SMC Networks LFE series User manual

Doc.No.LFE****-OMZ0012
Product Name
Electromagnetic Digital Flow Switch
Remote Type
Model/ Series/ Product Number
LFE#####(Z)
SMC Corporation

-1-
No.LFE****-OMZ0012
Contents
Safety Instructions 2
Model Indication and How to Order 11
Summary of Product Parts 13
Definition and Terminology 14
Mounting and Installation 15
Installation 17
Piping Method 18
Wiring 20
Maintenance and Inspection 22
Troubleshooting 23
Specifications 24
Applicable Fluids and Precautions 25
Characteristics Chart 26
Analogue Output 29
Dimensions 30

-2-
No.LFE****-OMZ0012
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.”
They are all important notes for safety and must be followed in addition to International Standards
(ISO/IEC)*1) , and other safety regulations.
*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.
ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines .(Part 1: General requirements)
ISO 10218: Manipulating industrial robots -Safety.
etc.
Caution
Caution indicates a hazard with a low level of risk which, if not avoided, could result
in minor or moderate injury.
Warning
Warning indicates a hazard with a medium level of risk which, if not avoided, could
result in death or serious injury.
Danger
Danger indicates a hazard with a high level of risk which, if not avoided, will result
in death or serious injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the equipment or
decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
1.The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product precautions
of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is to be
used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to
direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3. An application which could have negative effects on people, property, or animals requiring special safety
analysis.
4.Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective function, and periodical checks to confirm proper operation.

-3-
No.LFE****-OMZ0012
Safety Instructions
Caution
The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited Warranty and Disclaimer/ Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before using the product.
Limited Warranty and Disclaimer
1.The warranty period of the product is 1 year in service or 1.5 years after the product is
delivered,whichever is first.2)
Also, the product may have specified durability, running distance or replacement parts. Please
consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our responsibility,
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and disclaimers
noted in the specified catalog for the particular products.
2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum
pad or failure due to the deterioration of rubber material are not covered by the limited
warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of mass
destruction(WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by the
relevant security laws and regulation of the countries involved in the transaction. Prior to the
shipment of a SMC product to another country, assure that all local rules governing that export
are known and followed.
Caution
SMC products are not intended for use as instruments for legal metrology.
Measurement instruments that SMC manufactures or sells have not been qualified by type approval tests
relevant to the metrology (measurement) laws of each country.
Therefore, SMC products cannot be used for business or certification ordained by the metrology
(measurement) laws of each country.

-4-
No.LFE****-OMZ0012
■Explanation of Symbols
Symbol
Definition
Things you must not do.
Actual instructions are provided as a drawing or sentence close to this mark.
Things you must do
Actual instructions are provided as a drawing or sentence close to this mark.
■Operator
(1) This Operation Manual is intended for those who have knowledge of machinery using pneumatic
equipment, and have sufficient knowledge of assembly, operation and maintenance of such equipment.
Only those persons are allowed to perform assembly, operation and maintenance.
(2) Read and understand this Operation Manual carefully before assembling, operating or providing
maintenance to the product.
■Safety Instructions
Warning
Disassembly
prohibited
Do not disassemble, modify (including the replacement of board) or repair.
Otherwise, an injury or failure can result.
Do not
Do not operate the product outside of the specifications.
Do not use for flammable or harmful fluids.
Fire, malfunction, or damage to the product can result.
Please check the specifications before use.
Do not
Do not use in an atmosphere containing flammable or explosive gases.
Fire or an explosion can result.
The product is not designed to be explosion proof.
Do not
Do not use the product for flammable or highly permeable fluids.
Fire, explosion, breakage or corrosion can result.
Do not
Do not use the product in a place where static electricity is a problem.
Otherwise failure or malfunction of the system can result.
Instruction
If using the product in an interlocking circuit:
- Provide a double interlocking system, for example a mechanical system.
- Check the product for proper operation.
Otherwise malfunction can result, causing an accident.
Instruction
The following instructions must be followed during maintenance:
- Turn off the power supply
- Stop supplying fluid before maintenance.
It may cause an injury.

-5-
No.LFE****-OMZ0012
Caution
Do not touch
Do not touch the terminals and connectors while the power is on.
Otherwise electric shock, malfunction or damage to the switch can result.
Do not touch
Do not touch the piping joint or piping when hot fluid is used.
It may lead to burn.
Check that the piping is cooled down before touching it.
Instruction
■After maintenance is complete, perform appropriate functional inspections and leak
test.
Stop operation if the equipment does not function properly or there is leakage of fluid.
When leakage occurs from parts other than the piping, the product itself may be damaged.
Cut off the power supply and stop the fluid supply.
Do not apply fluid if the system is leaking.
Safety cannot be assured in the case of unexpected malfunction.
■ Handling Precautions
- Follow the instructions given below for selecting and handling.
● The instructions on design and selection (installation, wiring, environment, adjustment, operation,
maintenance, etc.) described below must be followed.
*Product specifications
- Use the specified voltage.
Otherwise failure or malfunction can result.
Insufficient supply voltage may not drive a load due to a voltage drop inside the product.
Check the operating voltage of the load before use.
- Do not exceed the specified maximum allowable load.
This may cause damage or shorten the lifetime of the product.
- Confirm the pressure loss at the sensor according to the flow rate characteristics (pressure loss) graph
before designing piping.
Confirm pressure loss of the sensor from the flow characteristics chart.
- Take care that pressure exceeding the specified range will not be applied due to water hammer.
<Examples of measures for reducing water hammer>
(1) Use a water hammer resistant valve.
(2) Use elastic piping material such as rubber hose etc. and an accumulator to absorb impact pressure.
(3) Shorten the length of piping as much as possible.
- Use the product within the specified operating pressure and temperature range.
- Proof pressure is 2MPa. Proof pressure depends on fluid temperature. Refer to the chart of the
operating pressure range.
- Reserve a space for maintenance.
When designing an application, allow sufficient clearance for maintenance and inspection.

-6-
No.LFE****-OMZ0012
● Product handling
* Mounting
- Tighten to the specified tightening torque.
If the tightening torque is exceeded, the mounting screws, brackets and product may be damaged. Insufficient
torque can cause displacement of the product from its proper position and the looseness of the mounting screws.
- If a commercially available switching power supply is used, be sure to ground the frame ground (FG)
terminal.
- Do not use where the product is subjected to vibration or impact.
Otherwise damage to the internal components may result, causing malfunction.
- When multiple sensors are mounted together in parallel on an installation within the area not suitable for
mounting next to the product, a detected flow rate to fluctuate.
Products should be mounted with a suitable distance between each sensor.
- When piping the product, apply a spanner on the metal part of the piping port to turn the fitting.
Holding other parts of the product with a tool may damage the product.
Specifically, make sure that the spanner does not damage the M12 connector.
This will damage the connector.
- Any dust left in the piping should be flushed out by air before connecting the piping to the product.
Otherwise it can cause damage or malfunction.
- Refer to the flow direction of the fluid indicated on the product label for installation and piping.
- Avoid piping in which the piping size of the IN side of the switch changes suddenly.
If the piping size is reduced suddenly, or there is a restrictor such as a valve on the IN side, the fluid velocity
distribution in the piping will be disturbed, leading to improper measurement. Therefore, the above mentioned
piping reduction or restrictor should be connected on the OUT side.
If the OUT side is opened, or the flow rate is excessive, cavitations may be generated, which may result in
improper measurement. As a measure against this, it is possible to reduce the cavitations by increasing the fluid
pressure.
Take action such as mounting an orifice on the OUT side of the switch, and confirm that there is no malfunction
before handling.
If the orifice of the OUT side is fully closed to operate the pump, the switch may malfunction due to the effect of
pulsation (pressure fluctuation). Ensure that there is no malfunction before use.
- Do not insert metal wires or other foreign matter into the flow path.
This can damage the sensor causing failure or malfunction.
- Never mount the product in a place that will be used as a scaffold during piping.
The product may be damaged if excessive force is applied by stepping or climbing onto it.

-7-
No.LFE****-OMZ0012
- Design and install the product so that fluid always
fills the detection passage.
1. If the detection passage does not become fully
filled with fluid during the use of the product, an
incorrect detection signal can be generated in the
electrodes, prohibiting correct measurement. Be
sure to install the product so that fluid will remain
in the detection passage even after the fluid flow is
stopped.
For vertical mounting, apply fluid from the bottom
to the top. Bubbles may be generated when
applying fluid from the top to the bottom, leading
to operation failure.
(There should not be a problem as long as the
fluid passage is completely filled with fluid)
2. When the product is mounted horizontally, place the cover perpendicular to the floor (to place the electrodes
on the right and the left) to unaffect bubbles.
Fluid passage
Susceptible to bubbles
Not susceptible to bubbles
Above
Down
Down
Cover
Cover
Above
Bubbles
Bubbles
Electrode
Electrode

-8-
No.LFE****-OMZ0012
* Wiring (Including connecting/disconnecting of the connectors)
- Do not pull the lead wire forcefully, or lift the product by the lead wire (Tensile strength 49 N or less).
Hold the product body when handling.
The lead wire will be damaged, leading to failure and malfunction.
Damage to the connector, cover or internal components may result, causing failure or malfunction.
- Avoid repeatedly bending, stretching or applying a heavy object or force to the lead wire.
Repetitive bending stress or tensile stress can cause the sheath of the wire to peel off, or breakage of the wire.
If the lead wire can move, fix it near the body of the product.
The recommended bend radius of the lead wire is 6 times the outside diameter of the sheath, or 33 times the
outside diameter of the insulation material, whichever is larger.
Replace the damaged lead wire with a new one.
- Wire correctly.
Incorrect wiring can cause malfunction or damage the product.
- Do not perform wiring while the power is on.
Otherwise damage to the internal components may result, causing malfunction.
- Do not route wires and cables together with power or high voltage cables.
Route the wires of the product separately from power or high voltage cables to prevent noise and surge from
entering the product.
- Confirm proper insulation of wiring.
Poor insulation (interference with other circuits, poor insulation between terminals etc.) can apply excessive
voltage or current to the product causing damage.
- Design the system to prevent reverse current when the product is performing an operational check.
Depending on the circuit used, which can cause malfunction and damage to the product.
- Keep wiring as short as possible to prevent interference from electromagnetic noise and surge voltage.
Do not use a cable longer than 10 m.
Wire the DC (-) line (blue) as close as possible to the power supply.
- When analogue output is used, install a noise filter (line noise filter, ferrite element, etc.) between the
switch-mode power supply and the product.

-9-
No.LFE****-OMZ0012
Operating environment
- Do not use the product in an environment where the product is constantly exposed to water splashes.
Otherwise failure or malfunction can result. Take measures such as using a cover.
- Do not use in an environment where the product could be exposed to corrosive gas or liquids.
Otherwise damage to the internal parts can result, causing malfunction.
- Do not use the product in a place where the product could be splashed by oil or chemicals.
If the product is to be used in an environment containing oils or chemicals such as oily coolant or cleaning solvent,
even for a short time, it may be adversely affected (damage, malfunction, or hardening of the lead wires).
- Do not use the product with a corrosive fluid or a fluid with an electric conductivity of less than 5μS/cm.
Do not use the product with a fluid which may corrode the fluid contact part or a fluid with a low electric conductivity,
such as pure water or oil.
- Make sue that foreign matter is not allowed in the detection passage.
If a large amount of insulating substances are adhered to the passage, incorrect detection may occur.
If electrically conductive substances are adhered to the internal surface of the detection passage, it may lead to
incorrect detection.
- Do not use in an area where surges are generated.
When there are machines or equipment that generate large surges near the product (magnetic type lifter, high
frequency inductive furnace, motor, etc.), this can result in deterioration and damage of the internal elements. Take
measures against the surge sources, and prevent the lines from coming into close contact.
- Do not use a load which generates surge voltage.
When a surge-generating load such as a relay or solenoid is directly driven, use the product with a surge
absorbing element built-in.
- The product is CE marked, but not immune to lightning strikes. Take measures against lightning strikes
in the system.
- Mount the product in a location that is not affected by vibration or impact.
Failure or malfunction may result.
- Do not use the product in the presence of a magnetic field.
Malfunction can result.
- Do not let foreign matter, such as wire debris, get inside the product.
Failure or malfunction may result.
- Do not use the product in an environment that is exposed to temperature cycle.
Heat cycles other than ordinary changes in temperature can adversely affect the internal components of the
product.
- Do not expose the product to direct sunlight.
If using in a location directly exposed to sunlight, protect the product from the sunlight.
Failure or malfunction may result.
- Keep within the specified operating fluid temperature range and operating temperature range.
The operating fluid temperature range is 0 to 85 °C, and operating temperature range is 0 to 50°C.
If the fluid freezes, it may cause damage and malfunction of the product.
Protection against freezing is necessary.
If the temperature of the fluid is lower than the ambient temperature, condensation will be generated which may
damage the product or cause malfunction.
Avoid abrupt temperature changes even within the specified temperature range.
Failure or malfunction may result.
- Do not use close to a heat source, or in a location exposed to radiant heat.
The heat may cause operation failure.

-10-
No.LFE****-OMZ0012
* Adjustment and Operation
- Check the load status before turning the power supply on.
- Do not short-circuit the load.
Over current may lead to the damage of the product.
- Supply the power when there is no flow.
- There will be a drift on the analogue output for 5 minutes after the power supply is turned on.
- The product doesn’t produce and output signal for 3 seconds after the power is supplied.
* Maintenance
- Confirm safety by turning off the power supplyand stopping the flow before performing maintenance.
There is a risk of unexpected malfunction.
- Perform regular maintenance and inspections.
There is a risk of unexpected failure of components due to the malfunction of equipment and machinery.
- Do not use solvents such as benzene, thinner etc. to clean the product.
This may damage the surface of the body or erase the markings on the body.
Use a soft cloth to remove stains.
For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains
again with a dry cloth.

-11-
No.LFE****-OMZ0012
Model Indication and How to Order
Rated flow range
Symbol
Content
1
0.5～20L/min
2
2.5～100L/min
3
5～200L/min
Port size
Symbol
Port
size
Rated flow range
1
2
3
3
3/8
Yes
-
-
4
1/2
Yes
-
-
6
3/4
-
Yes
-
8
1
-
-
Yes
Thread type
Symbol
Content
Nil
Rc
N
NPT
F
G
Options
Symbol
Lead wire and
M12 connector
Bracket
Nil
Yes
-
1
-
-
2
Yes
Yes
3
-
Yes
Isolation Specifications
Symbol
OUT2
Nil
Not isolated
Z
Isolated
Output Specifications
Symbol
OUT2
J
Analogue 1 to 5V
K
Analogue 4 to 20mA
LFE□□□□□ Z

-12-
No.LFE****-OMZ0012
Combination of options
Options available
Without Lead wire and M12 connector
With Lead wire and M12 connector
Bracket
No
Yes
Accessories/ Part number
If an accessory is required, order using the following part number.
Option
Part No.
Remarks
Weight
Lead wire and M12
connector
LFE-1-A3
Lead wire length: 3 m
Approx. 175 g
Bracket
LFE-1-D
Tapping screw 3 x 10, 4 pcs.
Approx. 45 g
LFE-2-D
Tapping screw 3 x 10, 4 pcs.
Approx. 70 g
LFE-3-D
Tapping screw 3 x 10, 4 pcs.
Approx. 70 g

-13-
No.LFE****-OMZ0012
Summary of Product Parts
Body
Description
Function
Connector
The part to which “Lead wire and M12 connector” are connected.
Lead wire and M12 connector
This is a cable that supplies power to the product and receives output.
Piping port
For piping connections. Connected to the fluid inlet at IN and to the fluid outlet at
Bracket
This is a mounting bracket used to install the product.
Lead wire and M12 connector (4 pins)
(Option)
Connector
Piping port
Piping port
Bracket
(Option)

-14-
No.LFE****-OMZ0012
■Definition and terminology
Term
Meaning
A
Analogue output
Outputs a value proportional to the flow rate. When the analogue output is in the range 1
to 5V, it will vary between 1 to 5V according to the rate of flow.
The same for analogue output of 4 to -20 mA.
Applicable fluids
The fluid(s) that the product can measure.
Attachment
The metal part of both sides of the product to which piping is connected.
C
Cavitation
A phenomenon that may occur in a fluid moving at high speed. In the parts of the fluid
where the pressure is low, vapor bubbles form and then rapidly collapse.
E
Electric conductivity
The electric conductivity is a ratio which shows how easily the electricity flows. The unit
is [S/cm] (siemens/centimeter).
The lower the electric conductivity, the more difficult the electricity flows in the fluid.
On the contrary, the higher the electric conductivity, the easier the electricity flows in the
fluid.Conductivity of tap water is 100 to 200μS/cm.
F
F.S. (full span /
full scale)
This means "full span" or "full scale", and indicates maximum variation width at rated
value. For example, when analogue output is 1 to 5 V, F.S.=5[V] –1[V]=4[V].
(Reference: 1%F.S. = 4[V] × 1% = 0.04[V])
Fluid contact part
A part that comes into physical contact with the fluid.
I
Instantaneous flow
The flow passing per unit of time. If it is 10 L/min, there is a flow of 10 L passing through
the device in 1 minute.
Internal voltage drop
Voltage reduction across an internal device when the switch output is in the ON
condition.
O
Operating fluid
temperature
Range of fluid temperature that can be used by the product.
Operating pressure
range
The pressure range in which the product can be used.
Operating
temperature range
Ambient temperature range in which the product can operate.
P
Pressure
characteristics
Indicates the change in the display value and analogue output when fluid pressure
changes.
Proof pressure
Pressure limit that if exceeded will result in mechanical and/or electrical damage to the
product.
R
Rated flow range
The flow range within which the product will meet all published specifications.
Rated pressure range
The pressure range that satisfies the specifications.
Repeatability
Reproducibility of the display or analogue output value, when the measured quantity is
repeatedly increased and decreased.
Response time
The delay time until the set value reaches 63% in relation to the step input.
T
Temperature
characteristics
Indicates the change in the display value and analogue output caused by ambient
temperature or fluid temperature changes.
W
Water hammer
Water hammer or impact pressure is a pressure surge due to pressure spread when a
fluid in motion is forced to stop or change direction when equipment such as valve, is
opened/closed.

-15-
No.LFE****-OMZ0012
Mounting and Installation
Installation
- Be sure to use the product within the specified operating pressure and temperature range.
- Proof pressure is 2MPa.
Proof pressure depends on fluid temperature. Refer to the chart of the operating pressure range (page 28).
Mounting
- Never mount the switch in a place that will be used as a scaffold.
- Mount the product so that the fluid flows in the direction indicated by the arrow on the side of the body.
- Check the flow characteristics data for pressure loss (page 26) and the straight inlet pipe length effect on
accuracy (page 27), to determine inlet piping requirements.
- Do not suddenly reduce the piping diameter.
- In the non-isolated type, the piping port is connected to the negative terminal of the power supply, and this
product is usable in the negative ground system only.
The positive ground system is not accepted.
- In the isolated type, the piping port is isolated from the power supply, and this product is usable in wiring
connections from the negative and positive ground systems.
Ground connection and wiring method for the non-isolated type (LFE□)
Ground connection and wiring method for the isolated type (LFE□Z)
Positive ground
Negative ground
Power supplay
Piping
24VDC
24VDC
Piping port
Ground(0V)
Isolation
Isolation
Ground(0V)
Ground(0V)
Ground(0V)
Short
Piping port
Piping
Ground(0V)
Ground(-24V)
potential difference
Power supplay
24VDC
24VDC
Positive ground
Negative ground
Ground(0V)
Ground(0V)
Electric

-16-
No.LFE****-OMZ0012
- When multiple sensors are used in parallel, install them at a distance as shown below.
When multiple sensors are mounted in parallel within the area not suitable for installation, the detected flow
rate may fluctuate.
Area not suitable for installation
20mm
20mm
50mm
50mm

-17-
No.LFE****-OMZ0012
■Installation
Bracket mounting
Fix the bracket using the mounting screws (Equivalent to
M4: 4 pcs.).
Bracket thickness is approx. 1.6mm
Refer to the dimensions (page 30) for mouting hole sizes.
Direct mounting
Mount the product with the screw stated below.
Thread type
Nominal
thread size
Tightening
torque
Tapping screw
3
0.7 to 0.8 Nm
Refer to the dimensions (page 30) for the diameter and depth of the mounting screw holes.
If you are installing directly, choose the self tapping screw in depth is to 8mm.
The self tapping screws cannot be reused.
Mounting screw
(4 pcs.)

-18-
No.LFE****-OMZ0012
■Piping Method
When connecting the piping to the product, do not rotate the switch. Apply a spanner to the metal part of the
piping port to turn the fitting.”
Using a spanner on other parts may damage the product.
Specifically, make sure that the spanner does not damage the M12 connector.
This will damage the connector.
Width across flats of attachment
Port size
Width across flats
3/8
24 mm
1/2
28 mm
3/4
35 mm
1
41 mm
Ensure that the piping is tightened to the required torque.
The tightening torque for connection threads is shown in the table below.
Nominal thread size
Appropriate tightening
torque
Rc(NPT)3/8
22 to 24 Nm
Rc(NPT)1/2
28 to 30 Nm
Rc(NPT)3/4
28 to 30 Nm
Rc(NPT)1
36 to 38 Nm
If the tightening torque is exceeded, the product can be damaged. If the tightening torque is insufficient, the
piping may become loose.
The product body is made of resin. Do not apply direct stress, vibration or impact during piping to avoid
malfunction, damage or water leakage. Never mount the product in a location that will be used as a
scaffold.
Affix the piping as close to the product as possible (both before and after the product) to avoid direct stress,
vibration or impact.
If the stress, vibration or impact cannot be reduced, affix the product at multiple locations.
Piping is affixed here
NG
NG
Turn the pipe
Apply a tool

-19-
No.LFE****-OMZ0012
Non-flexible piping materials such as steel piping will be subject to excessive moment load, vibration and
impact from the piping side, so use a flexible tube for intermediate connection.
Misaligned piping may apply long-term load after piping, causing malfunction, damage, or water leakage.
If one-touch fitting is used, hold the fitting by hand so that the load for mounting and removing the tube will
not be applied to the product.
The IN side straight piping length shall be a minimum of 5 times (5D) the piping size to achieve a stable
measurement.
For details, refer to straight piping length and accuracy (page 27).
Avoid any sealing tape getting inside the piping.
Ensure that there is no leakage from loose piping.
Moment load
Flexible piping
Mounting/
removing the tube
Misalignment
Vibration
Tube
Hold by hand
NG