Smart Technologies SMART Board 600i3 User manual

SMART Board™ 600i3
and SBD600i3 Interactive
Whiteboard System
Configuration and User’s Guide

Product Registration
If you register your SMART product, we’ll notify you of new features and software
upgrades.
Register online at www.smarttech.com/registration.
Keep the following information available in case you need to contact
SMART Technical Support.
Serial Number: ___________________________________________________
Date of Purchase: ___________________________________________________
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Trademark Notice
SMART Board, GoWire, the SMART logo and smarttech are trademarks or registered trademarks of SMART Technologies
ULC in the U.S. and/or other countries. Bluetooth is a trademark owned by Bluetooth SIG, Inc. and is used by SMART
Technologies ULC under license. Sanford, EXPO and EXPO2 are registered U.S. trademarks of SANFORD or its Affiliates.
All other third-party product and company names may be trademarks of their respective owners.
Copyright Notice
©2009 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written
consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not
represent a commitment on the part of SMART.
Patent No. US5448263; US6141000; US6320597; US6326954; US6337681; US6540366; US6741267; US6747636;
US7151533; US7289113; US7499033; CA2058219; and CA2252302. Other patents pending.
11/2009

Introduction
Important Information
Read This Section First
Before you install and use your SMART Board™ 600i3 or SBD600i3 interactive
whiteboard system, read and understand the safety warnings and precautions in this
user’s guide, your projector user’s guide and the included warnings document. These
safety warnings and precautions describe the safe and correct operation of your
interactive whiteboard system and its accessories, helping you to prevent injuries and
equipment damage. You must always ensure that your interactive whiteboard system
is being used correctly.
NOTE
If you own a SMART product other than a SMART Board 600i3 or SBD600i3
interactive whiteboard system, refer to the installation guide for your product
for relevant warnings and maintenance instructions.
In this document, “SMART Board 600i3 interactive whiteboard system” or
“SMART Board SBD600i3 interactive whiteboard system” refers to your
SMART Board 600 or SBD600 series interactive whiteboard and its UF55/UF55w
projector, accessories and optional equipment.
The UF55/UF55w projector included with your system is designed to work only
with certain SMART Board interactive whiteboard models. Contact your authorized
SMART reseller for more information.

ii | INTRODUCTION – IMPORTANT INFORMATION
Safety Warnings, Cautions and Important
Information
WARNINGS – GENERAL
• Failure to follow the installation instructions included with your interactive
whiteboard, or found in this guide, could result in personal injury or product
damage.
• Two people are required to safely mount the projector boom and the
interactive whiteboard on a wall because the items might be too heavy for one
person to maneuver onto their wall-mounting brackets.
• Do not leave cables on the floor where they can be a tripping hazard. If you
must run a cable over the floor, lay it in a flat, straight line and secure it to the
floor with tape or a cable management strip of a contrasting color. Handle
cables carefully and avoid excessive bending.
• To reduce the risk of fire or electric shock, do not expose any component
of your SMART Board interactive whiteboard system to rain or moisture.
• When mounting the projector boom on a framed wall, you must attach both
the mounting bracket and safety tether to a stud to safely support the
projector’s weight. If you use only drywall anchors, the drywall can fail,
resulting in product damage and possible personal injury.
• If you remove the bolt supporting the limit strap, the projector’s boom will be
free to swing. Make sure that the bolt is tightened, and never remove it from
the unit without supporting the projector boom first.
• Do not climb (or allow children to climb) on any part of your
wall-mounted SMART Board interactive whiteboard system.
Climbing on your interactive whiteboard or the
UF55/UF55w projector’s boom could result in personal
injury or product damage. Do not climb on, hang from or
suspend objects from the projector’s boom.
• Cleaning a boom-mounted projector may result in a fall or injury.

iii | INTRODUCTION – IMPORTANT INFORMATION
WARNINGS – PROJECTOR
• Refer to the safety warnings and precautions published in the UF55/UF55w
projector manual.
• Do not stare (or allow children to stare) directly into your projector’s beam
of light. Instruct children not to look in the direction of this beam of light.
Encourage users to keep their back to the projector when working at the
interactive whiteboard. Before they turn to face the audience, users should
step sideways, out of the projector’s beam.
• Do not attempt to service the projector other than performing routine lamp
replacement. Other than the lamp module, there are no user-serviceable parts
inside the unit.
• This projector detects its own remaining lamp life. Replace the lamp when a
lamp life warning message appears. If you continue to use the projector after
the replacement message appears, the lamp might shatter or burst, scattering
glass throughout the projector head.
• If the lamp has shattered or burst:
– Call your authorized SMART reseller for instructions. Do not attempt
to replace the lamp.
– Do not touch the glass fragments because they might cause injury.
– Leave and then ventilate the area where the lamp shattered or burst.
– Wash your hands thoroughly if you have come in contact with
lamp debris.
– Thoroughly clean the area around the projector, and then discard any
edible items placed in that area because they might be contaminated.
• You must remove the projector from the projector’s boom before servicing
the lamp.
– Two people are required to remove and replace the projector.
– Replacing the lamp in a boom-mounted projector might result in a fall
or injury.
– Uncovering the lamp while the projector is mounted on the boom might
lead to product damage or personal injury from falling pieces of glass
if the lamp is broken.

iv | INTRODUCTION – IMPORTANT INFORMATION
• When replacing the projector lamp:
– Turn the projector off and wait 30 minutes for the lamp to cool completely
before removing the projector from the boom.
– Do not remove any screws other than those specified in the lamp
replacement instructions.
– Wear protective eyewear while changing the lamp. Failure to do so can
cause injury or loss of eyesight if the lamp shatters or bursts.
– Use only replacement lamps approved by SMART Technologies. Contact
your authorized SMART reseller for replacement parts.
– Never replace the lamp assembly with a previously-used lamp assembly.
– To prevent premature lamp failure or exposure to mercury, always handle
the fragile lamp assembly with care. Use gloves when touching the lamp.
Do not touch the lamp with your fingers.
– Recycle or dispose of the lamp module as hazardous waste,
in accordance with local regulations.
• When returning the projector to the boom, replace all of the screws that you
removed when you removed the projector. Failure to do so can result in the
projector falling from the boom, causing injury or equipment damage.
• To reduce the risk associated with a leaking battery in your projector’s remote
control:
– Use only the specified coin-cell type battery.
– Orient the battery’s plus (+) and minus (-) terminal according
to the markings on the remote control.
– Remove the battery when the remote control is unused for an extended
period.
– Do not heat, disassemble, short or recharge the battery, or expose it to
fire or high temperatures.
– Avoid eye and skin contact if the battery has a leak.
– Dispose of the exhausted battery and product components in accordance
with applicable regulations.

v | INTRODUCTION – IMPORTANT INFORMATION
CAUTIONS
• Do not operate this unit immediately after moving it from a cold location to a
warm location. When the unit is exposed to such a change in temperature,
moisture could condense on the lens and crucial internal parts. Allow the
system to reach room temperature before operation to prevent possible
damage to the unit.
• Do not place the unit in hot locations, such as near heating equipment.
Doing so could cause a malfunction and shorten the life of the projector.
• Make sure that an electrical socket is near to your SMART product and
remains easily accessible during use.
• Do not add any extra weight or apply pressure to the UF55/UF55w projector
boom, the wall-mounted interactive whiteboard or its pen tray. SMART
designed the brackets to support only the weight of the components during
normal use.
• For operating safety and to prevent damage to your interactive whiteboard,
connect the included USB cable only to a computer that has a USB compliant
interface and that bears the USB logo. In addition, the USB source computer
must be compliant with CSA/UL/EN 60950 and bear the CE mark and CSA
and/or UL Mark(s) for CAS/UL 60950.
• Do not connect your serial cable directly to the projector’s RS-232 serial
interface. Use the extended control panel’s (ECP’s) RS-232 serial
interface only.
• In a location over 6000' (1829 m) altitude, the air is thin and cooling efficiency
is reduced, so use the projector with the fan mode set to High.
• Do not block the projector’s ventilation slots and openings.
• Avoid turning off the projector during the lamp ignition phase since this may
lead to premature lamp failure. Keep the projector lamp on for a minimum
of 15 minutes before turning it off to preserve the lamp life.
• Cycling power to the projector repeatedly can lock or damage your interactive
whiteboard system. After you turn off the system, wait at least 15 minutes
for cooling before starting the system again.
• Before you clean the UF55/UF55w projector, press the power button twice
on the ECP or remote to put the system into Idle mode, and then allow the
bulb to cool for 30 minutes.
• Do not allow liquids or commercial solvents of any kind to flow into the
projector base or head. Do not use spray cleaners or solvents near any part
of the projector since they may damage or stain the unit.

vi | INTRODUCTION – IMPORTANT INFORMATION
IMPORTANT
• Use the instructions that are in the UF55/UF55w projector boxes to install
your system. Do not use the instructions in your SMART Board interactive
whiteboard product box.
• Do not set up or use your interactive whiteboard system in an area
with excessive levels of dust, dirt, humidity or smoke.
• Do not place your interactive whiteboard system near any appliance that
generates a strong magnetic field.
• Do not place your interactive whiteboard system in direct sunlight.
• The screws that secure your interactive whiteboard to the wall are located
directly behind the pen tray. The pen tray must be removed before you can
remove your interactive whiteboard. When you secure the pen tray, you also
secure your interactive whiteboard.
• Using the UF55/UF55w projector system near a TV or radio may cause
interference to the images or sound. If this happens, move the TV or radio
away from the projector.
• Your SMART Board 600i3 or SBD600i3 interactive whiteboard system does
not include speakers. To play audio, connect an audio system to the
projector’s audio output. Consult your authorized SMART reseller
to determine your audio output options.
• If you have peripheral devices that do not use a 4-pin mini-DIN connector or
an RCA composite video jack, or if your device has an audio connection that
does not use RCA jacks, you may need to purchase third-party adapters.
• When cleaning your interactive whiteboard system:
– Wipe the exterior of the projector using a lint-free cloth.
– If necessary, use a soft cloth moistened with a mild detergent to clean the
projector housing.
– Do not use abrasive cleaners, waxes or solvents.
• Disconnect the product from its power source when it’s not used for a
long period.
• If your interactive whiteboard system requires replacement parts, make sure
that the service technician uses replacement parts specified by SMART
Technologies, or parts with the same characteristics as the original.

Contents
Important Information ..............................................................................................i
Read This Section First ....................................................................................i
Safety Warnings, Cautions and Important Information ....................................ii
1About Your SMART Board 600i3 or SBD600i3 Interactive Whiteboard System... 1
SMART Board 600i3 or SBD600i3 Interactive Whiteboard System Features 2
Interactive Whiteboard Features .............................................................. 2
UF55/UF55w Projector System Features................................................. 3
ECP and Cable ........................................................................................ 4
Standard Accessories..................................................................................... 5
Remote Control ........................................................................................ 5
Pen Tray Tools ......................................................................................... 5
Eraser....................................................................................................... 5
Optional Accessories ...................................................................................... 6
SMART Board Audio (SBA) USB Speakers............................................. 6
Wireless Bluetooth® Connection (WC6) .................................................. 6
Active USB Extension Cables (USB-XT).................................................. 6
Cat 5 to USB Cable Extender (CAT5-XT) ................................................ 6
Serial Conversion Module (RS-232)......................................................... 6
GoWire™ SMART Notebook Software
Auto-launch Cable (USB-GW).................................................................. 7
2Installing Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System ............................................................................. 9
Environmental Requirements ....................................................................... 10
Before Installing Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System..................................................................... 12
Recommended Mounting Heights .......................................................... 12

viii | CONTENTS
After Installing Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System..................................................................... 13
Adjusting Keystone Alignment ............................................................... 13
Focusing the Image................................................................................ 14
Performing an Image Alignment............................................................. 15
Securing the Pen Tray and Interactive Whiteboard................................ 19
3Connecting Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System ........................................................................... 21
Installing SMART Software........................................................................... 22
Connecting the Cables to the UF55/UF55w Projector.................................. 23
Routing the Cables................................................................................. 23
Connecting Your Guest Computer to the ECP’s Inputs ......................... 27
Connecting Peripheral Visual or Audio-Visual Devices ................................ 28
4Using Your SMART Board 600i3 or SBD600i3 Interactive Whiteboard System . 29
Turning the System On and Off and Selecting an Input ............................... 30
Using Your Interactive Whiteboard ............................................................... 30
Using Your UF55/UF55w Projector .............................................................. 31
Using Your Remote Control ................................................................... 31
Menu Options......................................................................................... 31
5Remotely Managing Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System ........................................................................... 35
Connecting Your Room Control System to the ECP .................................... 36
Pin Configuration on the ECP RS-232 Connector.................................. 36
Serial Interface Settings ......................................................................... 36
UF55/UF55w Programming Commands....................................................... 38
Powerstate Controls............................................................................... 38
Command Inventory............................................................................... 38
Powerstate Control................................................................................. 40
Source Selection .................................................................................... 41
Video Control ......................................................................................... 41

ix | CONTENTS
Audio Control ......................................................................................... 42
Network Information ............................................................................... 43
System Information ................................................................................ 44
6Troubleshooting Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System ........................................................................... 45
System Warning Lights................................................................................. 46
ECP Ready Light and System Status..................................................... 46
Projector Ready Lights and Projector Status ......................................... 46
Errors ............................................................................................................ 47
Temperature Exceeded.......................................................................... 47
Fan Failure ............................................................................................. 47
Color Wheel Failure................................................................................ 48
Lamp Failure .......................................................................................... 48
Ready Light Isn’t Lit................................................................................ 48
Interactive Whiteboard Indicators and Controls............................................ 49
7Maintaining Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System ........................................................................... 51
Preventing Damage to Your Interactive Whiteboard .................................... 52
Keeping the Writing Surface Clean............................................................... 52
Removing Permanent Marker Ink Stains................................................ 53
Cleaning the Pen Tray .................................................................................. 53
Cleaning the UF55/UF55w Projector ............................................................ 54
Cleaning the Projector............................................................................ 54
Transporting Your SMART Board 600i3 or SBD600i3
Interactive Whiteboard System..................................................................... 55
Contacting SMART Technical Support ......................................................... 55
Locating Your Projector Serial Number.................................................. 55
8Replacing Your UF55/UF55w Projector Lamp .................................................... 57
Replacing the Projector Lamp ...................................................................... 57
Removing the Projector from the Boom ................................................. 59

x| CONTENTS
Replacing the Projector Lamp Module ................................................... 61
Replacing the Projector .......................................................................... 63
Resetting the Lamp Timer...................................................................... 64
ACustomer Support ............................................................................................... 65
Online Information and Support.................................................................... 65
Training......................................................................................................... 65
Technical Support......................................................................................... 65
Shipping and Repair Status .......................................................................... 65
General Inquiries .......................................................................................... 66
Warranty ....................................................................................................... 66
Registration................................................................................................... 66
BHardware Environmental Compliance................................................................. 67
Waste Electrical and Electronic Equipment Regulations (WEEE Directive) . 67
Restriction of Certain Hazardous Substances (RoHS Directive) .................. 67
Batteries........................................................................................................ 67
Packaging ..................................................................................................... 68
Covered Electronics Devices........................................................................ 68
China’s Electronic Information Products Regulations................................... 68
U.S. Consumer Product Safety Improvement Act ........................................ 68
Index ................................................................................................................... 69

Chapter 1
About Your SMART Board
600i3 or SBD600i3
Interactive Whiteboard
System
Your SMART Board 600i3 or SBD600i3 interactive whiteboard system combines
the UF55/UF55w wall-mounted, short-throw projector system with a SMART Board
600 or SBD600 series interactive whiteboard.
Refer to these topics to learn more about the features and accessories that you can
use with your SMART Board 600i3 or SBD600i3 interactive whiteboard system.
SMART Board 600i3 or SBD600i3 Interactive Whiteboard System Features 2
Interactive Whiteboard Features .............................................................. 2
UF55/UF55w Projector System Features................................................. 3
ECP and Cable ........................................................................................ 4
Standard Accessories..................................................................................... 5
Remote Control ........................................................................................ 5
Pen Tray Tools ......................................................................................... 5
Eraser....................................................................................................... 5
Optional Accessories ...................................................................................... 6
SMART Board Audio (SBA) USB Speakers............................................. 6
Wireless Bluetooth Connection (WC6)..................................................... 6
Active USB Extension Cables (USB-XT).................................................. 6
Cat 5 to USB Cable Extender (CAT5-XT) ................................................ 6
Serial Conversion Module (RS-232)......................................................... 6
GoWire SMART Notebook Software Auto-launch Cable (USB-GW) ....... 7

2 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM
SMART Board 600i3 or SBD600i3
Interactive Whiteboard System Features
Your SMART Board 600i3 or SBD600i3
interactive whiteboard system uses the
UF55/UF55w short-throw, high-offset
projector. Although the projector’s basic
operation is the same as in earlier
models, SMART made many
improvements to make the
SMART Board 600i3 or SBD600i3
interactive whiteboard system easier
to install, use, service and upgrade.
When the UF55/UF55w projector
displays an image from your computer on
the touch-sensitive interactive
whiteboard, you can do everything that
you can do at your computer—open and close applications, scroll through files,
conference with others, create new documents or edit existing ones, visit websites,
play video clips and more—by touching the screen. This projector also supports video
and audio connections from a variety of devices, including DVD players, VCRs,
document cameras and digital cameras, and can project media from these sources
onto the interactive screen.
When you use SMART Notebook software with your SMART Board 600i3 or
SBD600i3 interactive whiteboard system, you can write or draw over the projected
computer image in digital ink using a pen tray pen or your finger, and then save these
notes to a SMART Notebook file, or directly into any Ink Aware application.
Interactive Whiteboard Features
Your SMART Board 600 or SBD600
series interactive whiteboard includes
many features of earlier SMART Board
interactive whiteboards, such as a
resistive touch screen and a pen tray.
The SMART Board 600 or SBD600 series
performs best with the UF55/UF55w
projector because of its exceptional color
performance and input response.

3 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM
Other features of your interactive whiteboard include:
• A pen tray that automatically detects which tool you’ve selected when you pick up
a pen or the eraser from the pen tray
• Pen tray buttons that activate the on-screen keyboard, right-click and help
functions
• A durable hard-coated surface that’s tear-proof, optimized for projection,
compatible with dry-erase markers, and easily cleaned with whiteboard cleaner
• A standard USB interface to connect your SMART Board interactive whiteboard to
the host computer
• A security cable lock feature that enables you to lock your interactive whiteboard
to help safeguard it from theft
UF55/UF55w Projector System Features
The UF55/UF55w projector system
includes a short-throw projector for use with
SMART Board 600 or SBD600 series
interactive whiteboards, an extended
control panel (ECP) and a sturdy support
system for classroom environments.
The features of the projector system include:
• A wall-mounted, high-offset SBP-10X (for the XGA or UF55) and SBP-20W
(for the WXGA or UF55w) projector engine that uses DLP® technology by Texas
Instruments™, providing BrilliantColor™ performance and quality Gamma 2.2
correction with High Brightness, Standard and True Color modes
• A safety-oriented design that includes a boom support with a controlled-collapse
feature
• PAL, PAL-N, PAL-M, SECAM, NTSC, NTSC 4.43 video system compatibility
• Composite, S-video, and VESA RGB with additional interface support
for Component YPbPr and Component YCbCr inputs with proper adapters
(not included)
• WXGA, QVGA, VGA, SVGA, XGA, SXGA, SXGA+ and UXGA video format
compatibility
• 1024 × 768 native resolution (UF55)
OR
1280 × 800 native resolution (UF55w)
• Serial RS-232 interface on the ECP for connecting a room control system
• Self-protection timer for a hot re-strike of the projector lamp

4 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM
• Protected cable routing through the projector housing and a cable cover
to prevent tampering and clutter
• A secure mounting and installation system that includes:
– A projector padlock loop
– Mounting hardware for solid masonry or framed wall installations
– Templates and instructions for positioning the system in a safe manner
ECP and Cable
Your interactive whiteboard system’s ECP features connectors for three inputs and
control for four inputs, including the direct HD-DB15 RGB connection to the projector.
Direct inputs supported include:
• A single HD-DB15 (RGB) input connector and
associated audio (3.5 mm jack) for RGB or
component video and HDTV sources
(YPbPr/YCbCr with proper adaptors, not included)
• An S-video (4-pin mini-DIN) and associated audio
(two RCA jacks)
• A composite video (RCA jack) and associated audio (two RCA jacks)
NOTE
A specialized harness cable provided by SMART enables output to the projector.

5 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM
Standard Accessories
The following accessories are included with your SMART Board 600i3 or SBD600i3
interactive whiteboard system.
Remote Control
The remote control enables you to control the system and
set up your UF55/UF55w projector. Use the remote control
to access menu options, system information and input
selection options.
Pen Tray Tools
The pen tray tools include four pens and an eraser.
The pens have rubberized grip areas, colored to match four
colors of digital ink: black, red, green and blue. You can use
dry-erase markers instead of the included pens, as long as
they’re a similar shape, don’t scratch or mark your
interactive whiteboard’s surface and reflect infrared light.
You can use Sanford® EXPO® markers as substitutes.
NOTES
• If the substitute isn’t reflective to infrared light, the pen tray sensors might not
detect the presence of the pen.
• Some of SMART’s older pens aren’t designed to reflect infrared light and the
pen tray sensors might not detect them reliably. Wrap light-colored tape
around a substitute pen to improve the reflection of infrared light, helping
with tool detection.
• Don’t use low-odor dry-erase markers such as Sanford EXPO2, which can be
very difficult to remove. Use standard dry-erase (high-odor) markers that
show a warning to use them only in well-ventilated areas.
Eraser
The eraser resembles a rectangular chalkboard eraser.
Again, you can use a substitute object, as long as it has a
similar shape, doesn’t scratch or mark your interactive
whiteboard’s surface and reflects infrared light.

6 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM
Optional Accessories
For more information about these optional accessories, contact your
authorized SMART reseller.
SMART Board Audio (SBA) USB Speakers
Your interactive whiteboard system requires an audio system
to deliver presentations with sound. The SBA system consists
of a pair of 15-watt, stereo-amplified speakers with a two-port
USB hub and a volume control knob.
Wireless Bluetooth® Connection (WC6)
This accessory eliminates the need for a USB cable between
your computer and interactive whiteboard. The included
7V DC switching power supply provides power to the module
and your interactive whiteboard.
NOTE
This option isn’t available for Dual Touch models SBD680i3 or SBD685i3.
Active USB Extension Cables (USB-XT)
Connect up to four 16' (5 m) active USB extension cables
to extend your interactive whiteboard’s USB connection
to a maximum of 64' (20 m).
Cat 5 to USB Cable Extender (CAT5-XT)
Use the SMART Cat 5 to USB cable extender to extend your
interactive whiteboard’s USB connection up to 120' (36.6 m)
using RJ45 Cat 5 cable (not included). The extender includes
two 6' (1.8 m) USB cables to connect your computer and
interactive whiteboard to the extender units.
Serial Conversion Module (RS-232)
Use the RS-232 module to convert your interactive
whiteboard’s USB connection to a serial connection.
NOTE
This option isn’t available for Dual Touch models SBD680i3 or SBD685i3.

7 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM
GoWire™ SMART Notebook Software
Auto-launch Cable (USB-GW)
The GoWire cable contains SMART Notebook software and
launches it automatically on a guest computer, providing full
access to all interactive whiteboard software tools without
installing SMART Notebook.

8 | CHAPTER 1 – ABOUT YOUR SMART BOARD 600I3 OR SBD600I3 INTERACTIVE
WHITEBOARD SYSTEM