the mounting surface
material. If the material is too thin for self-tappers, reinforce it, or
mount the bracket with machine screws and large washers. Use
only 304 or 316 stainless steel fasteners.
3. Screw down the bracket.
4. Mount the unit to the bracket using the knobs. Hand tighten
only. The ratchet teeth in the bracket and unit case ensure a
positive grip and prevent the unit from changing from the
desired angle.
Panel mounting
The screws and gasket used for panel mounting are included in the
box. For mounting instructions, refer to the Panel mounting
template.
20 Installation | GO XSE Installation Manual
Other manuals for GO XSE
6
Table of contents
Other Simrad Marine GPS System manuals

Simrad
Simrad HS70 User manual

Simrad
Simrad NSE8 User manual

Simrad
Simrad AP48 User manual

Simrad
Simrad NSS evo3 User manual

Simrad
Simrad Maris ECDIS900 User manual

Simrad
Simrad HS75 User manual

Simrad
Simrad NSS12 User manual

Simrad
Simrad HS52 User manual

Simrad
Simrad HS80 User manual

Simrad
Simrad Maris ECDIS900 User manual

Simrad
Simrad Simrad CS68 User manual

Simrad
Simrad CX34-DE NavStation User manual

Simrad
Simrad HS70 User manual

Simrad
Simrad NSS evo2 User manual

Simrad
Simrad CR34 User manual

Simrad
Simrad NSS evo2 User manual

Simrad
Simrad HS60 User manual

Simrad
Simrad AP70 User manual

Simrad
Simrad CS66 Operating and maintenance instructions

Simrad
Simrad GN70 User manual