SKC ULTRA 690-101-NB User manual

ULTRA Passive Samplers without Blank
Cat. Nos. 690-101-NB, -103-NB, -104-NB, and -106-NB
Operating Instructions
863 Valley View Road, Eighty Four, PA 15330 USA
Tel: [phone] • www.skcinc.com
Applications
SKC patented* ULTRA®Passive Samplers provide for low ppb to ppt detection of
organic vapors in ambient and indoor air.
Performance Profile
Sampling Rates: Go to the SKC Passive Sampling Guide at
www.skcinc.com/catalog/passive-guide.php.
Analysis: Thermal desorption (TD); gas chromatography (GC)
See Analysis Instructions at www.skcinc.com/instructions/40125.pdf.
Shelf-life: 30 days from date of manufacture. Store at ≤39.2 F (4 C).
* U.S. Patent No. 6,607,581
www.skcinc.com
Sliding cover in open
(sampling) position
Sliding cover in
closed position
Back view
Clip
Diffusion holes
(sample sorbent
compartment)
Sliding
cover
Clip
Sample
compartment
Sliding
cover
Clip
Sample sorbent
compartment
Plugs
Empty
compartment

Sampling
1. Open the pouch. Remove the sampler.
a. Do not discard the pouch.
b. Store the pouch in a clean, organic solvent-free
environment.
2. Record the following:
a. Sample ID on the pouch and sampler
ID label
b. Sampling location on the pouch
c. Date sample taken on the pouch
Do not use Sharpie®markers or equivalent to
mark the label or pouch as these can off-gas
VOCs.
3. Clip the sampler(s) in an appropriate location.
a. Indoors: Clip the sampler(s) to a stand
accessory (Cat. No. 690-302) and locate at an
appropriate height.
b. Outdoors: Clip the sampler(s) inside the
shelter (open on two ends and boom to allow
air to flow freely). Hang the shelter securely at
the appropriate height.
Ensure the diffusion holes in the sampler are not
obstructed in any way.
4. Start sampling: Slide the sampler cover to the
open position (diffusion holes visible). Write the
sample start time on the pouch label.
5. Stop sampling: Slide the sampler cover to the
closed position (arrow and SKC visible). Write
the sample stop time on the pouch label.
Important: Measure and record ambient temperature
and atmospheric pressure. Include in information sent
to the laboratory.
6. Place the sampler in its resealable pouch
immediately after sampling.
Ensure the sample ID on the sampler matches
the sample ID on the pouch.
1
2
3a
3b
Sampler
I.D. label
4
5
6
Clip
Diffusion holes
(sample sorbent
compartment)
Sliding cover
Clip
Sample compartment
Sliding cover

7
8
&
7. Seal the pouch(es). Place the pouch(es) in a
container with a cool pack.
8. Use expedited shipping to send the sample(s),
pertinent information, and Chain of Custody
form(s) to a laboratory for analysis.
Storage
Before Sampling: Up to 30 days at ≤39.2 F (4 C) in a clean, organic solvent-free
environment
After Sampling: 21 days at ≤39.2 F (4 C) in a clean, organic solvent-free
environment
Ordering
ULTRA Passive Samplers, pk/5, prefilled with: Cat. No.
Anasorb®GCB1,#‡ 370 mg 690-101-NB
Chromosorb®106,#¥ 285 mg 690-103-NB
Tenax®TA,#253 mg 690-104-NB
Carbopack X, 400 mg 690-106-NB
# Limited shelf-life; see Storage above
‡ Comparable to Carbopack B
¥ Go to www.osha.gov and search on ULTRA for additional information on sampling rates for Chromosorb 106.
Sampling Accessories
Stand for Indoor Sampling 690-302
Shelter for Outdoor Sampling 690-303
Analysis Accessory
Thermal Desorption Tube, Perkin Elmer, 0.25-inch OD x
3.5-inch length, includes screens and end caps, ea P226530
SKC Limited Warranty and Return Policy
SKC products are subject to the SKC Limited Warranty and Return Policy, which
provides SKC’s sole liability and the buyer’s exclusive remedy. To view the complete
SKC Limited Warranty and Return Policy, go to hp://www.skcinc.com/warranty.

Form 40130 Rev 1807