Sirona inEos Blue User manual

MTKOMNN
páêçå~=aÉåí~ä=`^aL`^j=póëíÉã
áåbçë=_äìÉ
kÉï=~ë=çÑW=
båÖäáëÜ=ErpF
léÉê~íáåÖ=fåëíêìÅíáçåë
Operatin g Instruct ions

63 33 632 D3446
2D3446.201.02.03.23 07.2011
Sirona Dental Systems GmbH
Operating Instructions Sirona Dental CAD/CAM System
Table of contents
1Dear Customer, ........................................................................................................ 5
2General information.................................................................................................. 6
2.1 Structure of the document............................................................................. 6
2.1.1 Identification of danger levels............................................................. 6
2.1.2 Formats and symbols used................................................................ 7
2.2 Legend .......................................................................................................... 7
2.3 Warranty........................................................................................................ 7
3Safety ....................................................................................................................... 8
3.1 Basic safety information ................................................................................ 8
3.1.1 Prerequisites ...................................................................................... 8
3.1.2 Connecting the unit ............................................................................ 8
3.1.2.1Connection to the CEREC 3 acquisition unit...................................... 8
3.1.2.2Connection to the CEREC AC acquisition unit................................... 9
3.1.3 Connection of external equipment ..................................................... 10
3.1.4 Maintenance and repair ..................................................................... 10
3.1.5 Changes to the product...................................................................... 10
3.1.6 Accessories........................................................................................ 10
3.1.7 In case of damage.............................................................................. 10
3.2 Intended use ................................................................................................. 11
3.3 Further use of Sirona Dental CAD/CAM System .......................................... 11
3.4 Certification ................................................................................................... 12
4Technical description................................................................................................ 13
4.1 Design and function ...................................................................................... 13
4.2 System components...................................................................................... 13
4.2.1 Components of the inEos Blue........................................................... 14
4.2.2 Accessories (included in the scope of supply) ................................... 15
4.2.3 Calibration parts (included in scope of supply) .................................. 16
4.2.3.13D acquisition system ........................................................................ 16
4.2.3.2XYZ axis alignment ............................................................................ 16
4.3 Technical data............................................................................................... 17
4.4 System requirements .................................................................................... 17
5Transport to the installation site ............................................................................... 18

63 33 632 D3446
D3446.201.02.03.23 07.2011 3
Sirona Dental Systems GmbH
Operating Instructions Sirona Dental CAD/CAM System
5.1 Transport and unpacking.............................................................................. 18
5.2 Installation site.............................................................................................. 18
6Initial installation of the software.............................................................................. 19
6.1 Installation of the user software and initial start-up ...................................... 19
6.2 Connecting the unit to the PC ...................................................................... 19
6.3 Switching the unit on and starting the software............................................ 20
6.4 Selecting the 3D acquisition system............................................................. 20
6.5 Adding inEos Blue to the device configuration ............................................. 21
7Connecting the unit.................................................................................................. 22
7.1 Connecting the inEos Blue to the PC........................................................... 22
7.2 Connecting the inEos Blue to the power supply........................................... 22
7.3 Connecting the rotation mouse .................................................................... 23
7.4 Connecting the foot switch ........................................................................... 23
8Controls and displays .............................................................................................. 24
8.1 Controls on the inEos Blue........................................................................... 24
8.2 Ready LED ................................................................................................... 25
9Switching the system on.......................................................................................... 26
10 Calibration ............................................................................................................... 27
10.1 General information on calibration ............................................................... 27
10.2 Calibrating the 3D camera system ............................................................... 27
10.3 Calibrating the XYZ axis alignment .............................................................. 28
11 Performing 3D acquisition ....................................................................................... 32
11.1 General......................................................................................................... 32
11.1.1 Scan models ..................................................................................... 32
11.1.2 Focusing the image........................................................................... 33
11.1.3 Overlap area during acquisition ........................................................ 33
11.1.4 Deleting images ................................................................................ 33
11.1.5 Operating the foot switch .................................................................. 34
11.2 Raster scans ................................................................................................ 34
11.2.1 Preparing the model.......................................................................... 34
11.2.2 Taking a scan.................................................................................... 34

63 33 632 D3446
4D3446.201.02.03.23 07.2011
Sirona Dental Systems GmbH
Operating Instructions Sirona Dental CAD/CAM System
11.3 Free scans .................................................................................................... 35
11.3.1 Preparing the model........................................................................... 36
11.3.2 Taking a scan..................................................................................... 36
11.3.3 Performing detail scans...................................................................... 37
11.4 Rotational scans............................................................................................ 38
11.4.1 Preparing the model........................................................................... 38
11.4.2 Taking a scan..................................................................................... 38
11.5 Acquiring impressions ................................................................................... 38
11.6 Examples ...................................................................................................... 40
11.6.1 Scan of a 3-unit bridge....................................................................... 40
11.6.1.1Acquiring a preparation .................................................................... 40
11.6.1.2Rotational scans............................................................................... 42
11.6.1.3Acquiring an antagonist.................................................................... 43
11.6.1.4Bite registration ................................................................................ 44
11.6.1.5Buccal scan...................................................................................... 44
11.6.1.6Terminating acquisition .................................................................... 45
11.6.2 Acquisition of a crown cap ................................................................. 45
11.6.3 Exposure of an inlay........................................................................... 46
11.6.3.1Acquiring a preparation .................................................................... 46
11.6.3.2Considering the antagonist .............................................................. 49
11.6.3.3Terminating acquisition .................................................................... 49
12 Cleaning and care .................................................................................................... 50
12.1 Care of the 3D camera system ..................................................................... 50
12.2 Cleaning the outer surface ............................................................................ 50
12.3 Protection against medicaments ................................................................... 50

63 33 632 D3446
D3446.201.02.03.23 07.2011 5
Sirona Dental Systems GmbH 1Dear Customer,
Operating Instructions Sirona Dental CAD/CAM System
1Dear Customer,
Dear Customer,
Thank you for purchasing your inEos Blue® from Sirona.
Improper use and handling can create hazards and cause damage.
Please read and follow these operating instructions carefully and always
keep them within easy reach.
To prevent personal injury or material damage, it is important to observe
all safety information.
To safeguard your warranty claims, please complete the attached
Installation Report / Warranty Passport when the system is handed over
and send it to the indicated fax number.
Your
inEos Blue Team

63 33 632 D3446
6D3446.201.02.03.23 07.2011
2 General information Sirona Dental Systems GmbH
2.1 Structure of the document Operating Instructions Sirona Dental CAD/CAM System
2General information
General information
Please read this document completely and follow the instructions exactly.
You should always keep it within reach.
Original language of the present document: German.
2.1 Structure of the document
Structur e of the d ocument
2.1.1 Identification of danger levels
Identificatio n of danger l evels
To prevent personal injury and material damage, please observe the
warning and safety information provided in this document. Such
information is highlighted as follows:
Tip: Information on making work easier.
CAUTION
Be sure to observe all warnings!
Please observe the warning and safety information provided to prevent
personal injury and material damage. Any such information is
highlighted by a signal word, i.e. DANGER, WARNING, CAUTION or
NOTICE.
DANGER
An imminent danger that could result in serious bodily injury or death.
WARNING
A possibly dangerous situation that could result in serious bodily injury
or death.
CAUTION
A possibly dangerous situation that could result in slight bodily injury.
NOTICE
A possibly harmful situation which could lead to damage of the product
or an object in its environment.
IMPORTANT
Application instructions and other important information.

63 33 632 D3446
D3446.201.02.03.23 07.2011 7
Sirona Dental Systems GmbH 2General information
Operating Instructions Sirona Dental CAD/CAM System
2.1.2 Formats and symbols used
Formats and symbols used
The symbols and character formats used in the present manual have the
following meaning:
2.2 Legend
Legend
Year of manufacture
2.3 Warranty
Warranty
To safeguard your warranty claims, please complete the attached
Installation Report / Warranty Passport when the unit is handed over.
Then fax it to the specified fax no.
✔Prerequisite
1. First action step
2. Second action step
or
➢ Alternative action
ªResult
Requests you to do something.
See "Formats and symbols
used [ → 7]“
Identifies a reference to another
text passage and specifies its page
number.
●List Identifies a list.
"Command/menu item" Identifies commands, menu items
or quotations.
20XX

63 33 632 D3446
8D3446.201.02.03.23 07.2011
3 Safety Sirona Dental Systems GmbH
3.1 Basic safety information Operating Instructions Sirona Dental CAD/CAM System
3Safety
Safety
3.1 Basic safety information
Basic safety in formation
3.1.1 Prerequisites
Prerequisites
3.1.2 Connecting the unit
Connecti ng the un it
Description
Perform connection by following the directions given in the present
operating instructions.
3.1.2.1 Connection to the CEREC 3 acquisition unit
Connecti on to the CEREC 3 acquisiti on unit
Warning: inEos connected to CEREC 3 acquisition unit
NOTICE
Important information on the building installation
The building installation must be performed by a qualified expert in
compliance with the national regulations. DIN VDE 0100-710 applies in
Germany.
NOTICE
Restrictions regarding installation site
The system is not intended for operation in areas subject to explosion
hazards.
NOTICE
Do not damage the unit!
The unit can be damaged if opened improperly.
It is expressly prohibited to open the unit with tools!
WARNING
No acquisitions in the patient's mouth
As long as an inEos Blue is connected to a CEREC 3 acquisition unit,
no acquisitions may be made in the patient's mouth using the connected
CEREC 3D camera.

63 33 632 D3446
D3446.201.02.03.23 07.2011 9
Sirona Dental Systems GmbH 3Safety
Operating Instructions Sirona Dental CAD/CAM System
3.1.2.2 Connection to the CEREC AC acquisition unit
Connection to the CEREC AC acquisition unit
Patient environment
Within the patient environment (A), direct contact is only permissible with
devices or system parts that are approved for use in the patient
environment (A).
This applies to all possible patient positions (B) during the examination or
treatment.
inEos outside of patient environment
WARNING
No acquisitions in the patient's mouth within the patient environment
As long as an inEos Blue is connected to a CEREC AC acquisition unit,
no acquisitions may be made in the patient's mouth using the connected
CEREC Bluecam if the inEos Blue is located outside of the patient
environment.
1500mm
59”
1500mm
59”
1500mm
59”
1500mm
59”
1500mm
59”
1500mm
59”
1500mm
59” 1500mm
59”
1500mm
59”
1500mm
59”
1500mm
59”

63 33 632 D3446
10 D3446.201.02.03.23 07.2011
3 Safety Sirona Dental Systems GmbH
3.1 Basic safety information Operating Instructions Sirona Dental CAD/CAM System
3.1.3 Connection of external equipment
Connecti on of exte rnal equipment
If any equipment not approved by Sirona is connected, it must comply
with the applicable standards:
● EN 60 950 for information technology equipment, and
● EN 61 010-1 for laboratory equipment.
3.1.4 Maintenance and repair
Maintenance and repair
As manufacturers of dental instruments and laboratory equipment, we
can assume responsibility for the safety properties of the unit only if the
following points are observed:
● The Maintenance and repair of this unit may be performed only by
Sirona or by agencies authorized by Sirona.
● Components which have failed and influence the safety of the unit
must be replaced with original (OEM) spare parts.
Please request a certificate whenever you have such work performed. It
should include:
● The type and scope of work.
● Any changes made in the rated parameters or working range.
● Date, name of company and signature.
3.1.5 Changes to the product
Changes to th e product
Modifications to this unit which may affect the safety of the operator,
patients or third parties are prohibited by law!
3.1.6 Accessories
Accessories
In order to ensure product safety, this product may be operated only with
original Sirona accessories or third-party accessories expressly approved
by Sirona. The user assumes the risk of using non-approved accessories.
3.1.7 In case of damage
In case of da mage
In case of noticeable malfunctions or damage, stop using the instrument
immediately and notify your dental depot or the manufacturer.

63 33 632 D3446
D3446.201.02.03.23 07.2011 11
Sirona Dental Systems GmbH 3Safety
Operating Instructions Sirona Dental CAD/CAM System
3.2 Intended use
Intended use
Indications for u se
The Sirona Dental CAD/CAM System is intended for use in partially or
fully edentulous mandibles and maxillae in support of single or multiple-
unit cement retained restorations. The system consists of three major
parts: TiBase, inCoris mesostructure, and CAD/CAM software.
Specifically, the inCoris mesostructure and TiBase components make up
a two-piece abutment which is used in conjunction with endosseous
dental implants to restore the function and aesthetics in the oral cavity.
The inCoris mesostructure may also be used in conjunction with the
Camlog Titanium base CAD/CAM (types K2244.xxxx) (K083496) in the
Camlog Implant System. The CAD/CAM software is intended to design
and fabricate the inCoris mesostructure. The inCoris mesostructure and
TiBase two-piece abutment is compatible with the following implants
systems:
● Nobel Biocare Replace (K020646)
● Nobel Biocare Branemark (K022562)
● Friadent Xive (K013867)
● Biomet 3i Osseotite (K980549)
● Astra Tech Osseospeed (K091239)
● Zimmer Tapered Screw-Vent (K061410)
● Straumann SynOcta (K061176)
Note for use in the USA
Note for use in the USA
CAUTION: According to US Federal Law, this product may be sold only
to or by instruction of physicians, dentists, or licensed professionals.
3.3 Further use of Sirona Dental CAD/CAM System
Further use of Sirona Dental CAD/CAM System
The Sirona Dental CAD/CAM System is also an optical impression
system for computer assisted design and manufacturing (CAD/CAM)
according to 21 CFR 872.3661.The system records the topographical
characteristics of teeth, dental impressions, or stone models for use in the
computer-assisted design and manufacturing of dental restorative
prosthetic devices. Such devices are exempt from the premarket
notification procedures.

63 33 632 D3446
12 D3446.201.02.03.23 07.2011
3 Safety Sirona Dental Systems GmbH
3.4 Certification Operating Instructions Sirona Dental CAD/CAM System
3.4 Certification
Certificat ion
CE mark
This product bears the CE mark in accordance with the provisions of
directives 2006/95/EC (Low Voltage Directive) and 2004/108/EC (EMC
Directive).
Examples EN60950 + CAN/CSA
Examples of CE mark for connected products:
● EN 60950:1992 + A1:1993 + A2:1993 + A3:1995 + A4:1997 based on
IEC 60950
● CAN/CSA-C22.2 No.61010-1-04.
inLab+Eos GOST mark
GOST mark
CSA mark
CSA mark
VDE mark
VDE mark
CAUTION
CE mark for connected products
Further products which are connected to this unit must also bear the CE
mark. These products must be tested according to the applicable
standards.
CUS

63 33 632 D3446
D3446.201.02.03.23 07.2011 13
Sirona Dental Systems GmbH 4Technical description
Operating Instructions Sirona Dental CAD/CAM System
4Technical description
Technica l description
4.1 Design and function
Design and function
The inEos Blue is designed as a desktop unit and consists of several
components (see Chapter "System components" [ → 13]). It is powered
from the standard local power network via an external power supply unit.
The unit is connected to a PC via a USB port. The PC must fulfill the
minimum requirements (see Chapter on "System requirements" [ → 17]).
The PC serves both for controlling inEos Blue and for displaying the
captured images by means of the user software.
4.2 System components
System components
"inEos Blue" consists of a base plate and a vertical unit. In addition,
different accessories as well as the required calibration kits are included
in the scope of supply of the system.
A
B
C
D
AExternal power supply unit
BSupply board
CRotation mouse
D3D acquisition system

63 33 632 D3446
14 D3446.201.02.03.23 07.2011
4 Technical description Sirona Dental Systems GmbH
4.2 System components Operating Instructions Sirona Dental CAD/CAM System
4.2.1 Components of the inEos Blue
Components o f the inEos Blue
Vertical unit and front side of base plate
AVertical unit EBase plate
BRotary knobs for height
adjustment
FReady LED (blue)
CHeight adjustment unit
with 3D camera system
GShifting plate
DCone with glass
protection cover
HStart button
IRotation mouse

63 33 632 D3446
D3446.201.02.03.23 07.2011 15
Sirona Dental Systems GmbH 4Technical description
Operating Instructions Sirona Dental CAD/CAM System
Rear side of base plate
4.2.2 Accessories (included in the scope of supply)
Accessories (included in the scope of supply)
AMain switch
BSupply voltage input
CUSB port
DRotation mouse
AModel holder (with ball-and-socket joint)
BSliding block
CClamps
DModel pot 31 (3x)
EModel pot 52 (2x)
FPlate
E
D
F
A
B
C

63 33 632 D3446
16 D3446.201.02.03.23 07.2011
4 Technical description Sirona Dental Systems GmbH
4.2 System components Operating Instructions Sirona Dental CAD/CAM System
4.2.3 Calibration parts (included in scope of supply)
Calibratio n parts (include d in scop e of supp ly)
4.2.3.1 3D acquisition system
3D acqui sition system
Calibration part for calibrating the 3D acquisition system.
4.2.3.2 XYZ axis alignment
XYZ axis alignment
Calibration parts for calibrating the XYZ axis alignment
Foot control
ACalibration part
A
ACalibration plate
BSpacer
A B

63 33 632 D3446
D3446.201.02.03.23 07.2011 17
Sirona Dental Systems GmbH 4Technical description
Operating Instructions Sirona Dental CAD/CAM System
4.3 Technical data
Technica l data
4.4 System requirements
System requirements
An inLab PC 64bit is required to run this software. The hardware version
must be PC Hardware L or higher.
Model designation inEos Blue
Power connection via power supply unit:
INPUT: 100-240VAC / 47- 63Hz / 1.0 A max.
permissible line voltage fluctuations:
± 10% of nominal voltage
Overvoltage category II
OUTPUT: +12VDC / 2.08A / 25W max.
Power consumption 15 W
Ambient conditions For indoor use
Pollution degree 2
Temperature: 10°C – 35°C (50°F ~ 95°F)
Relative humidity: 30% – 75%
Barometric pressure: 700hPa – 1060hPa
Transport and
storage conditions
Temperature: -40°C – +70°C (-40°F ~ 158°F)
Relative humidity: 10% – 95%
Barometric pressure: 500hPa – 1060hPa
Protection class Class I device
Degree of protection against
ingress of water
Ordinary equipment (not protected)
Mode of operation Continuous operation with intermittent loading corresponding to the
laboratory mode of working.
Tabletop unit
Tests/approvals This device complies with the requirements of
EN 61 010-1: 2001

63 33 632 D3446
18 D3446.201.02.03.23 07.2011
5 Transport to the installation site Sirona Dental Systems GmbH
5.1 Transport and unpacking Operating Instructions Sirona Dental CAD/CAM System
5Transport to the installation site
Transport to the installat ion site
5.1 Transport and unpacking
Transport and unpacking
Transport and un packing
All Sirona products are carefully checked prior to shipment. Please
perform an incoming inspection immediately after delivery.
1. Check the delivery note to ensure that the consignment is complete.
2. Check whether the product shows any visible signs of damage.
If return shipment is required, please use the original packaging for
shipment.
5.2 Installation site
Installatio n site
The unit is designed for desktop use and requires a level footprint of
approx. 35 x 45 cm for installation.
Make sure that suitable operating conditions are given (see section on
“Technical data“ [ → 17]).
NOTICE
Damage during transport
If the product was damaged during transport, please contact your
carrying agent.
NOTICE
Install inEos Blue in a protected area
3D image acquisition may be adversely affected by bright light.
Set the inEos Blue up so that it is not located directly in the beam path
of an extreme light source and not exposed to direct sunlight.

63 33 632 D3446
D3446.201.02.03.23 07.2011 19
Sirona Dental Systems GmbH 6 Initial installation of the software
Operating Instructions Sirona Dental CAD/CAM System
6Initial installation of the software
Initial inst allation of the software
6.1 Installation of the user software and initial start-up
Installation of the user software and initial start-up
1. Start your PC.
2. Insert the DVD into the DVD drive of your PC.
ªThe installation wizard opens.
3. Click the
"next" button.
4. Read the license agreement.
5. Confirm your acceptance by clicking the
"Yes" button.
6. Click
"Standard Installation" .
ªThe standard installation is then executed.
7. Follow the instructions of the installation wizard to complete the
installation.
8. Restart the system.
ªThe software and drivers are installed.
6.2 Connecting the unit to the PC
Connecting the u nit to the PC
➢Connect the inEos Blue to the PC (see also section “Connecting the
unit“ [ → 22]).
NOTICE
Initial installation without inEos Blue
Perform the initial installation of the software without connecting inEos
Blue.
NOTICE
Installation does not start
The installation will start automatically. If it does not start, the CD
autorun feature is disabled on your PC. In this case start the
setup.exe file on the CD-ROM by double-clicking it.
NOTICE
User-defined installation
The user-defined installation option is recommended only for
experienced users.

63 33 632 D3446
20 D3446.201.02.03.23 07.2011
6 Initial installation of the software Sirona Dental Systems GmbH
6.3 Switching the unit on and starting the software Operating Instructions Sirona Dental CAD/CAM System
6.3 Switching the unit on and starting the software
Switching the unit on and starting the soft ware
Let unit dry off after sto rage
1. Switch the unit on at the main switch.
2. Start the software at the PC via the Windows start menu.
6.4 Selecting the 3D acquisition system
Selecting the 3D acquisition system
1. Click "Settings" / "Configuration" / "Acquisition system" in the user
software.
ªThe menu for selection of the 3D acquisition system opens.
2. Select
"inEos" .
3. Click the
"OK" button.
NOTICE
Do not put the unit into operation at low temperatures!
If you move the unit to the operating site from a cold environment,
condensation may form and result in a short circuit.
✔Install the unit at room temperature.
➢Wait until the unit has reached room temperature and is absolutely
dry.
ªThe unit is dry and can be put into operation.