Skymsen PC-7L User manual

UG0037 - January / 2014
Food Processor-Cutter / Procesador-Cutter
Model / Modelos
PC-7L
CAUTION!
HAZARDOUS MOVING PARTS
Disconnect Power Before
Cleaning or Servicing
!ATENCIÓN!
PARTES MOVIBLES PELIGROSAS
Desconecte de la Red Electrica
antes de la Limpieza o Manutención
Instructions Manual / Manual de Instrucciones
Office
Phone: [phone]
Fax: [phone]
www.skyfood.us[email protected] -
TOLL FREE 1-800-503-7534

SUMMARY / INDICE
1. ENGLISH 01
2. ESPAÑOL 11
PC-7L
PC-7L

01
2
2
2
4
4
4
4
5
5
5
5
5
6
6
SUMMARY
6
7
7
8
8
8
9
10
1.Introduction
1.1.Main Precautions
1.2.Main Components
1.3.Technical Characteristics
1.4.Available Discs
2.Installation and Pre-Operation
2.1.Installation
2.2.Pre-Operation
2.2.1.Cutter Pre-Operation
2.2.2.Processor Pre-Operation
3.Operation
3.1.Starting
3.2.Processor Operation
3.2.1.How to place the Discs
3.2.2. How to feed the Processor
3.3.Cutter Operation
3.4 Cleaning
4.General Safety Advices
5.Problems Analysis and Solutions
5.1. Problems Causes and Solutions
5.2.How to sharpen the Knife Blades
5.3 Electrical Diagram Mod. PC-7L
6. General Advices
10

1.2Main Components
All the components belonging to the machine are built with carefully
selected material suitable for its function, following Siemsen Standards and experience.
1 INTRODUCTION
The Food Processor /Cutter Model PC-7L has been designed to process foods with
efficiency and safety , however an accident may occur even with well trained operators
. It is the owner responsibility to assure the machine proper and safe operation , in
accordance with the instructions of the present Manual and of the local laws .
1.1 Main Precautions
The Food Processor may be a dangerous machine when incorrectly used . Cleaning and
maintenance shall be made only by skilled operators .Therefore to avoid accidents , read
carefully all the following instructions :
. TO BE USED only by skilled operators .
. BEFORE cleaning or maintenance unplug the machine from electric power source.
. NEVER use tools not belonging to the machine to help operation .
. BEFORE to switch ON the machine check if the processor Disc No. 01 ( Pic. 03) and
the Disc Housing No.02 ( Pic 01 ) , as well as check if the Cutter Blade No.01 ( Pic 04)
and the Cutter Housing are duly held on their position .
. NEVER remove the Disc Housing before the machine is completely still .
. NEVER open the Cutter Lid without being sure the blade is still .
. NEVER put the hand inside the feeding throat , nor inside the processed food exit
opening . Keep hands away from any moving parts .
. NEVER switch ON the machine with wet hands or clothes .
. DO NOT wear long or large clothes during operation .
. NEVER throw water or other liquids directly on the electric motor , electric switch , or
any other electrical component .
.ALWAYS install the machine in wide and clear working area , far from the reach of
children and visitors .
. NEVER operate the machine without the warnings and the Instruction Manual out of
reach .
. NEVER let the machine alone during operation .
. ALWAYS ground the machine in accordance with local rules .
. STOP the machine immediately if unusual noises are heard , or when having the
feeling that some kind of accident might occur .
. CONTACT your Dealer , if any problem arises with the machine installation or operation
.
02

03
1.Large stump
2.Discs Housing
3.Cabinet
4.ON/OFF switch
5.Feeding throat
6.Small stump
7.Fastening handle
8.Warning Label
9.Collecting Bowl
10.Cutter Housing
11.Cutter Lid
12.Cutter Lid handle
13.Housing Base
01 -Blade
01 - Disc
02 - Central Shaft
Picture - 01
Picture - 03
01
02
Picture - 02 Picture - 04
01
04
03
08
02 13
05
01 06
07
10 11
09
01
12
01 -Discs Housing

04
1.3 Technical Characteristics
1.4 Available Discs
The Processor/Cutter mod PC-7L is a machine capable to produce several different cuts ,
as slicing, shredding , grating .
It may process practically almost all kinds of products , maintaining their nutritional
proprieties and color .
The below Table 02 informs the discs normally supplied with the processor , giving their
sizes and their code numbers :
TABLE 01
Table 02
Characteristics M.U.
PC-7L
Processor Cutter
[V] 110/220 110/220
[Hz] 50 or 60 50 or 60
[Hp] 0,5 0,5
[kW/h] 0,4 0,4
[mm] 620 570
[mm] 320 320
[mm] 450 450
[kg] 24,5 24,5
Voltage
Frequency
Power Rating
Consumption
Height
width
length
Net weight
Gross weight [kg] 27 27
Name
cutting size
code number
Shredder 3 3mm diameter 23016.2
Shredder 5 5mmdiameter 23015.4
Shredder 8 8mmdiameter 23014.6
Scallop Cut 2mm thick 20038.7
Slicing 3mm thick 20037.9
Grater 20043.3
2.1 Installation
The Processor /cutter shall be installed on a steady and flat surface . The installation
shall be made only by qualified or experienced personnel . The surface should be 850
mm high above floor level .
Check the voltage . The motor voltage shall be the same as the voltage of the electric
source . Grounding is mandatory . Contact your supplier in case any problem or question
arises during installation .
2. INSTALLATION AND PRE-OPERATION
Observation : the frequency will be the frequency indicated on the motor .

05
3.1 Starting
Be sure the discs housing or the cutter housing are correctly fastened .
To start the machine press the ON/OFF switch .
3. Operation
OBSERVATION
For your own safety read all the labels fixed on the machine .
2.2 - Pre-operation
The machine shall be steady , no movement is supposed to occur on the supporting
surface . Wash all the part in contact with the food with neutral soap and hot water, then dry
them .
The equipment is now ready to be used .
Important
Before to place the Discs Housing on the machine body check if the disc is place
correctly to avoid damages to the equipment .
Important
Place the Cutter Housing in its correct position , put the blade inside the bowl.
Check if both are well fitted to avoid damages to the equipment .
2.2.1 Cutter
2.2.2 Processor
Important
Switch OFF the machine when it is desired to change some equipment . Be sure
the machine is completely still before to withdraw any equipment .
service company ("Service Company"). Products held at commercial facilities and weighing
less than seventy (70) lbs. must be taken or shipped, shipping charges are prepaid, either
to SKYFOOD's facility or to a Service Company. Mileage or travel time will NOT be paid.
SKYFOOD offers a limited on-site warranty for products ONLY held at commercial
facilities, whose net weight exceeds seventy (70) lbs., provided they are installed in a
location that is within a thirty (30) mile radius of a Service Company. End Users are
responsible for all extra travel and mileage rates. In this case, warranty services will be
provided during regular business hours.
This product will be replaced or repaired under warranty, for a period of (1) year,
beginning from the date of purchase by the original purchaser/user (“End User”).
Accessories will be replaced or repaired under warranty, for a period of (30) days,
beginning from the date of purchase by the original purchaser/user (“End User”).
This warranty shall not take effect until a properly completed and executed WARRANTY
REGISTRATION form has been received by SKYFOOD EQUIPMENT, LLC, wit hin thirty
(30) days from the date of purchase. The WARRANTY REGISTRATION is available either
in the Instruction Manual of every Product or at SKYFOOD’s website www.skyfood.us. The
End User must fill out the WARRANTY REGISTRATION form and send it to SKYFOOD
according to the instructions posted on the referred website. Failure to do so will VOID
the warranty.
For questions or assistance, do not return the product or accessories to the store, please
call Toll Free 1 -800-503-7534 for Customer Support, or visit the Customer Service section
of www.skyfood.us. For faster service please have the items name, serial number, and
proof of purchase for the operator to assist you.
SKYFOOD reserves the right to change the terms of its limited warranty at any time
without any prior notice. It also reserves the right to change the design and
specifications of its equipment or any related documentation at any time. The end
user is not entitled to upgrades or refunds resulting from these changes.
Updates
These Terms and Conditions were last updated on August 22th, 2011.

06
WRONG wayCORRECT way
3.2.2 - How to feed the Processor
IMPORTANT
NEVER use tools not belonging to the machine to help operation , and particularly do
not use the hands . Use always the stumps No.01 and No.06 (Pic.01 ) to feed the
machine in .
The Processor/Cutter is a machine operating at high speed , therefore it shall be fed fast .
To feed the machine remove the stumpNo.01 or No. 06 ( Pic.01 ) place the product to be
processed inside the correct throat and push it down . always use the proper stump .
To process small vegetables , such as carrots , cucumbers or similar use the small throat
with the small stump No. 06 ( Pic.01 ) .
Use the stumps as per the
below picture
CORRECT way WRONG way
NEVER use the small stump
inside the large throat .
Irreparable damages will occur
3.2 - Processor Operation
3.2.1How to place the Discs
With the machine switched OFF and the Disc still, remove the stumps No.01 or No.06 (
Pic.01 )and remove the discs housing No 02 ( Pic 01 ) . To remove the lid it is necessary to
lose the handles No. 07 ( PIC.01 ) and turn the lid No 02 ( PIC.01 ) counterclockwise about
¼ of a turn .
Be careful with the Disc. Grab the desired disc and fit it on the central shaft No.02 ( Pic. 03 )
turning it counterclockwise to have it perfectly fastened .
Fit the lid No.02 ( PIC.01 ) and be sure it is perfectly fastened , tightening the handles No. 07
( Pic. 01 ) .
IMPORTANT
Do not apply to much force to push down the food with the stump.
To obtain a better performance use refrigerated food products .
SKYFOOD EQUIPMENT LLC - SERVICE
For questions or assistance with products FLEETWOOD by SKYMSEN and SKYMSEN,
call SKYFOOD EQUIPMENT Toll Free : 1-800-503-7534, 24h Customer support, or visit
the Customer Service section of www.skyfood.us.
SKYFOOD’S LIMITED WARRANTY
Unless otherwise specified,new FLEETWOOD by SKYMSEN and SKYMSEN products,
excluding accessories, sold by SKYFOOD EQUIPMENT, LLC. (“SKYFOOD”), for use only
in the continental United States (collectively, “Products” or singularly, “Product”), are
warranted to be free from defects in materials and workmanship for a period of one (1)
year from the date of purchase by the original purchaser/user (“End User”). Several new
products and accessories may be warranted for a period other than one (1) year while
others may be subject to travel limitations, as specified on the products Instruction Manual.
Proof of purchase must be presented; if not this warranty will be VOID. No warranty is
given or implied to a subsequent transferee or any other third party. This warranty is
expressly conditional upon SKYFOOD being notified of any defects in materials or
workmanship within five (5) days of its occurrence, within the warranted time period. If a
notice of a claim under this warranty is timely made by the End User, SKYFOOD or a
SKYFOOD’s designated service company (“Service Company”), will repair or replace the
Product, at SKYFOOD’s discretion, subject to the additional conditions hereinafter
described.
This warranty shall not apply if damage occurs from improper installation or maintenance
performed by an unauthorized service company (“Service Company”), wrong voltage, nor
to the extent that Products or parts have been used other than in conformance with
operating and maintenance instructions, subjected to misuse or abuse or damaged by
accident, acts of God, abnormal use, stress or any other matter unrelated to SKYFOOD,
and beyond its reasonable control. This warranty does NOT cover service labor and
travel to perform adjustments on products and/or accessories. In addition to wear and
tear of certain items, such as, but not limited to; glass parts, blades, stones, chopper
cutting knives, plates, slicing knives, cutting disc, gaskets, oil changes, sealing tape, heat
seal wires, worm gears, self-lubricating bushings, carbon brushes for electric motors, and
other parts expendable by nature and that need to be replaced frequently. Electrical
components are subject to natural wear and tear, and are NOT covered by this
warranty. THIS WARRANTY EXCLUDES ALL ORAL, STATUTORY, EXPRESS OR
IMPLIED WARRANTIES WHICH MAY BE APPLICABLE TO SKYFOOD, INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE. Under no circumstances shall SKYFOOD be
liable for loss of use, revenue or profit or for incidental or consequential damages.
SKYFOOD shall under no circumstances be liable for any loss, damage, concealed
damage, expense or delay of goods for any reason when said goods are in the custody,
possession or control of third parties selected by SKYFOOD to forward, enter, clear,
transport, or render other services with respect to such goods. The sole and exclusive
remedy for breach of any warranty is limited to the remedies provided in the paragraph
above.
All products held at non-commercial facilities or domiciles, must be taken or shipped,
shipping charges prepaid, either to SKYFOOD's facility or a SKYFOOD's designated

All the removable part shall be washed with hot water and neutral soap.
Follow the below steps to remove these parts :
. Switch the machine OFF , and after, unplug it from electric power source .
. Remove the stumps No.01 or No. 06 ( Pic.01 ) and the Collecting Bowl No.09 (Pic01) .
. Lose the handles No. 07 ( Pic 01 ) .
. To remove the Disc Housing ( Processor ) and the Knife Housing ( Cutter ) , proceed as
shown on pictures Pic 02 or Pic 04
. To withdraw the Disc , be careful with its knives . Grab the disc and turn it counterclockwise ,
and then lift it .
. To remove the Cutter Knife , just lift it .
. Wash the removed parts with hot water and neutral soap . Using a wet cloth clean the Body
and the disc Housing , then dry them .
07
3.4 Cleaning
3.3 Cutter Operation
IMPORTANT
BEFORE to clean the machine unplug it from electric power source. Always be sure that the
Disc or the Blade are completely still .
IMPORTANT
Be careful when washing the disc and its knives . Do not hit the discs with hard
objects , to avoid to damage them .
Tabela 3
. See the machine Technical Characteristics .
. Place the Bowl on the Body
. Turn the bowl counterclockwise until it is well fastened , then tight the handles
No.07 ( Pic. 01 ) .
. Place the blade on the central shaft .
. Cut the products, such as tomatoes, potatoes , and others , in medium size pieces
and then place them inside the bowl . It is recommendable to place all the products
inside the bowl at the same time .
. Place the lid on the bowl and tighten the handles of the lid to have it well fastened .
. Switch the machine ON , and check the below Table 03 to know the approximate
time needed to process each product .
. If it should be necessary to add some more products during operation , lift the small
rubber lid and insert them .
. When the operation ends, withdraw the bowl with the blade still inside to avoid
leaking.
Tomato Sauce
Mayonnaise
Smashed Potatoes
Dried Cod
Peanut Cream
Chestnut Cream
Walnut Cream
4 to 6
14 to 20
6 to 10
3 to 6
4 to 6
4 to 6
4 to 6
Liver
Salmon
Lobster
Anchovy
Onions
Garlic
Parsley
SOUP SEASONIG
4 to 8
3 to 6
3 to 6
3 to 6
2 to 4
2 to 4
2 to 4
VARIOUS seconds PATÉ seconds
MEAT seconds FRUITS seconds
Meat
Hanburger
Meat Paté
Meatball
5 to 10
3 to 6
6 to 10
5
Fruit Salad
Apple jam
Pear jam
Peach jam
2 to 4
3 to 6
3 to 6
3 to 6
20
5.3 Diagrama Eléctrico Mod. PC-7L
Chave Liga/Desliga
6. CONSEJOS GENERALES
- Do not wear loose fitting clothes while operating the unit. Do not use bracelets or any other piece of jewelry. Have
your hair always shortened and held up (use hair fishnets if necessary) in a way it cannot reach any part of the
machine. Roll up any loose sleeves.
- SKYMSEN is not responsible for any harm or injury caused by the negligent or inappropriate use of this
equipment by any operator. This equipment must be operated only by persons whose age equals or exceeds 18
years old, in a safe and sound state of mind, free from the influence of any kind of drugs and alcohol, that received
proper training and instructions regarding the correct operation of this machine, that are wearing correct and
authorized safety clothes. All and any kind of modifications carried on and applied to this machine immediately
nullifies any kind of warranty and may result in harm and injuries to the individuals operating this machine and to
individuals that are located in the machine surrounding areas while it is being operated.
- Under no circunstances place your hands in the moving parts of the machine while it is being used. Make sure the
machine has come to a complete stop before acessing the processed ingredients.

08
4. General Safety Advices
.Always switch OFF , and unplug the machine before cleaning and maintainance .
. Keep enough space around the machine to avoid accidents.
.ALWAYS keep the floor dry , wet and slippery floor may cause accidents .
.ALWAYS switch of the machine in case of electricity cut off .
. NEVER let dirt or water get into electrical or mechanical components .
. DO NOT MODIFY the machine original characteristics .
. DO NOT tear or remove the safety labels or the identification .
The Processor / Cutter PC-7L has been designed to need a minimum maintainance .
However some problems may arise due to normal wear during the machine life .
If some problem arises with your Processor/Cutter, check Table 04 , were some possible
solutions are recommended
* Service life – 2 years for regular work shift
5 Problems Analysis and Solutions
5.1Problem Causes and Solutions
19
5.2 - Como afilar las cuchillas
Las cuchillas son removibles, por lo tanto, pueden ser facilmente afiladas, sin embargo,
debese tener especial atencion para mantener el angulo de corte. Las cuchillas deben ser
afiladas con una lija delgada o con una piedra de afilar. Use una llave de tornillos para
remover las cuchillas.
Problemas Causas Soluciones
* Los Manipulos
Fig.01 estan flojos.
(Nº07)
* Acumulo de suciedad entre
la Base de la Tapa Nº12
(Fig.01) y Tapa del Discos Nº2
(Fig.01). y Tapa del Cutter.
* Remova la Tapa y
reposicione el Disco.
* Olor de quemado o Humo.
* La maquina liga, pero el
disco demora a girar.
* Ruídos anormales.
* Vaciamiento por la Tapa.
* Problema en el motor o
otras partes electricas..
* Correas deslizando.
* Capacitor de arranque del
motor defectuoso. * Llame a su Distribuidor.
* Apriete los Manipulos
( Nº07) Fig.01.
* Apriete los Manipulos
(Nº07) Fig.01.
* Haga la limpieza
conforme indicado en el
* Llame a su Distribuidor.
* Problema en el circuito
electrico interno o externo de
la maquina.
* Averigue si el enchufe
esta conectado a la red
* Corte Irregular.
* El disco para durante la
operacion.
* Cuchillas sin corte. * Afi le la s c uch ill as
conforme indicado en el
iten Nº10. (Como afilar las
* Llame a su Distribuidor.
* Llame a su Distribuidor.
Tabla - 04

09
5.2 - How to sharpen the Knife Blades
The Blades may be removed, therefore may be easy sharpened , however special attention
must be given to keep the right original cutting angle . The blades must be sharpened using
a sharpening stone or a thin sandpaper . Use a screw driver to remove the blades .
PROBLEMS CAUSES SOLUTIONS
Table - 04
Sharpen blades as per
item No. 5.2 ( how to
sharpen Blades )
Check if the machine
plug is on its socket.
Call the dealer
Call the dealer
Call the dealer
Remove the lid and
replace the disc.
Call the dealer
Tight the handles
No. 07 ( Pic. 01 )
Fasten the handles
Clean the machine in
accordance with item No.
3.4 cleaning .
Blunt blades
Electric Power shortage
Internal or external
electric wiring problem
Electric motor or other
electric parts problem
Motor capacitor failed
Disc not correctly fitted .
Bearing failure.
Lid not fastened
Handles N.07
(Pic 01 ) are loose .
To much dirt between
Housing Base Nº 13 (Pic 01)
and Disc Housing Nº 2 (Pic
02) and Cutter Housing
Nº10(Pic 01)
Irregular cutting
The disc stops during
operation
Smoke or burn smell
The machine switches ON
but the Disc delays to
start moving
Unusual noises
Vazamento pela Tampa
18
4. NOCIONES DE SEGURIDAD
SIEMPRE desligue la maquina antes de la limpieza y manutención.
PROVIDENCIE espacio suficiente alrededor de la maquina para evitar accidentes.
SIEMPRE mantenga el suelo seco. Suelos mojados pueden causar deslizamientos.
SIEMPRE desligue la maquina cuando hubiera caida de energia.
NUNCA deje suciedad o agua entrar en los componentes electricos y mecánicos de la
maquina.
NO modifique las caracteristicas originales de la maquina.
NO remova o rompa las calcomanias de seguridad y identificación.
El Procesador Cutter fue proyectado para necesitar el minimo de
manutención. Por lo tanto, pueden ocurrir algunas irregularidades en su funcionamiento,
debido al desgaste natural causado por el uso del equipo.
Caso haya algun problema con su Procesador Cutter, verifique la Tabla-
04, donde estan descritas algunas posibles soluciones recomendadas.
* La vida de servicio - 2 años para la jornada de trabajo normal
5 - ANALISIS Y RESOLUCION DE PROBLEMAS
5.1 Problemas, Causas y Solucciones

10
5.3 Electrical Diagram Model PC-7L
Switch ON/OFF
Todas las partes removibles de la maquina deben ser lavadas con agua
caliente y jabón neutro. Siga los siguientes pasos para remover las partes removibles de la
maquina:
-Desligue la maquina y en seguida desconecte el enchufe de la red electrica.
-Remova los Empujadores no.01 o no. 06 (Foto 01) y el Recipiente no.09 (Foto 01).
-Afloje los Manipulos no.07 (Foto 01) .
-Para remover la Tapa de los Discos o el Vaso del Cutter, haga como indicado en la Foto-
02 o Foto-04.
-Cuidado con las cuchillas de los Discos, agarre el Disco y lo gire en el sentido anti horario y
en seguida lo tire para arriba.
- Para remover la cuchilla del Cutter solamente la tire para arriba.
-Lave todas las partes removibles con agua caliente y jabón neutro, y con un paño húmedo
limpie el Gabinete y el Soporte de los Discos. En seguida los seque.
17
3.4 Limpieza
3.3 Operación del Cutter
-Vea los Datos tecnicos de la maquina.
-Coloque el vaso sobre el Gabinete del motor.
-Gire el vaso en el sentido anti horario hasta que se quede fijado.
-Instale las cuchillas en el Eje Central.
-Coloque dentro del vaso ingredientes de tamaño medio, tales como: papas, tomates, y
otros. Es recomendable colocar todos los ingredientes al mismo tiempo dentro del vaso.
-Coloque la tapa sobre el vaso y apriete los tornillos para que la tapa se quede fijada.
-Ligue la maquina. Cheque la Tabla abajo para saber el tiempo aproximado para preparar
cada producto.
-Si fuera necesario poner ingredientes en el vaso durante la operación, remova la tapa de
goma negra y los ponga.
-Al terminar la operación saque el vaso con la cuchilla aún adentro para evitar vaciamiento.
IMPORTANTE:
ANTES de la limpieza de la maquina desconectela de la red electrica. Siempre esté seguro
que el Disco o la Cuchilla está completamente parada antes de remover la Tapa.
IMPORTANTE:
Atención al lavar los Discos por sus partes cortantes. No golpee los Discos con
objetos rígidos, evitandose así dañarlos.
TABLA
3
- Do not wear loose fitting clothes while operating the unit. Do not use bracelets or any other piece of
jewelry. Have your hair always shortened and held up (use hair fishnets if necessary) in a way it
cannot reach any part of the machine. Roll up any loose sleeves.
- SKYMSEN is not responsible for any harm or injury caused by the negligent or inappropriate use of
this equipment by any operator. This equipment must be operated only by persons whose age equals
or exceeds 18 years old, in a safe and sound state of mind, free from the influence of any kind of drugs
and alcohol, that received proper training and instructions regarding the correct operation of this
machine, that are wearing correct and authorized safety clothes. All and any kind of modifications
carried on and applied to this machine immediately nullifies any kind of warranty and may result in
harm and injuries to the individuals operating this machine and to individuals that are located in the
machine surrounding areas while it is being operated.
- Under no circunstances place your hands in the moving parts of the machine while it is being used.
Make sure the machine has come to a complete stop before acessing the processed ingredients.
6. GENERAL ADVICES

11
1.2 Principales Componentes
1.3 Características Técnicas
1.4 Discos Disponibles
1. Introducción
12
1.1 Principales Precauciones
12
12
14
14
2. Instalación y Pre-Operación
2.1 Instalación
2.2 Pre-Operación
2.2.1 Pre-Operación del Cutter
2.2.2 Pre-Operación del Procesador
14
14
15
5
4. Nociones de Seguridad - Genéricas
5. Análisis y Resolución de Problemas
5.1 Problemas, Causas y Soluciones
5.3 Diagrama Eléctrico Mod. PC-7L
5.2 Como afiar las cuchillas
3. Operación
3.1 Acionamiento
3.2 Operación del Procesador
3.2.1 Colocación de los Discos
3.4 Limpieza
3.2.2 Procedimiento para Alimentación
3.3 Operación del Cutter
3.3.1 Colocación de la Cuchilla
3.3.2 Procedimiento para Alimentación
15
15
16
16
SUMARIO
17
17
17
17
18
18
18
19
20
16
Modo
INCORRECTO
Modo
CORRECTO
3.2.2 - Procedimiento para la Alimentación
IMPORTANTE:
NUNCA use herramientas que no pertenezcan a la maquina para ayudar en la
operación, mucho menos las manos. Use siempre los Empujadores no.1 o no.06
(Foto 01) para la referida operación.
El Procesador Cutter PC-7L es una maquina que trabaja en alta velocidad,
por lo tanto necesita ser igualmente alimentada.
Para alimentar la maquina remova el Empujador no.01 o el no.06 (Foto
01), coloque el producto a ser procesado dentro de la Entrada de Alimentación y lo empuje
para abajo usando siempre el Empujador.
Para procesar alimentos pequeños como: zanahoria, pepinos y similares,
use la entrada móvil con el empujador pequeño no. 06(foto-01).
Use los Empujadores
conforme Figura abajo.
Modo CORRECTO Modo INCORRECTO
Nunca use el Empujador Pequeño en la
entrada Grande, pues daños
irreparables van a ocurrir.
3.2 - Operación del Procesador
3.2.1 Colocación de los Discos
Con la maquina desligada y el Disco parado, remova los empujadores no.01 o no.06 (Foto
01) y remova la Tapa de los discos no.02 (Foto 01). Para remover la Tapa es necesario
aflojar los Manipulos no.07 (Foto 01) y girar la Tapa no.02 (Foto 01) en el sentido anti
horario por aproximadamente ¼ de vuelta.
-Tenga cuidado con el Disco. Agarre el Disco deseado y lo encaje en el Eje Central no.02
(Foto 03) girandolo en el sentido anti horario para obtener su perfecto trabamiento.
-Encaje la Tapa no.02 (Foto 01) asegurandose que la misma quede perfectamente
trabada, para eso apriete los Manipulos no.07 (Foto 01).
IMPORTANTE:
No haga mucha fuerza para empujar el alimento para abajo con el Empujador.
Para obtener un mejor desempeño use alimentos refrigerados.
6. Consejos Generales
20

1.2 Principales Componentes
Todos los componentes que incoporan la maquina son contruidos con materiales
cuidadosamente seleccionados para cada función, dentro de los padrones de testes y de la
experiencia SIEMSEN.
12
1. INTRODUCCIÓN
AVISO A LOS PROPIETARIOS Y OPERADORES
El Procesador Cutter Modelo PC-7L es desarollado para procesar alimentos eficientemente y con
seguridad. Aúnque el usuario sea bien entrenado y supervisionado existe la posibilidad de un serio
accidente. Es responsabilidad del propietario asegurar que la maquina sea usada correctamente y
seguramente, siguiendo las instrucciones contenidas en este Manual y los requisitos de las leyes
locales.
1.1 Principales Precauciones.
El Procesador Cutter Modelo PC-7L puede ser una maquina potencialmente peligrosa cuando usada
incorrectamente. Limpieza, manutención o servicio deben ser hechos solamente por operadores
experientes. Por lo tanto, lea todas las siguientes instrucciones con atención para evitar accidentes:
PARAUSO COMERCIAL SOLAMENTE por operadores calificados.
ANTES de la limpieza y manutención de la maquina la desconecte de la red electrica.
NUNCAuse herramientas que no pertenezcan a la maquina para ayudar en la operación.
ANTES de ligar la maquina averigue si el Disco no.01 (Foto 03) y la Tapa no.02 (Foto 01)
del Procesador, o la cuchilla nº1(Foto4) y el vaso del Cutter nº 10 (Foto1) están propiamente seguros
en sus posiciones.
NUNCAremova la Tapa antes de la parada completa del Disco.
NUNCA abra la tapa del Procesador o la tapa del Cutter sin estar seguro de la completa parada del
disco o de la cuchilla.
NUNCA ponga las manos dentro de las Entradas de Alimentación ni en la salida del producto
procesado. Mantenga las manos lejos de las partes movibles de la maquina.
NUNCAconecte la maquina a la red electrica con las manos o ropas mojadas.
NO USE ropas con mangas largas y anchas durante la operación.
NUNCA chorree agua o otro liquido directamente al motor, llave electrica o en cualquier otro
componente electrico.
SIEMPRE instale el equipo en una area de trabajo con luz y espacio adecuados y lejos de niños y
visitantes.
NUNCAopere la maquina sin las calcomanias de Atención y sin el Manual de Instrucciones al alcanze
del usuario.
NUNCAdeje la maquina trabajando sola.
SIEMPRE atierre la maquina adecuadamente de acuerdo a las reglas locales.
PARE la maquina inmediatamente si Usted escuchar ruidos anormales o sentir que accidentes
pueden ocurrir.
CONTACTE a su Distribuidor si hubiera cualquier problema con la instalación y/o operación de esta
maquina.
15
3.1 Accionamiento
Esté seguro que la tapa de los discos o el vaso del Cutter están debidamente
trabados. El accionamiento de la máquina es hecho apretandose la llave liga/desliga
no.4 (foto-01).
3. OPERACIÓN
Observa
fijadas en la máquina, como la que aparece abajo.
ción
Para su mayor seguridad lea todas las etiquetas
2.2 - Pre - operación
Averigue si la maquina esta firme en su posición, no es permitido
movimiento en la superficie del soporte. Lave todas las partes que entran en contacto con
alimentos con agua caliente y jabón neutro, y las seque.
Su equipo está ahora listo para ser usado.
IMPORTANTE:
Antes de colocar la Tapa sobre la maquina averigue si el Disco está bién
posicionado, evitando así daños a la maquina.
IMPORTANTE:
Tras posicionar el vaso del Cutter en su posicion correcta coloque la cuchilla dentro del
vaso, averigue si estan bien encajados, evitando así daños al equipo
2.2.1 Cutter
2.2.2 Procesador
IMPORTANTE
Desligue la máquina siempre que desear cambiar algun equipo. Esté seguro que la máquina está
completamente parada antes de retirar cualquier equipo.

13
01 - Empujador Grande
02 - Tapa de los Discos
03 - Gabinete
04 - Llave Liga/Desliga
05 - Entrada de Alimentación
06 - Empujador Pequeño
07 - Manipulo Traba
08 - Etiqueta Atención
09 - Recipiente
10 - Vaso del Cutter
11 - Tapa del Cutter
12 - Base de la Tapa
01 - Tapa de los discos 01 -Cuchilla
01 - Disco
02 - Eje Central
Foto - 01
Foto - 03
01
02
Foto - 02 Foto - 04
01
04
03
08
02
12
05
01 06
07
10 11
09
01
14
1.3 Caracteristicas Tecnicas
1.4 Discos Disponibles
El Procesador Cutter es una máquina de bancada capaz de realizar
diversos tipos de cortes, tales como: rodajas, deshilados, rallados, podendo procesar
practicamente casi todos los tipos de vegetales, conservando sus propiedades nutritivas,
color y jugos.
En la tabla - 02 estan descritos los discos disponibles, bien como las
dimensiones de corte y el codigo de los mismos.
Tabla - 01
Tabla - 02
Caracteristicas Unidad
PC-7L
Procesador Cutter
Produc Mediación [kg/h] 250 250
Voltaje [V] 220 220
Frecuencia [Hz] 50 50
Potencia [CV] 0,5 0,5
Consumo [kW/h] 0,4 0,4
Altura [mm] 620 570
Ancho [mm] 320 320
Profundidad [mm] 450 450
Peso Neto [kg] 24,5 24,5
Peso Bruto [kg] 27 27
Denominacion
Dimension del Corte Aproximada
Codigo
Disco Deshilador 3 Diametro de 3mm 23016.2
Disco Deshilador 5 Diametro de 5mm 23015.4
Disco Deshilador 8 Diametro de 8mm 23014.6
Disco Ondulador 2 Espesor de 2mm 20038.7
Disco Cortador 3 Espesor de 3mm 20037.9
Disco Rallador x-x-x-x-x-x 20043.3
2.1 - Instalación
El Procesador Cutter debe ser instalado en una superficie nivelada, non
derrapante. Solamente personas calificadas y o experientes deben hacer la instalación.
La altura de la superficie del soporte debe ser de 850mm.
Verifique el voltaje. El voltaje del motor debe ser el mismo que lo de la red electrica. Es
obligatorio el aterramiento de la maquina.
Contacte a su Distribuidor si Usted tiene alguna pregunta o problema en instalar la
maquina.
2. INSTALACIÓN Y PRE- OPERACIÓN