SMART kapp iQ 55 User manual

smarttech.com/docfeedback/170812
USER’S GUIDE
FOR SMARTKAPPiQ™ 55, 65, 65-V2 AND 75 BOARDS

smarttech.com/kb/170812
Product registration
If you register your SMART product, we’ll notify you of new features and software upgrades.
Register online at smarttech.com/registration.
Keep the following information available in case you need to contact SMART Support.
Serial number:
Date of purchase:
この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよ
う要求されることがあります。
VCCI-A
Trademark notice
SMARTamp, SMARTkapp, SMARTkappiQ, PenID, DViT, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of
SMARTTechnologiesULC in the U.S. and/or other countries. Apple, App Store, iPhone, and iPad are trademarks of Apple Inc., registered in the U.S. and other
countries. Google, Google Play, Android and Chrome are trademarks of Google Inc. The Bluetooth word mark is owned by the Bluetooth SIG, Inc. and any use of
such marks by SMARTTechnologiesULC is under license. All other third-party product and company names may be trademarks of their respective owners.
Copyright notice
© 2016SMARTTechnologiesULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or
translated into any language in any form by any means without the prior written consent of SMARTTechnologiesULC. Information in this manual is subject to change
without notice and does not represent a commitment on the part of SMART.
This product and/or use thereof is covered by one or more of the following U.S. patents:
www.smarttech.com/patents
08-2016

i smarttech.com/kb/170812
Important information
WARNING
lFailure to follow the installation instructions shipped with the board could result in injury and
product damage which may not be covered by the warranty.
lDo not open or disassemble the board. You risk electrical shock from the high voltage
inside the casing. Opening the casing also voids the warranty.
lDo not stand (or allow children to stand) on a chair to touch the surface of the board. Rather,
mount the product at the appropriate height.
lTo reduce the risk of fire or electric shock, do not expose the board to rain or moisture.
lIf the board requires replacement parts, make sure the service technician uses replacement
parts specified by SMARTTechnologies or parts with the same characteristics as the
original.
lEnsure that any cables that cross the floor to the board are properly bundled and marked to
avoid a trip hazard.
lDo not insert objects inside the cabinet ventilation holes, because they could touch
dangerous voltage points and cause electric shock, fire or product damage which may not
be covered by the warranty.
lDo not place heavy objects on the power cable. Damage to the cable could cause shock,
fire or product damage which may not be covered by the warranty.
lUseonly extension cords and outlets that can fully accommodate the board’s polarized
plug.
lUse the power cable provided with the board. If a power cable is not supplied, contact your
supplier. Use only power cables that match the AC voltage of the power outlet and that
comply with your country’s safety standards.
lIf the glass is broken, do not touch the liquid crystal. To prevent injury, handle glass
fragments with care when disposing of them.
lDo not move or mount the board by connecting rope or wire to its handles. The board is
heavy, and failure of the rope, wire or handle could lead to injury.
lUse only VESA®-approved mounting hardware.

IMPORTANT INFORMATION
ii smarttech.com/kb/170812
lDisconnect all of the board’s power cables from the wall outlet and seek assistance from
qualified service personnel if any of the following occur:
oThe power cable or plug is damaged
oLiquid is spilled into the board
oObjects fall into the board
oThe board is dropped
oStructural damage, such as cracking, occurs
oThe board behaves unexpectedly when you follow operating instructions
lThe pens on this product use an adhesive containing nonylphenol ethoxylate, a candidate
substance of very high concern under the EU REACH Regulation (EC) 1907/2006.
مﺪﺨﺘﺴﺘمﻼﻗﻷاةدﻮﺟﻮﻤﻟاﻲﻓاﺬﻫﺞﺘﻨﻤﻟاةدﺎﻤﺔﻘﺻﻻيﻮﺘﺤﺘﻰﻠﻋلﻮﻨﻴﻔﻠﻴﻨﻮﻨ،تﻼﻴﺴﻛﻮﺜﻴإﻲﻫوةدﺎﻤﺔﺤﺷﺮﻤنأنﻮﻜﻴﺎﻬﻟةرﻮﻄﺨةﺮﻴﺒﻛﺎًﻘﻓوﺔﺤﺋﻼﻟ
REACH دﺎﺤﺘﻼﻟﻲﺒوروﻷاﻢﻗر (EC)1907/2006.
Las plumas de este producto utilizan un adhesivo que
contiene etoxilato de nonilfenol, una sustancia candidata
de muy alto riesgo según el Reglamento REACH de la UE
(CE) 1907/2006.
Pera na tomto produktu využívají lepidlo obsahující
nonylfenol ethoxylát, což je dle nařízení (ES) REACH
1907/2006 látka vzbuzující mimořádné obavy.
Pennene på dette produkt anvender et klæbemiddel der
indeholder nonylphenolethoxylat, et stof der er særligt
problematiske under EU REACH forordningen (EF)
1907/2006.
Die Stifte dieses Produkts verwenden einen Klebstoff mit
Nonylphenolethoxylat, einem Stoff der nach Artikel 59
der Verordnung (EG) Nr. 1907/2006 (REACH) auf der
Liste der Stoffe mit einem beträchtlichen Risiko steht.
Οι πένες αυτού του προϊόντος χρησιμοποιούν μια
κολλητική ουσία που περιέχει αιθοξυλιω μένη
εννεϋλοφ αινόλη, μια υποψ ήφ ια ουσία που προκαλεί
πολύ μεγάλη ανησυχία σύμφ ω να με τον Κανονισμό
REACH της ΕΕ (ΕΚ) 1907/2006.
Los rotuladores de este producto emplean un adhesivo
que contiene etoxilato de nonilfenol, una sustancia
candidata de gran preocupación según la regulación
REACH de la UE (CE) 1907/2006.
Tämän tuotteen kynissä on liimaa, joka sisältää
nonyylifenolietoksylaattia, joka on erityinen huolenaihe
EU REACH-asetuksen (EY) 1907/2006 mukaan.
이 제품의 펜은 EU REACH Regulation (EC)
1907/2006에 의해 고위험성우려 후보물질로 지정된
노닐페놀 에톡시레이트가 함유된 접착제를 사용합니
다.
Voor de stiften in dit product wordt gebruik gemaakt van
een kleefstof met nonylfenolethoxylaat, een
zeerzorgwekkende stof op dekandidaatslijst volgens de
Europese REACH-richtlijn (EG) 1907/2006.
Pennene som følger med dette produktet bruker et
klebestoff som inneholdernonylfenoloksetylat, et stoff
det er ytret stor bekymring for iEU REACH Regulation
(EC) 1907/2006.
Pióra na tym produkcie używają kleju zawierającego
etoksylan nonylofenolu, substancję z listy kandydackiej
wzbudzającą duże obawy na mocy unijnego
Rozporządzenia REACH (WE) 1907/2006.
As canetas neste produto usam um adesivo contendo
nonilfenol etoxilado, uma substância candidata que
suscita elevada preocupação no âmbito do
regulamento EU REACH (EC) 1907/2006.
В пишущих ручках да нного изде лия исполь зуется
кле й,содержа щий оксиэтилированный нонилф е нол
―кандида т на включе ние в списки особо опасных
ве ще ств в соотве тствии с Ре гламентом ЕС
относитель но пра вил ре гистра ции,оценки,
са нкционирова ния и огра ниче ния использова ния
химиче ских ве ще ств (REACH) 1907/2006.
Pisala na tem izdelku uporabljajo lepilo, ki vsebuje
nonilfenol etoksilat, ki se uvršča med snovi, ki morda
vzbujajo zelo veliko skrb v skladu z Uredbo EU (ES)
1907/2006 REACH.

IMPORTANT INFORMATION
iii smarttech.com/kb/170812
Les crayons de ce produit utilisent un adhésif contenant
des éthoxylates de nonylphénol, substance
extrêmement préoccupante en vertu du règlement
REACH de l'UE (CE) 1907/2006.
Ezen a terméken a tollak egy nonil-fenol-etoxilátot
tartalmazó ragasztót használnak.Ez az anyag az
1907/2006/EK REACH-rendelet értelmében különös
aggodalomra okot adó.
Le penne di questo prodotto utilizzano un adesivo
contenente etossilato di nonilfenolo, una sostanza
candidata estremamente problematica ai sensi del
regolamento REACH dell'UE (CE) 1907/2006.
この製品のペンには、EUのREACH規則（EC）No
1907/2006で定められている高懸念物質候補であるノ
ニルフェノールエトキシレートを含む接着剤が使用
されています。
De inkluderade pennorna för denna produkt använder
ett bindemedel som innehållernonylfenoletoxylat, som
är föremål för bekymmer enligt EU REACH förordning
(EG) 1907/2006.
Bu üründeki kalemler, AB REACH Yönetmeliği(EC)
1907/2006 uyarınca son derece endişe uyandıran
madde adayı nonilfenol etoksilat içeren bir yapıştırıcıyı
kullanmaktadır.
本产品所用之墨笔采用之黏胶含有壬基酚聚氧乙烯醚
（nonylphenol ethoxylate），根据欧盟REACH法规
（EC）1907/2006，此化学物为极受关切化学物名单上
之候选化学物之一。
本產品所用之墨筆採用之黏膠含有壬基酚聚氧乙烯醚
(nonylphenol ethoxylate)，根據歐盟 REACH 法規 (EC)
1907/2006，此化學物為極受關切化學物名單上之候選
化學物之一。
CAUTION
lBefore you clean the board’s screen, shut down or disconnect the computer. Otherwise,
you may scramble the desktop icons or inadvertently activate applications when you wipe
the screen.
lAvoid setting up and using the board in an area with excessive levels of dust, humidity and
smoke.
lDust buildup on the camera windows and reflective tape will degrade touch performance.
SMART recommends that you inspect the camera windows and reflective tape for buildup
and clean weekly.
lMake sure an electrical socket is near the board and remains easily accessible during use.
lThe board should be used only with European TN and TT power distribution systems.
It is not suitable for older, IT-type power distribution systems found in some European
countries. “This system (IT-type) is widely used isolated from earth, in some installations in
France, with impedance to earth, at 230/400V, and in Norway, with voltage limiter, neutral
not distributed, at 230V line-to-line.” (IEC 60950:1999)
Contact qualified personnel if you’re uncertain of the type of power system available where
you’re installing the board.
lThe accessory slot’s maximum available power is 60 W. The slot is not a limited power
source. To reduce the risk of fire, make sure that accessories connecting to the slot satisfy
the fire enclosure requirements of IEC60950-1.

IMPORTANT INFORMATION
iv smarttech.com/kb/170812
lYou must connect the USB cable that came with the board to a computer that has a USB
compliant interface and that bears the USB logo. In addition, the USB source computer must
be compliant with CSA/UL/EN 60950 and bear the CE mark and CSA and/or UL Mark(s) for
CSA/UL 60950. This is for operating safety and to avoid damage to the board.
IMPORTANT
lThe following are the maximum power requirements for the board (including the power
requirements for the accessory slot):
Model Power requirements
SMARTkappiQ™ 55 90V to 240V AC, 50 Hz to 60 Hz, 134 W
SMARTkappiQ 65 100V to 240V AC, 50 Hz to 60 Hz, 199 W
SMARTkappiQ 65-V2 100V to 240V AC, 50 Hz to 60 Hz, 189 W
SMARTkappiQ 75 100V to 240V AC, 50 Hz to 60 Hz, 315 W
lFor additional requirements and other information, refer to the board’s specifications (see
Resources for decision makers on page8).
Federal Communication Commission
interference statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference,and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
lConsult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
5.15–5.25 GHz frequency band operation is restricted to indoor use only. Outdoor operations in the 5150~5250 MHz are
prohibited.

IMPORTANT INFORMATION
v smarttech.com/kb/170812
Radiation exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20 cm between the radiator and your body.
Note: The country code selection is for the non-U.S. model only and is not available to all U.S. models. Per FCC regulations, all
Wi-Fi products marketed in U.S. must be fixed to U.S. operation channels only.
Industry Canada statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son
fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce
dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to
co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the
e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for
point-to-point and non point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e., priority users) of the bands 5250-
5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Avertissement
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions
susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de
réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se
conformer à la limite de p.i.r.e.;
(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de
p.i.r.e.spécifiée pour l’exploitation point à point et non point à point, selon le cas.
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés
utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation exposure statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20 cm between the radiator and your body.
Déclaration d’exposition aux radiations
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

vii smarttech.com/kb/170812
Contents
Important information i
Federal Communication Commission interference statement iv
Industry Canada statement v
Chapter 1: Welcome 1
About this guide 1
About the board 2
About the SMARTkapp app 7
About SMART software 7
Resources for users 8
Resources for others 8
Chapter 2: Starting the board 11
Chapter 3: Connecting a guest computer 13
Connecting a computer to the AM30 appliance 13
Connecting a computer to the board 14
Chapter 4: Connecting to a network 15
Connecting to a Wi-Fi network 15
Connecting to a wired network 15
Chapter 5: Using the launcher 17
Opening the launcher 18
Closing the launcher 18
Adding or removing applications from the launcher 18
Using the Whiteboard 18
Using Activities 21
Using Workspaces 21
Using Browser 22
Using Input 23
Using Screen Share 24
Chapter 6: Troubleshooting 31
What the indicator icons mean 32
Resolving issues with Workspaces 33
Resolving issues with the Browser 33
Resolving issues with Input 33
Resolving Screen Share issues for Apple devices 35
Screen Sharing for Android mobile devices 37

CONTENTS
viii smarttech.com/kb/170812
Screen Sharing for Chrome browser or Chromebook 41
Screen Sharing for Windows computers 43
Appendix A: Installing the AM30 appliance antenna 47
Installing the AM30 appliance antenna 47
Appendix B: Hardware environmental compliance 49
Waste Electrical and Electronic Equipment (WEEE) 49
Batteries 49
More information 49
Index 51

Chapter 1
1 smarttech.com/kb/170812
Chapter 1: Welcome
About this guide 1
About the board 2
Models 2
Specifications 2
Components 2
Screen 3
Cameras and reflective tape channel 3
Front control panel 4
Pens with erasers 5
Presence detection sensor 6
Speakers 6
USB receptacle 6
Accessory slot 6
About the SMARTkapp app 7
About SMART software 7
Resources for users 8
Training 8
Support center and knowledge base 8
Resources for others 8
Resources for decision makers 8
Resources for installers 8
Resources for administrators 9
This chapter introduces SMARTkappiQ boards, the SMARTkapp app and this guide.
About this guide
This guide explains how to use the SMARTkappiQ board and the SMARTkapp app.
This guide is intended for individuals who use boards in their organizations. Other documentation
and resources are available for individuals who install and maintain boards.

CHAPTER 1
WELCOME
2 smarttech.com/kb/170812
About the board
The SMARTkappiQ board features SMART’s proprietary DViT® (Digital Vision Touch) technology
on an LCD screen with e-LED backlight.
Models
Four models of SMARTkappiQ board are available:
lSMARTkappiQ 55
lSMARTkappiQ 65
lSMARTkappiQ 65-V2
lSMARTkappiQ 75
Differences among these models are noted in this guide.
Specifications
Refer to the board’s specifications for detailed technical information, including product dimensions
and weights.
Components
The board consists of the following components:

CHAPTER 1
WELCOME
3 smarttech.com/kb/170812
No. Name More information
Pictured
1 Screen Page3
2 Cameras Page3
3 Reflective tape channel Page3
4 Front control panel Page4
5 Pen with eraser (×2) Page5
6 Presence detection sensor Page6
Not pictured
7 Speakers Page6
8 Connector panel [N/A]
9 Menu control panel [N/A]
10 USB receptacle Page6
11 Accessory slot Page6
Screen
The screen sizes vary by model:
Model Diagonal Width Height Aspect ratio
SMARTkappiQ 55 54 1/2" (138.4 cm) 47 5/8" (121 cm) 26 3/4" (68 cm) 16:9
SMARTkappiQ 65 64 1/2" (163.9 cm) 56 1/4" (142.8 cm) 31 5/8" (80.4 cm) 16:9
SMARTkappiQ 65-V2 64 1/2" (163.9 cm) 56 1/4" (142.8 cm) 31 5/8" (80.4 cm) 16:9
SMARTkappiQ 75 75" (190.5 cm) 65" (165.2 cm) 38 5/8" (93 cm) 16:9
Cameras and reflective tape channel
Cameras in the corners of the screen track finger and pen positions across the display. The screen
is bordered by a channel that contains reflective tape.

CHAPTER 1
WELCOME
4 smarttech.com/kb/170812
CAUTION
lKeep the reflective tape dry.
lDo not remove or damage the reflective tape.
IMPORTANT
lDo not attach adhesive notes or other items to the screen because they will interfere with
the cameras.
lDo not place anything in the reflective tape channel because it will interfere with the
cameras.
Front control panel
The front control panel contains the Standby, Input Select, Mute and volume control buttons.
No. Name
1 Standby button1
2 Input Select button2
3 Mute button3
4 Volume decrease
5 Volume increase
1Press and hold to reset the board
2Change the input source to OPS/HDMI for the kapp iQ experience.
3Press and hold to freeze and unfreeze the screen (SMARTkappiQ 65-V2 and 75 boards only)

CHAPTER 1
WELCOME
5 smarttech.com/kb/170812
IMPORTANT
If there is a film over the front control panel, remove it before using the front control panel.
In normal operation, all buttons are white.
The Standby button also functions as an indicator light:
Indicator light Status Troubleshooting
Solid white Normal operation [N/A]
Off Not receiving power Confirm the board’s power cable is
connected to the power outlet.
Flick the power switch to the ON (I)
position.
Solid amber DPMS (power management)
mode
Press the Standby button to exit
DPMSmode.
Connect an input source.
Slowly flashing
amber
Standby mode Press the Standby button to exit
Standby mode.
If presence detection is enabled, move in
range of the presence detection sensor.
If wake-to-touch is enabled, touch the
screen.
Flashing amber No USB connection from the
connected computer
Verify the connections to the room
computer.
Switch to the room computer’s input
source.
Slowly flashing
white
SMARTBoard service not
running on the connected
computer
Ensure that SMART Product Drivers is
installed and that the SMARTBoard
service is running.4
Pens with erasers
The board comes with two pens with erasers attached.
The board’s bottom frame includes magnetic holders for the pens. Removing a pen from the
holders activates it, and you can use it to draw or erase digital ink.
4This only applies when a computer is connected to the board’s computer connectors.

CHAPTER 1
WELCOME
6 smarttech.com/kb/170812
CAUTION
When you return the pen to the magnetic holder, make sure it’s centered in its holder to keep it
from falling and being damaged.
Presence detection sensor
The board has a presence detection
sensor on its bottom frame that can detect
people up to 16' (5 m) away when the
board is in Standby mode.
When the sensor detects people in the
room, the board turns on. Touching the
screen activates the board. If the room is
empty for a specified period, the board
returns to Standby mode.
Speakers
The board includes two 10 W integrated side-firing speakers.
You or an installer can connect external speakers if desired.
USB receptacle
You can connect a USB drive to update the appliance’s
software.
Accessory slot
Install the AM30 appliance in the accessory slot located on the back of the board to take
advantage of SMARTkappiQ functionality and access SMART education software and third-party
applications.

CHAPTER 1
WELCOME
7 smarttech.com/kb/170812
CAUTION
The accessory slot’s maximum available power is 60 W. The slot is not a limited power source.
To reduce the risk of fire, make sure that accessories connecting to the slot satisfy the fire
enclosure requirements of IEC60950-1.
About the SMARTkapp app
The SMARTkapp app enables users to connect their mobile devices to the board and then do the
following:
lView notes they write on the board on their mobile devices
lSave and export notes
lStart a session and invite others to join and collaborate
To connect Bluetooth-enabled mobile devices to the board, users can scan the Quick Response
(QR) code on the screen. When users first connect their mobile devices, they’re directed to the
Apple App Store (itunes.apple.com/ca/app/smart-kapp/id860144252) or Google Play™ store
(play.google.com/store/apps/details?id=com.smarttech.kapp)to download the SMARTkapp app.
After they download and install the app, they can use it to connect to the board.
About SMART software
To take full advantage of the SMARTkappiQ board’s features, install the following SMART
software on computers connected to the board. Go to SMARTDownloads
(smarttech.com/en/Home+Page/Support/Browse+Support/Download+Software).
Software Description
SMART Product Drivers SMART Product Drivers enables connected computers to detect
input from the board.
SMARTInk™ SMARTInk enables you to write and draw in digital ink over
applications, files, folders, websites and any other open window on
your computer. When you write outside the open windows on your
computer, a SMARTInk Note appears, and you can write inside the
note.
When you open an application that has its own ink tools, you can
use the application’s ink tools to write in the content.

CHAPTER 1
WELCOME
8 smarttech.com/kb/170812
Resources for users
In addition to this guide, SMART provides a variety of other resources for users.
Training
The SMART training website (training.smarttech.com) includes an extensive library of training
resources you can consult as you learn how to use the board.
Support center and knowledge base
The Support center (support.smarttech.com) contains a library of documents, including this guide,
and a knowledge base that you can search when troubleshooting issues.
Resources for others
SMART provides resources for decision makers, installers and administrators as well as users.
Resources for decision makers
Decision makers can refer to the specifications for detailed information about the boards.
Model Specifications
SMARTkappiQ 55 smarttech.com/kb/170840
SMARTkappiQ 65 smarttech.com/kb/170816
SMARTkappiQ 65-V2 smarttech.com/kb/171094
SMARTkappiQ 75 smarttech.com/kb/171001
Resources for installers
Installers can refer to the installation instructions included with the board when installing the
product. PDF versions of these installation instructions are available for download.
Model Installation instructions
SMARTkappiQ 55
SMARTkappiQ 65
smarttech.com/kb/170810
SMARTkappiQ 65-V2 smarttech.com/kb/171107
SMARTkappiQ 75 smarttech.com/kb/170996
Installers should also refer to Considerations for non-standard installations
(smarttech.com/kb/171035).

CHAPTER 1
WELCOME
9 smarttech.com/kb/170812
Resources for administrators
Administrators can refer to the SMARTkappiQ board administrator’s guide for information about
using the board with the SMARTkapp app. A PDF version of this guide is available for download
from smarttech.com/kb/171038.