Sister Bay HYANNIS MHYA-G-S-R User manual

Seat Back
Assembly
I
Under Arm
Brace
H
Right Leg
Assembly
Seat Bottom
Assembly
Glider Right
Base Assembly
J
Glider Left Base
Assembly
P
Glider Base Middle Brace
Front & Back
K
MN
(4)
2.75
2.50
B
(10)
A(4)
3.50
C
(4)
F1 (4)
(4)
D1
E2
(8)
D2
(4)
E1
F2 (4)
Hardware and Parts
2.50
(8)
G
1.50
G1 (16)
Assembly Instructions
Arm
L
Left Leg
Assembly
Q
Do not use
any hand drill
on this product
WRENCH
( not included )
ALLEN WRENCH
( included )
You will also need a phillips-head screwdriver
( not included )
Item No: MHYA-G-S-R
HYANNIS SINGLE GLIDER
Item No: MYAR-G-S-R
YARMOUTH SINGLE GLIDER

Right side
Front Leg (FR)
(identification marks
facing up)
J
Under Arm
brace
FRONT
Right side
Rear Leg (RR)
(identification
marks
facing up)
J
1a - Attach part ( K ) under arm brace to part ( J ) front right side ( FR ) & Rear right side ( RR ) legs using 4 of screws.
( G ) 2 for each leg. Tighten screws using a phillips-head screwdriver. Be sure to lay the legs and arm brace on
a flat clean surface to assemble. Line up the front right leg ( FR ) with the front of the arm brace ( 2 screws ),
line up the rear right side leg ( RR ) with the back of the arm brace (1 screw). Make sure the identification marks
FR & RR are facing upward. Follow the same instructions for left side legs ( Q ), the identification marks FL & RL
should be facing down. Leg and arm brace assembly should form an "A" frame if done correctly.
1b - To Attach part ( J ) , Right leg Assembly to part ( L ) arm, lay arm face down on a flat clean surface, place ( J )
right side leg assembly over the arm using ( 6 ) of screw ( G1 ) tighten screws using a phillips-head screwdriver.
Follow the same instructions for left side legs ( Q ).
FR
RR
FR
RR
K
Right side
Rear Leg (RR)
(identification marks
facing up)
J
Right side
Front Leg (FR)
(identification marks
facing up)
J
Figure 1
Left side
Front Leg (FL)
(identification marks
facing down)
Q
Under Arm
brace
FRONT
K
Q
Left side
Rear Leg (RL)
(identification marks
facing down)
Left side
Rear Leg (RR)
(identification marks
facing down)
Under Arm
brace
FRONT
K
Left side
Front Leg (FR)
(identification
marks
facing down)
BACK
Arm
L
Q
Q
1b
1a
Under Arm
brace
FRONT
K
BACK
Arm
LG1 G1
G
G

2b - Attach part ( H ) , Seat Back Assembly , to part ( I ), Seat Bottom Assembly , as shown in Figure 2 see
detail 2 using ( 4 ) of screws ( G1 ) , 2 on each side, tighten screws using a phillips-head screwdriver .
G1
( Detail 2 )
( Detail 1 )
2a - Attach part ( H ) , Seat Back Assembly , to part ( I ), Seat Bottom Assembly you must align the lower front
edge of Yoke to hide the front edge of groove, see detail 1 .
front edge of groove
Front edge of Yoke
( Seat Bottom Assembly )
Seat Back Assembly
Figure 2
2 - Attach parts ( M ) , Glider Base Mid Brace Front & Back , to parts ( P ), Glider Right Base Assembly and part (N)
Glider Left Base Assembly, as show in Figure 3 see detail 3 using ( 8 ) of screw ( C ), 4 on each side and tighten
screws using an Allen Wrench .
Figure 3
Glider Base Mid brace
Front & Back
Glider Right base
Assembly
Glider Left base
Assembly
( Detail 3 )
I
H
M
P
C
N

Figure 5
4 - Attach the Assembly from figure 4, ( Glider Seat ) to Assembly
from Figure 3, ( Glider Base assembly ) as shown in Figure 5 See
detail 7 using for each leg ( 1 ) of joint connector bolts ( B ) ,
( 2 ) washers ( D2 ), ( 1 ) Lock washers ( E2 ) and ( 1 ) hex nuts
( F2 ), tighten bolts using an allen Wrench and also an adjustable
wrench. Follow the same instructions for right side of glider base.
B
D2
E2
F2
3,a - Attach part ( J ) , Right side front and rear leg assembly , to assembly from Figure 3 as shown in Figure 4,
Make sure identification marks ( FR ) and ( RR ) are facing inside towards the seat see detail 4, using ( 2 ) of
joint connector bolts ( A ), ( 2 ) washers ( D1 ), ( 2 ) lock washers ( E1 ), ( 2 ) hex nuts ( F1 ), see detail 5
tighten bolts using an Allen wrench and also an adjustable wrench. Follow the same instructions for left side
front and rear leg assembly.
Q
Left Side
leg Assembly
C
( Detail 6 )
Seat Back
Assembly
H
C
A
( Detail 5 )
J
A
A
D1
E1
F1
identification marks
Right side
leg Assembly
(FR) (RR)
( Detail 4 )
3,b - Attach part ( J ), Right side front and rear leg and part to seat back assembly ( H ), as shown in Figure 4, see
detail 6, using ( 1 ) of lag screws ( C ), tighten screws using and Allen wrench. Follow the same instructions for
left side front and rear leg assembly.
C
( Detail 7 )
Figure 4
CARE AND MAINTENANCE
To clean your product, use mild soap and water. For heavy soil build-ups use any non-abrasive household cleaners
or ask your Sales Representative about Sister Bay Furniture Cleaner.
Please contact our Customer Service Department for assembly assistance, questions or replacement parts at 1-866-947-7632
or email [email protected]. Our Customer Service Department is available Monday - Friday from 8:30 a.m. to 4:30 p.m. EST