SMART-AVI HDC-IR User manual

TECHNICAL SPECIFICATIONS WHAT’S IN THE BOX
IR-EYE
IR Frequency Range 30 KHz to 80 KHz
Capture Distance Up to 25’
Cable Connector 3.5 mm stereo jack
IR Signal Indicator Green LED
IR-EYE
IR Frequency Range 30 KHz to 80 KHz
Capture Distance Up to 10’
Cable Connector 3.5 mm stereo jack
IR Signal Indicator Red LED
OTHER
Power 12VDC 2A
Cable Link CAT5 568A or 568B
Dimensions 2.5” W x 2.5” D x 1.0” H
Weight .25 lb
Operating Temp. 0°C ~ 40°C / 32°F ~ 104°F
Storage Temp. -20°C ~ 70°C / -4°F ~ 158°F
Relative Humidity Up to 95%
PART NO. QTY DESCRIPTION
HDC-IR 2 IR CAT5 Point to Point
SM-LED 1 IR Emitter
SM-EYE 1 IR Eye (Optional)
PS12VDC2A 2 Power supply 12VDC2A
1 Quick Start Guide
DESIGNED
AND MADE
IN THE USA
NOTICE
The information contained in this document
is subject to change without notice. iPGARD
makes no warranty of any kind with regard
to this material, including but not limited to,
implied warranties of merchantability and
tness for a particular purpose. iPGARD
will not be liable for errors contained
herein, or for incidental or consequential
damages in connection with the furnishing,
performance, or use of this material. No
part of this document may be photocopied,
reproduced, or translated into another
language without the prior written consent
from iPGARD, Inc.
20170518
Toll Free: (888)-994-7427
Phone: [phone]
Fax: [phone]
WWW.iPGARD.COM
A full manual can be downloaded from
www.smartavi.com/hdc-ir/
HDC-IR
IR CAT5 Point to Point Extender
USES A SINGLE CAT5
TO BROADCAST IR
UP TO 1000FT AWAY(333M
Quick Start Guide

The HDC-IR range of products allow the
extension of Infra Red control signals using
single CAT5 UTP (category 5, unshielded
twisted pair) cable. The HDC-IR is the rst
product for this application.
• Uses easy to install, inexpensive CAT5
• Output reaches up to 1000 feet (300 m)
• Sends IR and Power signals over CAT5
• High ground loop immunity
• Built-in lightning, power surge and
transient protection
• Remote Units come with Buffered Outputs
• Compact Enclosure
• Optional power supply for remote unit
• Fully compliant with standard modulated
IR and the latest IRDA
• Fully transparent path for all protocols
and data transfers
• Bi-directional IR
• Supports any IR Remote Control
IR-EYE
IR-LED
INTRODUCTION
FEATURES
HARDWARE INSTALLATION
1. Connect the IR LED to the IR window on the source device.
2. Connect power supply to the unit. Observe LED lighting up indicating power present.
3. Connect IR LED to the IR window on the souce device.
4. Connect the IR Eye to the Receiver.
5. Observe LED lighting indicating power present.Connect the speakers to the Audio Out port.
6. Connect the transmitter to the receiver using Category 5 UTP cable (Purchased separately).
The CAT 5 UTP cable, if purchased in bulk, will be wired using 568A or 568B wiring standard.
7. Once connected, check that the power LEDs on both the receiver and the transmitter are
on, IR status LED is on and RX LED is ashing when Remote control is used indicating that
communication is in progress
IR
CAT5
DVD Player DVD Player DVD Player
IR-In Out-1 Out-2 Out-3
HDC-IR
IR extender over Twisted Pair
HDC-IR
CONTROL
IR-In Out-1 Out-2 Out-3
HDC-IR
IR extender over Twisted Pair
HDC-IR
CONTROL