Sirius Range Hoods SUT900 User manual

INSTALLATION
INSTRUCTIONS
CARE AND USE MANUAL FOR:
BUILT-IN RANGE HOODS
Models covered by this instructions:
SU900 -SUT900 - SUE900 - SU901 - SU902 - SU903
SU908 - SU906 - SU913
*** BEFORE INSTALLATION ***
ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED
DURING SHIPPING
*** SHIPPING DAMAGE ***
MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

WARNING
Thank you for purchasing a Sirius Range Hood.
Please read all the instructions in this manual before
installing the appliance.
Save these instructions for future reference.
Only use this appliance as an exhaust ventilation system for the removal of
cooking vapors. DO NOT use to expel ammable substances or any other
materials or vapors.
The installation procedures in this manual are intended for qualied instal-
lers, service technicians or persons with similar qualied background.
DO NOT attempt to install this appliance yourself.
Ensure that electrical power is turned o at source before commencing in-
stallation. All electrical wiring must be properly installed, insulated and
grounded and conform to all applicable codes and standards.
Make sure all existing duct work is clean of grease build up, or duct work
should be replaced, if necessary, to avoid the possibility of a grease re.
Check all joints on ductwork to ensure proper connection and all joints
should be properly taped. Be careful when cutting through ceilings or walls
not to damage any hidden pipes or electrical wiring. Ensure your kitchen has
sucient air return vents to replace the exhausted air.
Fan ducts should always be vented to the outside of your home and never
into spaces within walls, ceilings, lofts or attics. Only use rigid, smooth
steel for ducting. The exhaust point of the blower requires a 6” or 8” round
connection.
2

TABLE OF CONTENTS
3
BEFORE YOU BEGIN 4
DUCTING 4
External venting Requirements 4
Duct Run Calculation 5
ELECTRICAL 5
Electrical Supply 5
INSTALLATION 6
Applications 6
Connecting Electricity and Ducting 9
Re-Circulating Requirements 12
OPERATING PROCEDURES 13
General Advice 13
Functions 13
MAINTENANCE 16
Cleaning the Filter 16
Cleaning the Hood 16
Light Bulb Replacement 17
WARRANTY 20

4
BEFORE YOU BEGIN: It is advisable to test
run the range hood before installation.
BEFORE STARTING – please read this en-
tire document and ensure you are fully
conversant with the require-ments and
limitations. These units weigh approxi-
mately 125lbs and therefore require a
minimum of two people to install.
BEFORE YOU BEGIN
The manufacturer declines all responsi-
bility in the event of failure to observe the
instructions given here for installation,
maintenance and suitable operation of
the product. The manufacturer further
declines all responsibility for injury due
to negligence and the warranty of the
unit automatically expires due to impro-
per maintenance and/or installation.
Always fasten connections with sheet metal
screws and tape all joints with certied Sil-
ver Tape or Duct Tape. Do not use screws
to fasten ductwork to the hood, only use
tape as the screws will stop the dampers
from opening and your hood will not work.
This hood re-quires a 6” if it’s gas or gas
cook top 8” is recommended round duct
outlet. You can increase the duct size of
the duct run but never decrease it. Use
the shortest and most direct route possi-
ble. Always, wherever possible, reduce the
number of transitions and turns with as
few sharp angles as possible. Two stagge-
red 45 degree angles are better than one
90 degree. Make these turns as far away
from the motor exhaust as possible, with
as much space between each bend. Need
18” from the hood to the rst elbow.
DUCTING
(Not applicable if the range hood is used
in re-circulating mode).
WARNING: Do not vent this appliance
into any other ductwork, spaces between
walls, ceilings, attics, garages or any
other conned space.
External Venting Requirements.
When planning new ductwork, always
look for the most direct route to the ou-
tside. Venting can be done through the
roof or directly through the back outside
wall. (See Figure 1 and 2) Only use ri-
gid type metal ducting (plastic ducting is
generally not permitted by code). Flexi-
ble ducting could restrict airow by up
to 50%.
g. 1 g. 2

Duct Run Calculation.
The maximum duct run before eecting
the performance of the hood is 100’. Cal-
culate your duct run by measuring linear
feet and adding the elbows, transitions
and caps based on the table below.
5
Electrical Supply.
This appliance requires 120V/60Hz,
3amp electrical supply – ensure an ap-
propriately qualied person completes
the electrical hook-up. The connection
point for the electrical supply is at the top
of the unit, therefore the electrical supply
must be run down from the ceiling alon-
gside the ductwork.
All electrical and venting hook-ups must
be in place before commencing installa-
tion of the hood-fan.
ELECTRICAL
WARNING: All electrical work must be
performed by a qualied electrician.
Please ensure that the appropriate electri-
cal codes or prevailing local building co-
des and ordinances are adhered to.
Ensure that the electricity supply is di-
sconnected at source. Do not use an ex-
tension cord or adapter plug with this
appliance.
This appliance must be grounded. Con-
nect to a properly grounded branch
circuit, protected by a 15 amp circuit
breaker.
The ducting connection to the hood
must be in line with the central verti-
cal axis of the range hood 1” away from
the back wall on which the hood is to be
mounted.
Range hoods may interrupt the proper
ow of combustion gases from repla-
ces, gas furnaces and gas water heaters.
To minimize the risk of drawing these
lethal gases back into the home, please
follow the heating equipment manufac-
turers safety standards and guidelines
carefully.
Refer to NFPA and ASHRAE for additional
information.
Maximum Run
6” or 3 1/4 x 10” duct * 100 FT
Deduct
Each 90 elbow used 15FT
Each 45 elbow used 9FT
Each 6” or 3 1/4 x 10” duct
Transition used 1FT
Each 3” 1/4 x 10” to 6”
Transition used 5FT
Side Wall with damper 30FT
Roof Cap 30FT
* Gas range or gas cook top shuld be 8”.

6
SU900 - SUT900 – SUE900 20”
10” 3/8 X 19” 19/32
SU900 - SUT900 – SUE900 27”
10” 3/8 X 26” 11/16
SU901 32” 13/32 X 16” 3/16
SU902 10” 25/64 X 26” ½
SU903 27” 9/16 9” 15/16 X 25” 9/16
SU903 35” 7/16 9” 15/16 X 33” 7/16
SU908 12” 5/8 X 26” 2/2
SU906 33” 15/32 10” 14/32 X 32” 14/16
SU906 20” 15/32 10” 14/32 X 18” 19/32
SU913 20” 15/32 10” 3/8 X 19” 49/64
SU913 30” 23/32 10” 3/8 X 30” 5/64
If Sch31A or a Pro Liner are being used,
they can be held up under the cabinet
and used as a template.
If Sch31A or a Pro Liner are to be used
for under cabinet application, they
should be installed now.
INSTALLATION
The minimum distance between sup-
porting surface for the cooking ves-
sels on the hob, and the lowest part of
the range hood shall be at least 30”.
Applications
The SU900 - SUT900 – SUE900 can
either be installed inside a wall cabinet
(provided the inside depth is greater
than 11”) or used in a custom designed
wooden hood. Where installed directly
into a wall cabinet, there are two options:
Directly into the cabinet without any
form of hood. Directly into the cabinet
together with Sch31A where the Sch31A
acts as a liner hood and is attached to ei-
ther the underside of the cabinet or into
the sides of the cabinets alongside.
The SU901 can either be installed inside
a wall cabinet or used in a custom de-
signed wooden hood. Where installed
directly into a wall cabinet, there are two
options:
Directly into the cabinet or directly into
the cabinet together with the adjustable
Pro liners where the adjustable Pro li-
ners act as a cabinet protection against
the heat. The depth of the adjustable pro
liners can vary from 23.5” to 25.9”).
The SU902, SU903, SU906, SU913 can
either be installed inside a wall cabinet
or used in a custom designed wooden
hood.
Depending on which model is used, pre-
pare a cut-out in the underside of the
wooden hood to allow the powerpack to
t up into the hood using the following
dimensions:

Installing a SCH31A with SU900 -
SUT900 – SUE900. Hold the Sch31A un-
der the cabinet and Screw it to the 4 hole
locations. Make sure it lines up with the
cut out in your cabinet. The power pack
has pressure springs (to be adjusted) on
the front and back that will “hook” onto
the top surface of the underside of the
hood when it is pushed up into the hole
that has been cut out (refer to gure 3).
Installing SU900 - SUT900 – SUE900
without a SCH31A. The power pack has
pressure springs (to be adjusted) on the
front and back that will “hook” onto the
top surface of the underside of the hood
when it is pushed up into the hole that
has been cut out (refer to gure 3).
g. 3
7

There are four holes on the inside of the
SUT900 to x the unit into the edge of
the base of the wooden hood (refer to
gure 4).
Install the front part of the liner adjusting
it to the depth of the cabinet. (refer to -
gure 6).
g. 4
Installing a Adjustable Pro Liner with
SU901. Once the cut out has been done
install the Adjustable Pro Liner and make
sure it lines up with the cut out in your
cabinet. Screw it to the 4 hole locations
(refer to gure 5).
g. 5
lunedì 16 aprile 2007
SPESSORE:
MATERIALE:
RAGGIO PIEGA
Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con
Descrizione:
n° disegno:
nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.
Disegnato da: Data creazione:
lunedì 16 aprile 2007
SPESSORE:
MATERIALE:
RAGGIO PIEGA
Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con
nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.
Disegnato da:
Descrizione:
n° disegno:
Data creazione:
g. 6
Screw it to the 3 hole locations.
Attention: be sure the cabinet has a mi-
nimum thickness of 0.75” on the 4 sides.
lunedì 16 aprile 2007
SPESSORE:
MATERIALE:
RAGGIO PIEGA
Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con
nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.
Disegnato da:
Descrizione:
n° disegno:
Data creazione:
8

The power pack has pressure springs (to
be adjusted) on the front and back that
will “hook” onto the top surface of the
underside of the hood when it is pushed
up into the hole that has been cut out
(refer to gure 3).
Installing SU902. The power pack has
pressure springs (to be adjusted) on the
front and back that will “hook” onto the
top surface of the underside of the hood
when it is pushed up into the hole that
has been cut out (refer to gure 3).
Installing SU903. The power pack has
pressure springs (to be adjusted) on the
front and back that will “hook” onto the
top surface of the underside of the hood
when it is pushed up into the hole that
has been cut out (refer to gure 7-8).
g. 10
g. 7-8
Insert and Fix the 4 clamping levers as
described in the pictures 9.
g. 9
Screw carefully in order to keep the pro-
duct straight.
INSTALLING SU908
There are four holes on the inside of the
SU908 to x the unit intothe edge of the
base of the wooden hood (refer to gure 4).
Connecting Electricity and Ducting.
Please refer to the Electrical Supply sec-
tion on page 2 for the required location
of the electrical supply.
CAUTION: Make sure the power is tur-
ned o at source. Make electrical con-
nections (refer to Figure 10). Ensure that
the plastic aps at the exhaust outlet for
the fan move freely and have not become
jammed or stuck.
9

10
INSTALLATION SU906
Before installing the appliance, make
sure that none of the parts is damaged
in any way. In case of damaged parts,
contact your retailer and do not proceed
with installation.
Read all of the following instructions
with care before installing the appliance.
The LED bar of the range hood are sup-
plied in the packaging, and you need to
assemble them at the end of the instal-
lation.
- Before installing the appliance, remuve
the metal grase lter and the oil collec-
tor. Thes lter could be removed by pu-
shing the handles towards the back side
of the cooker hood and turning it down-
wards to unfasten it from its slot.
To remuve the oil collector, loosen the
two screws as indicated.
To install the appliance please respect
the follow instructions.
The appliance must be install by com-
petent authorities. In order to do not
damage the electronic parts of the ap-
pliance please do not use added screws.
Essential precautions to respect before
installing the appliance are the following:
- Prepare the power supply.
- Prepare a hole for the exhaust of the
air both in the ltering and in the
exhau sting version.
- Do not use screws to x the outlet
pipe to the cooker hoods.
- Avoid abrupt direction changes.
To have made a cut-out on the bottom
of the cabinet which is suitable to hold
the appliance in position.
SU906 20” 15/32 10” 3/8 X 18” 19/32
SU906 33” 15/32 10” 3/8 X 32” 14/16
Right now, after drilling the kitchen ca-
binet please follow carefully the instruc-
tions above, calibrate the xing spring
depending on the depth of cabinet.

At this point, insert the range hood in-
side the kitchen cabinet until the xed
springs will be hooked into.
Fix the range hood to the cabinet, in the
front and rear sides, using by the screws
equipped.
To x the hood on the rear side apply the
screws on the holes of oil container as
on pics indicated and fasten the screws.
Insert the LED bar on the appropriate
hole until it will be hooked into.
When the screws have been fastened,
take the LED bar and connect the two pin
connector.
At this point take the oil container and
hook it on the appropriate hole of the
hood. Please be careful not to scratch
and damage the product.
Fix the oil container xing the pommels
of range hood.
11

At the end, place the grease lters that
were removed before.
12
Rear vented version
All the models with one motor can be
rear vented; if the customer wants to use
this option, it is necessary to remove the
18 screws from the motor group sup-
port. Then take the metal support with
motor included out. Turn the motor to
have the air outlet on the rear side and
x the scews previously removed.
Connect the appropriate length of duc-
ting to the fan exhaust point and join up
with the ducting to the exterior.
Do not x the ducting to the range
hood exhaust outlet with screws-use
duct tape. Use duct tape on all joints.
Re-Circulating Requirements.
If the unit is to be used in the recircula-
ting mode, t the carbon lters after the
installation is complete (refer to Figure
11).
g. 11
The carbon lter ts in behind the alu-
minium grease lter. Ensure that the
plastic tabs on the carbon lter are fa-
cing outwards otherwise it will be di-
cult to remove it later for replacement.
A short length of ductwork must be
connected from the exhaust outlet on
the fan to wherever the air is to be
exhausted.
Allow sucient space to connect the
ductwork to the top of the exhaust out-
let on the fan housing. Do not x the
ducting to the range hood exhaust out-
let with screws, use duct tape. Duct tape
should be used on all joints.

FUNCTION
SU900–SU901–SU902–SU903-SU908-
SU906-SU913 (Fig. 12).
A: Light ON/OFF button
B: Blower Speed 1 (low) or OFF
C: Blower Speed 2 (medium)
D: Blower Speed 3 (high)
E: Blower Speed 4 (intensive)
F: 10 Minute Timer
OPERATING PROCEDURES
Read all the instructions before opera-
ting the appliance. Save these instruc-
tions for future reference.
General Advice.
Ensure that the grease lters are in place.
Without these components, operating
blowers could catch on to hair, ngers
and loose clothing. Keep fan, lters and
surfaces clean of grease and fat. Always
turn hood fan ON when cooking. NEVER
leave cooking unattended.
NEVER dispose cigarette ashes, ignitable
substances or any foreign objects into
blowers.
Cooking that generates ame is not re-
commended as this hood is equipped
with a thermal overload that will shut
down the motor if it senses excessive
heat. When frying, oil in the pan can ea-
sily overheat and ignite. Heat oil slowly
in an appropriately sized pot (covering
the entire burner) to reduce the risk of
boiling over and burning.
In the event of a range top grease re,
observe the following:
Switch OFF the range hood. Turn o
the cook top then smother ames with
a close tting lid, cookie sheet or other
metal tray. If the ames do not go out
immediately.
EVACUATE AND CALL THE FIRE DEPART-
MENT.
Never pick up a aming pan – you may
be burned. DO NOT USE WATER inclu-
ding wet dishcloths or towels, as a vio-
lent steam explosion may occur.
g. 12
SUE900 (Fig. 13)
A: Light ON/OFF button
B: Blower Speed 1 (low) or OFF
C: Blower Speed 2 (medium)
D: Blower Speed 3 (high)
E: Hood in operation light
g. 13
13

RC001
RADIO CONTROL
Radio control used for the remote operation
of ducted cooker hoods.
TECHNICAL DATA
- Alkaline battery powered: 12 V mod. 23 A
- Operating frequency: 433.92 Mhz
- Combinations: 32.768
- Max. consumption: 25 mA
- Operating temperature: -20 ÷ + 55 °C
- Dimensions: 120 x 45 x 15 mm.
OPERATING DESCRIPTION
The transmitter is equipped with 5 buttons
for cooker hood management, as specied
below:
: Light ON/OFF command.
: Motor ON (speed level 1) / OFF command.
: Reduce speed.
: Increase speed.
: 10-minute timer.
INITIAL OPERATING CONDITION
The manufacturer supplies the radio control
unit ready to be used with codes preset in the
Factory
OPERATION MODE
Standard conguration:
Standard conguration requires all “cooker
hoods – radio control - system” to be provi-
ded with the same transmission code. In the
event two cooker hoods – radio control sy-
stem are installed in the same room or near-
by, each system may aect the operation of
the another. Therefore, the code of one radio
control system must be changed.
Generatiing a new transmiissiion code:
The radio control system is provided with
preset codes. Should new codes be required,
proceed as follows: Press simultaneously but-
tons:
for two seconds. When Leds light on, press
buttons:
(within 5 seconds). Leds ashing 3 times in-
dicate
the procedure is completed.
WARNING! This operation deletes perma-
nently the preset codes.
Learniing the new transmiissiion code:
Once the transmission code is changed in the
radio control unit, the electronic central unit
of the cooker hood must be made to set the
new code in the fol- lowing way:
Press the main power-o button of the hood
and then restore power to the electronic con-
trol unit. Within the next 15 seconds, press
the Liight Button to synchronise the cen-
tral unit with the code.
Reset of the Factory coniguratiion:
To restore the Factory conguration, follow
the pro- cedure described below: press si-
multaneously buttons:
for 2 seconds. When Leds light on, press but-
tons:
14

(within 5 seconds). Leds ashing 6 times indi-
cate the procedure is completed.
WARNING! This operation deletes perma-
nently the preset codes.
Emergency button:
In the event that the radio control does not
work, use the emergency button to switch
the appliance o. After any necessary repai-
rs have been performed, reset the emergency
button.
WARNIING
The battery should be replaced every year
to guarantee the optimal range of the tran-
smitter.
To replace the exhausted battery, take the
plastic lid o, remove the battery and re-
place it with a new one, observing the cor-
rect battery polarities.
Used batteries should be discarded in spe-
cial collection bins.
The below product:
RC001 Radiio Controll
complies with the specications set out in
the R&TTE Directive 99/5/EC.
WARNING
Any adjustments or modications which
have not been expressly approved by the
holder of the legal conformity certicate
may invalidate the user’s rights relating to
the operation of the device.
Rev. 0 26/08/14
The products are endowed with an electronic
device which allows the automatic switching
o after 4 hours working from the last ope-
ration.
15

Warning The battery should be repla-
ced every year to guarantee the optimal
range of the transmitter. To replace the
exhausted battery, take the plastic lid
o, remove the battery and replace it
with a new one, observing the cor-
rect battery polarities. Used batteries
should be discarded in special collec-
tion bins.
Cleaning the Hood.
Cleaning of the internal parts should be
done with a clean damp (not excessively
wet) cloth together with regular household
detergent. The external stainless steel ele-
ments should be cleaned with a good qua-
lity foaming stainless steel cleaner. Read
the manufacturers directions. Generally
they recommend that the foam be sprayed
onto a clean dry cloth and then applied to
the stainless steel. Allow the foam to react
on the surface for a few minutes and then
wipe with a clean dry cloth.
On the surfaces that are exposed directly
to heat from the cook-top, it is advisable
to clean these on a regular basis to avoid
the marks from becoming baked on.
Do not under any circumstances use an
abrasive type cleaner as this will scratch
and damage the stainless steel nish.
Glass components should be cleaned with
a product such as Windex.
MAINTENANCE
The hood-fan should provide many
years of trouble free service provided it
is maintained properly.
Cleaning the Filter.
Clean the grease lter either by careful-
ly hand washing, (so as not to dama-
ge the lter design) or, preferably in a
dishwasher. Depending on use, the l-
ters should be cleaned at least every two
weeks in a dishwasher.
If a carbon lter has been tted this
must be replaced at least every 6 mon-
ths as a minimum. Depending on coo-
king style and nature of cooking (greasy
foods, fry’s, curries etc) would probably
require more frequent replacement – if
odors start to manifest themselves when
cooking it is time to replace the carbon
lter . We suggest you retain a spare set.
These can be ordered from the supplier
of your range hood.
Filter requires washing indicator: after
30 hours of use, all the buttons will li-
ght up to remind you that the grease lter
should be cleaned. Follow the instruc-
tions for cleaning lters in this booklet.
Once the grease lters have been cleaned
and replaced, reset by pressing the timer
button (F). Do not rely solely on this indi-
cator. Generally, the grease lter should
be washed on a regular basis to avoid
grease lter res.
The blower should be turned on for ap-
proximately 5 minutes before cooking
in order to establish air currents upward
through the hood. Use the low speeds
for normal use and the higher speeds for
strong odors and fumes.
16

Light Bulb Replacement.
(if in doubt, call 877-474-8770)
Turn blower and lights o. Make sure the
lights are cool.
Do not remove the entire xture (socket)
as this is very dicult to reinstall.
Visually inspect the light xture and esta-
blish whether the unit has a smooth or
“toothed” metal ring.
If smooth remove the glass blocking
ring by prying out with a sharp, soft in-
strument such as a toothpick (refer to -
gure 15).
g. 15
Steel instruments will scratch the surface.
Be careful that the lens does not fall out.
If “toothed”, place the tip of your nger
between the lens and the ring. Making
your way around the ring, gently pull
outwards until a point is found where the
ring pulls o.
Replace the appropriate bulb. Check
parts brochure or specication sheets on
our website. Wipe both sides of the glass
whilst it is out.
FOR SU906 - SU913
Substitution of the LED bar:
Using an appropriate tool, remove the
LED bar from its seat (refer to Fig. ????),
disconnect it electronically using the ap-
propriate connector then substitute it
with a LED bar with same characteristics.
17

18

19

Three Year Limited Warranty
YOU MUST REGISTER THE PURCHASE OF YOUR PRODUCT ON LINE AT www.siriuscappe.
com/usa/warranty.htm TO CONVALIDATE YOUR WARRANTY.
YOU CAN FIND THE DATA OF YOUR HOODS ON A LABEL INSIDE THE HOOD. JUST REMOVE
THE GREASE FILTER TO READ IT.
WARRANTY SERVICE
To qualify for warranty service, you must notify Sirius After sale service at the email ad-
dress stated below or call toll free USA 1-877-474-8770 and provide the model number,
description of the fault or defect and original date of purchase. Sirius reserves the right
to request proof of original purchase. Sirius will at its sole option and discretion replace
products that arrive damaged through shipping, provided shipping damage is reported as
stated above WITHIN 5 BUSINESS DAYS OF RECEIPT of the shipped product or products.
ONE YEAR SERVICE REPAIR WARRANTY:
During the rst year from date of original purchase, Sirius will, at its option, repair or repla-
ce, without charge, any product or part which is found to be defective under normal use and
service.
THREE YEAR PARTS WARRANTY:
For three years from date of purchase, Sirius will provide free of charge, non-consumable repla-
cement parts which are found to be defective under normal use and service.
WHO IS COVERED:
Sirius warrants to the original consumer purchaser of its products that such products will be
free from defects in materials and workmanship for a period of three years from the original
date of purchase. There are no other warranties, express or implied, including, but not limited
to, implied warranties of merchantability or tness for a particular purpose or application.
WHAT IS NOT COVERED:
This warranty does not extend to lters, lamps, batteries, ducts and ductwork components. This
warranty does not cover normal maintenance and service or products or parts which have been
subject to misuse, negligence, accident, improper maintenance or repair, faulty installation or
installation contrary to recommended installation instructions. The warranty on glass screens
is limited to manufacturing defects only and expressly excludes cracks and breakages as a
result of faulty installation. Labor and associated costs associated directly with removal and re-
installation are expressly excluded.
The duration of any implied warranty is limited to the three year period as specied for the
express warranty. Some states and provinces do not allow limitation on how long an implied
warranty lasts, so the above limitation may not apply to you.
Sirius S.P.A.
Zona industriale Berbentina 6/A
60041 SASSOFERRATO (AN)
ITALY
Sirius after sale service
Telephone (toll free): 1-877-474-8770
Email: [e-mail]
Register Online! www.siriuscappe.com/usa/warranty.htm
90009100150 - GM 04/16