Form
#
ZCE567A
Model
5979A
118"
(3
rnm)
PencilAir DieGrinder
ManufacturerISupplier
SiouxTools, Inc.
250 Snap-on Drive
P.O. Box 1596
Murphy,NC28906
Operator Instructions
Includes
-
Foreseen Use,
Work
Stations, Putting Into Service,
Operating, Dismantling,Assembly and Safety Rules.
ProductType
RPM
118"
(3
mm)
Pencil
Cycles
Per
~m
Air Die Grinder
Important
Read these instructions carefully before installing, operating,
servicingor repairingthistool. Keeptheseinstructionsina safe
accessibleplace.
U.S.A.
Tel No. 828-835-9765 Fax No. 828-835-9685
1
5979A
Model No/Nos
I
Serial No.
Air Pressure
ProductNetWeight
0.44
Ibs
0.20
Kg
RecommendedWorking
6.2
bar
90
PSI
Maximum
6.2
bar
90
PSI
RecommendedUseOf
BalancerOr Support
NO
Test Method:
Tested inaccordance with Pneurop
test code PN8NTC1 and IS0Standard 3744
RecommendedHoseBore
Size
-
Minimum
5/16
ins
8
mm
SAFETY MESSAGES
Personal
Safety
Equipment
Use
-
Safety
lasses
YES
Use
-
Safety Gloves
YES
Use
-
Safety Boots
Use
-
BreathingMasks
YES
Use
-
Ear Protectors
YES
RecommendedMax.
HoseLength
30Ft
10M
A
WARNING
Always
Read
Instructions
Before
Using
PowerTools
NoiseLevel:
Sound Pressure Level 72.0 dB(A)
Sound Power Level 84.0 dB(A)
@
Always Wear
Safety
Goggles
@
Wear
Hearing
Protection
Avoid
Prolonged
Exposure
To
Vibration
Safety ruleswhen using
5979A
pencil Die Grinder
-Use accessories rated at least
70,000
RPM.
-
Prolonged exposure to vibration may cause injury.
-Read all instructions before using this tool. All
operators must be fully trained in its use and aware of
these safety rules.
-
Do not exceed the maximumworking air pressure.
-
Use personal protection equipment as recommended.
-
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicalsknownto cause cancer,birthdefectsandother
reproductiveharm.
-Use only compressed air at the recommended
conditions.
-If the tool appears to malfunction, remove from use
immediately and arrange for service
Vibration Level
2.0
Meters
/
Sec2
Test Method:
Tested inaccordancewith IS0
standards8662 Parts 1
&
13
chance of coming into contact with live electricity.
-
Alwayswhen usingthe tool, adopt afirmfooting and/or
position and grip the tool sufficiently only to overcome
any reaction forces that may result from the tool doing
work. Do not overgrip.
-Use only correct spare parts for maintenance and
repair. Do not improvise or make temporary repairs.
Majorservicing and repairs should only be carried out
by persons trained to do so.
-
Do not lock, tape, wire, etc. the 'On/Off9valve in 'On'
position.The triggerllever, etc. must always be free to
return to the 'Off'position when released.
-Always shut off the air supply to the tool and press the
'OnIOff valve to exhaust the air from the feed hose
before fitting, removing or adjusting the working
attachment fitted tothe tool.
-
Beforeusingthe tool, make sure that a shut off device
and repair. If it is not practical to
remove tool from service, then shut
off the air supply to the tool and write
or have written a warning note and
attach itto the tool.
-
If tool isto be usedwitha balanceror
other suspension device, ensurethat
the tool is firmly attached to the
Easy
To
Reach
And
Air
Tool
suspensionlsupport device.
Operate
Shut
Off
Valve
-When operatingthe tool, alwayskeep
the body and particularly the hands
away from the working attachment
fixed to the tool.
-The tool is not electrically insulated.
Never use the tool if there is any
Page No
1
