SkyLink GTR SMART BUTTON G6VR User manual

1. INTRODUCTION
Model G6VR
Garage Door
Remote Control
2. INSTALLATION
Unplug the power cord of your garage door opener
before installation to ensure power is not connected.
WARNING
GTRSmartButtonTM
The GTR Smart ButtonTM replaces most garage door “push buttons”
or “wall consoles”. There are 2 different kinds of “push buttons”.
1) Single button
2) Multi-Function Wall Console
1) Single button
If your garage door opener comes equipped with a single button “push
button”, you can replace the existing push button with Skylink®Smart
ButtonTM GTR. Please follow the procedures below.
1. Remove the existing push button by removing
the screws.
2. Disconnect the 2 wires that are connected to
the existing push button.
3. Connect the 2 wires from the existing wall
button to the GTR Smart ButtonTM. Twist the 2
wires together with the wire connector
provided. Polarity does not matter, so simply
pick one wire from the existing wall button, and
connect it to one of the wires on the Smart
ButtonTM. Do the same for the 2nd wire.
4. After connecting the wires, mount the Smart
ButtonTM on to the wall with 2 screws.
5. Plug in the AC cord of the garage door opener.
The red light on the Smart ButtonTM should flash
15 seconds after plugging in the power. The
red light will not flash immediately after
plugging in the power, which is normal. The
Smart ButtonTM is now ready to be operated.
Note: Straighten up the antenna to improve signal reception.
Remove
existing
wires
Mounting
Accessories
2. INSTALLATION (CONT)
Smart ButtonTM
2) Multi-Function Wall Console
Multi-Function Wall Console normally comes with 3 buttons that can be
used to:
1) operate the garage door opener lighting,
2) lock the receiver so it doesn’t accept
remote control operation, and
3) push button for door opening / closing
Congratulations on your purchase of the Skylink®G6VR Universal
Garage Door Remote Control. This is a kit with a universal remote
control and Smart ButtonTM. It is 100% compatible with all garage door
openers. Simply replace the traditional wall button by the Smart
ButtonTM, that’s all for the installation. In this kit, you will find the
following:
Rating of the transformer: 12V DC, 100mA
Diameter of DC plug : 3.5mm
Note: Straighten up the antenna to improve signal
reception.
Universal
Remote Control
(Battery included)
If you have the multi-function wall console, do not replace the wall
console by the Smart ButtonTM. You need to install the Smart ButtonTM in
parallel with your existing wall console.
1. Remove the existing wall console from the wall
by removing the screws.
2. Remove the 2 screws that secure the wires
on the wall console.
3. Connect the wires from the Smart ButtonTM to the
existing wall console. Polarity does not matter,
so simply pick one wire from the Smart ButtonTM,
and connect it to one of the terminals on the
existing wall console. Do the same for the 2nd
wire.
4. After connecting the wires, mount the Smart
ButtonTM on to the wall with 2 screws. Also
mount the original wall console on to the wall.
5. Plug in the AC cord of the garage door opener.
The red light on the Smart ButtonTM should flash
15 seconds after plugging in the power. The red
light will not flash immediately after plugging in
the power, which is normal. The Smart ButtonTM
is now ready to be operated.
6. If the Smart ButtonTM red light does not flash at
all 2 minutes after plugging in the AC cord, your
garage door opener is probably too old.
However, the Smart ButtonTM will still work by
plugging in an adapter (purchase separately).
Please contact Skylink®to purchase the
adapter.
If the red light on the Smart ButtonTM is flashing slowly,
that indicates it is in standby mode. When a valid
remote control signal is received, it will open / close the
garage door.
Simply press the button on the remote control or
Smart ButtonTM, it will open / close the garage door. OPEN /
CLOSE
Programming
Learn additional remote controls
Smart ButtonTM can learn up to 15 remote controls.
To learn additional remote controls, follow the
instructions below:
1. Press the learn button on the side of the GTR.
2. Once the learn button is pressed, the LED will
flash quickly. You may release the learn button.
3. Press the button on the remote control you would
like to program.
4. Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
5. You may now operate the garage door opener
with this new remote control.
Learn
Button
3. OPERATION
Antenna
2 Wire
Connectors
Visor clip

3. OPERATION (CONT)
Erase remote controls
To erase unwanted remote control(s), first erase all remote controls,
then learn the ones you would like to keep.
To erase remote control(s)
1. Press and hold the learn button for approx 10 seconds.
2. The LED will flash rapidly after 10 seconds to indicate all the pro-
grammed remote controls have been erased. You may now release
the learn button.
3. You have erased all the remote controls in the Smart ButtonTM.
6. WARNING
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
4. BATTERY
12 volt alkaline battery (size 23A)
included.
7. FCC
The Garage Door Remote Control is approved by the FCC and it complies with
Part 15 of the FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user’s authority to operate the equipment.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N.101Z482
USPatent. D377458,5680134,5841390, 6005508,6956460
®are registered trademarksof theirrespectivecorporations
©2007 SKYLINK GROUP
8. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
9. CUSTOMER SERVICE
If you would like to order Skylink’s product or have difficulty getting your Skylink
remote control to work, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax [phone]
You can add up to 15 additional transmitters to control the
same receiver. Skylink®offers Keychain Transmitters and
Keypad Transmitters to work with your receiver. For
more information, please visit our website at
www.skylinkhome.com or contact us.
5. ADDITIONAL TRANSMITTER