Sirius Satellite Radio SL920 FRESCO Series User manual

1
SL920 FRESCO series
UNDERMOUNT RANGEHOOD
INSTALLATION INSTRUCTIONS
Congratulations on your purchase!
Thank you for choosing a Sirius product.
SL920 FRESCO 850 EAN #9351116002022
SL920 FRESCO 1200 EAN #9351116002039
SL920 FRESCO 1500 EAN #9351116002046
www.siriusbrand.com

2
The symbol on the product or on its packaging indicates that this product
may not be treated as house-hold waste. Instead it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about
recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the
product. This appliance is marked according to the European directive
2002/96/EC on waste electrical and electronic equipment (WEEE).
BEFORE YOU INSTALL – please read
Sirius warranty covers only Sirius product. If you choose to install a non-Sirius branded accessory
such as flexible ducting, Sirius will only warrant the hood and motor. If installation is found to be
the cause of failure or issue then charges will apply for service and parts.
Flexible ducting is not permitted under any circumstances. Flexible ducting has been found to
increase noise levels, increase vibration and reduce airflow.
Sirius Semi-rigid or solid ducting can be used in lieu.
There is a range available to suit any application.
Ducting available at www.siriusbrand.com
6 Year Warranty when Sirius Ducting is used. Full replacement warranty on parts and labour.
See website for terms & conditions.
A reduction in the duct diameter from stated ducting size will void warranty.
If you are in doubt about the ducting, please contact Sirius on 1300 762 219 prior to installation
CAUTION
WARNING
The appliance must be installed and
connected to the power supply only by a
qualified technician.
• There shall be adequate ventilation of the room when the range hood is used at the same time as
appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the
room)
• The details concerning the method and frequency of cleaning
• There is a fire risk if cleaning is not carried out in accordance with the instructions;
• Do not flambé under the range hood;
• CAUTION: Accessible parts may become hot when used with cooking appliances.

3
For 1500mm versions, a comprehensive list of
300mm components is available at
www.siriusbrand.com or contact nearest retailer.
Min. 1200mm - Max. 1600mm from the barbecue
grill surface for alfresco installations.
Min. 600mm - Max. 900mm for induction cooktops.
Min. 650mm - Max. 900mm gas cooktops.
If the rangehood is positioned above the max height
recommended, warranty may be compromised
as performance of the rangehood will be affected.
Measurement is taken from the top of the trivets to
the underside of the hood. (Fig. 1)
• The air being drawn can’t be conveyed through
or into a duct used to let out fumes from
appliances fed by energy other than electric
power (eg. centralized heating, radiators, water
heaters, etc.).
• Attention: remove any possible PVC film from the
stainless steel, including the filters.
• To externally vent, please comply with the
pertaining rules given by competent authorities.
• Provide the room with an adequate ventilation
when a rangehood and appliances fed by energy
other than electric power (gas, oil, or coal stoves,
etc.) are used simultaneously. The rangehood,
when evacuating the air, could generate a
negative pressure in the room which can’t exceed
the limit of 0.04 mbar, in order to avoid the
suck of exhausts deriving from the heat source.
Therefore the room should be provided with air
intakes to allow a constant flow of fresh air.
If the rating label in the rangehood shows the symbol
, the appliance is built in class II° and it does not
need any earth connection.
If the rating label in the rangehood does not show
the symbol , the appliance is built in class I° and it
needs the earth connection.
When performing the electrical connections on the
appliance, please make sure that the current-tap
is provided with earth connection and that voltage
values correspond to those indicated on the label
placed inside the appliance itself.
When ducting rangehood, options are as follows:
Roof vent - EASYROOF 200T/M
(for 850 & 1200 versions) *Kit includes roof flashing
Download installation guide
Eave vent - EASYEAVE 200 (for 850 & 1200 versions)
Download installation guide
Wall vent - EASYWALL 200 (for 850 & 1200 versions)
Download installation guide
Before carrying out any cleaning or maintaining
operations, the appliance needs to be switched off.
If the appliance is not provided with a non-separable
flexible cable and plug, or with another device
ensuring omnipolar disconnections from the grid,
with an opening distance between the contacts of at
least 3mm, then such disconnecting devices must be
supplied within the fixed installation.
If the fixed appliance is endowed with a supply cord
and a plug, the appliance has to be put in a place
where the plug can be reached easily.
The use of materials which can burst into flames
should be avoided in close proximity of the appliance.
When frying, please pay particular attention to fire
risk due to oil grease. Being highly flammable, fried
oil is especially dangerous. Do not use uncovered
electric grills. In order to avoid possible fire risk, all
instructions for grease-filter cleaning and for removing
eventual grease deposits should be strictly followed.
WARNING
1200mm - 1600mm (alfresco)
600 - 900mm (induction)
650 - 900mm (gas)
1200mm - 1600mm (alfresco)
600 - 900mm (induction)
650 - 900mm (gas)
(Fig. 1)
(Fig. 2a)
(Fig. 2b)
(Fig. 2c)
SIDE VIEW FRONT VIEW
Dome
featured on
200mm kit
only

4
To install the appliance please respect the follow
instructions:
• The appliance must be installed by qualified
technicians, or where possible use a Sirius
recommended installer. See siriusbrand.com. In
order to avoid damage to the electronic parts
of the appliance, please do not use additional
screws.
• Essential precautions to respect before installing
the appliance are the following:
To have made a cutout on the bottom of the
cabinet which is suitable to hold the appliance in
position (Fig. 4):
SL920 series INSTALLATION
Before installing the appliance, make sure that
none of the parts are damaged in any way. In
case of damaged parts, contact your retailer
and do not proceed with installation. Read all
of the following instructions with care before
installing the appliance.
• Use ducting within the min/max specifications
• Limit the number of ducting bends.
• Do not make any changes in ducting diameter
(recommended constant diameter:
Ø 200mm (850/1200 models), Ø 300mm
(1500mm models) or equal surface area).
Before installing the appliance - in order not to
damage the appliance itself - the metal grease filter
should be removed. These filters could be removed
by pushing the handles towards the back side of the
rangehood and pulling it downwards to unfasten it
from its slot. (Fig. 3).
NOTE
(Fig. 3)
(Fig. 4)
(d)
(w)
1. Prepare the power supply - 240 volts.
2. Prepare a hole for the exhaust - 210mm for for
twin motor versions and 310mm for triple motor
versions.
• Do not use screws to fix the ducting to the
rangehoods as they will prevent the movement of
non-return valves.
• Limit the number of elbows in the ducting, since
each elbow reduces the duct efficiency by 1
metre. (i.e. if you use two 90° elbows, the length
of ducting must not exceed 5 metres.)
• Avoid abrupt direction changes.
• Use 200mm constant diameter ducting for the
whole length for the twin motor, 300mm ducting
for the triple motor model.
• The use of Sirius ducting will increase the
warranty of the unit to 6 years.
WARNING: Failure to install the screws or fixing
device in accordance with these instructions
may result in electrical hazards.
SL920 FRESCO 850: (w) 821 x (d) 505mm
SL920 FRESCO 1200: (w) 1165 x (d) 505mm
SL920 FRESCO 1500: (w) 1470 x (w) 505mm

5
CAUTION
WARNING
The rangehood is quite heavy, so two people
will be needed for installation.
1. To install the appliance, adjust the position of the
adjustable side-springs using the supplied screws
(Fig. 5), according to the thickness of the board,
in which the appliance will be fixed.
2. Insert the rangehood into the cutout in the
cabinet until the stop click of the side-springs is
heard and the rangehood is supported.
3. Unscrew by 180°the horizontal screws as shown
in Fig. 5. During this action it is necessary to
support the hood with your hand (Fig. 5a).
4. Tighten the vertical screws to lift the height of the
hood upwards for a flush finish.
5. Repeat this operation for all four screws (Fig. 6).
6. If it is necessary, its possible to put other screws
along the front or rear of the product as shown in
Fig. 7. This is not absolutely necessary if the
cutout is the correct depth.
7. Insert the grease filter.
Before connecting any ducting to the motor,
make sure the non-return valves - which are on
the air outlet of the motor - can swing open.
External venting
• Connect the ducting to the outlet collar of the
rangehood and secure with a clamp.
• Run the ducting to your external vent/cowl,
making sure the appropriate ducting is used for
the entire run.
(Fig. 5)
Spring-loaded
clips
(Fig. 6)
(Fig. 5a)
(Fig. 7)
SL920 FRESCO series (Fig. 8)
A: Light switch on/off
B: Motor switch on speed 1/off - (low/simmer)
C: Motor switch on speed 2 - (general cooking)
D: Motor switch on speed 3 - (high power)
E: Motor switch on speed 4 - (booster)
F: 10 minute shut-off timer
OPERATION
(Fig. 8)
• NB: light is easier to remove from centre of
LED globe. Use a small, flathead screwdriver
(pictured), pallette knife or blunt butter knife.

6
• Accurate maintenance guarantees good
functioning and long-lasting performance.
• Particular care is due to the grease filter panel. It
can be removed by pushing its handle toward the
back side of the rangehood and pulling the filter
downwards so to unfasten it from its slot (Fig. 3).
To insert the filter just perform the opposite
operation.
• After 30 hours of use, the timer button control
panel will flash, signaling the filters are due for
cleaning. Press the timer button to reset.
The grease filter needs cleaning by regular
handwashing or in dishwashers every two
months at least, depending on its use.
Filters may require cleaning sooner if
frequent heavy frying is done.
Induction cooking with frequent boiling
will create more condensation. Filters may
require to be dried more frequently.
• To clean the appliance itself, water and detergent
are recommended, while abrasive products
should be avoided. For steel appliances
specialized detergents are recommended (please
follow the instructions indicated on the product
itself to obtain the desired results).
MAINTENANCE
WARNING
NOTE
To remove the rangehood from the cabinet
(Fig. 11), remove the fixing screws (Fig. 6) using
a screwdriver, and remove the grease filters.
WARNING: This will require a minimum of 2
people.
If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order to
avaoid a hazard.
(Fig.9)
To clean the grease channel, remove the baffle filter
and unscrew the screws holding the channel in place.

7
6 channel control for rangehood remote.
• When the rangehood is first turned on, hold the
lighting button for 5 seconds.
RC001 - RADIO CONTROL
Radio control used for the remote operation of
rangehoods.
TECHNICAL DATA
• Alkaline battery powered: 12 V mod. 23 A
• Operating frequency: 433.92 Mhz
• Combinations: 32.768
• Max. consumption: 25 mA
• Operating temperature: -20 ÷ + 55 °C
• Dimensions: 120 x 45 x 15 mm.
OPERATING DESCRIPTION
The transmitter is equipped with 5 buttons for cooker
hood management, as specified below:
: Light ON/OFF command.
: Motor ON (speed level 1) / OFF command.
: Reduce speed.
: Increase speed.
: 10-minute timer.
INITIAL OPERATING CONDITION
The manufacturer supplies the radio control unit
ready to be used with codes preset in the factory.
REMOTE CONTROL

8
ARISIT PTY LIMITED (Australia)
ABN 23 091 515 294
40-50 Mark Anthony Drive
Dandenong South VIC 3175
P: Sales & Service: 1300 762 219
F: Sales & Service: [phone]
E: [email protected]
ARISIT PTY LIMITED (New Zealand)
1A Howe Street Newton, Auckland 1145
PO Box 68-140 Newton, Auckland 1145
P: [phone] - Fax: [phone]
E: [email protected]
Sirius Hoods and ducting products are only available
from our select group of Sirius Professional Stockists
nationwide. For the latest list of Sirius Stockists
near you, please refer to www.siriusbrand.com
All efforts have been made to ensure that the
information provided in this brochure is correct at
the time of printing. Due to continuous product
improvement and ongoing development, Sirius
reserves the right to make changes to the
products and technical data without prior notice.
Some products appearing in this brochure may
be for illustrative purposes only. Diagrams are
indicative measures only. Prior to commencing
cabinetry cutouts the operating/installation
instructions accompanying the product must
be referred to at www.siriusbrand.com
www.arisit.com
www.arisitwarranties.com.au
www.siriusbrand.com
when Sirius ducting is used.
Full replacement warranty on parts and labour. Check website for T&Cs.
Year
Warranty
WIRING DIAGRAM: SL920 FRESCO