SMITH SYSTEM 55001 User manual

Assembly Instructions
Flowform Soft Seating Line
If you have damaged or missing components,
please contact customer service at 1-800-328-1061
Document #: 179676 REVISED: 03/2023

Hardware and Components
Document #: 179676 REVISED: 03/2023
NYLON & FELT REVERSIBLE GLIDE
QTY. 6
T25 TORX BIT
QTY. 1
#10 X 1-1/8”TORX HEAD
WOOD SCREW
QTY. 6
Special Notes:
•TOOLS REQUIRED:
•Drill w/ T25 Torx driver bit (bit provided)
•Check that all components are accounted for and undamaged before assembling.
•Please assemble the product in a clean and dry area.
•You may need another person to help assemble the product. Team lifting may be
required.
•Clean the product with a mild cleaner and a damp cloth.
•Replacement hardware listed on last page.
(PN: 60135)
NAIL IN GLIDES - NYLON TIP
QTY. 6
NAIL IN GLIDES - FELT TIP
QTY. 6
(PN: 60210)
(PN: 60217)
T25 TORX BIT
QTY. 1
#10 X 1-1/4”TORX FLAT
HEAD WOOD SCREW
QTY. 8
SOFT WALL OUTRIGGER
QTY. 2
(PN: 60052 – Provided with 26” units only)

Glide Marks
Assembly Instructions
Document #: 179676 REVISED: 03/2023
1. Flip the soft seating unit over on to a clean smooth surface that will not harm the
fabric. On the underside of the unit there are marked spots along the perimeter
where the glides should be installed. Due to size, team lifting is advised.
2A.FOR NAIL IN GLIDES: Select the appropriate glides to be installed from the 2 nail in
glide packs that have been provided (i.e. Nylon for carpet, felt for smooth surfaces).
NOTE: Each pack has an extra glide (5+1) provided in case one of the glides is
damaged during installation. Use a hammer to carefully install each glide over the
corresponding mark.
(some units may appear different than reference picture above)
OR

Document #: 179676 REVISED: 03/2023
Nylon Position Felt Position
2B. FOR SCREW IN GLIDES: The glides can be installed either as nylon or felt glides.
Shown on the left is how to install the screw into the glide if you want the nylon side
down, and on the right is how to install the screw if you want the felt side down.
SCREW IN GLIDES (Continued): Install the #10 X 1-1/8” Torx Wood Screw into the glide in
the position you would prefer (nylon or felt) and then install them into the unit in the
marks around the perimeter with the provided T25 Torx Bit.
(some units may appear different than reference picture above)

Document #: 179676 REVISED: 03/2023
4. Flip unit over.
ASSEMBLY COMPLETE
3. FOR 26”H UNITS ONLY: All 26”H units require outriggers to be installed. Identify the 4
marks on the underside of the unit. Position outriggers as shown below and use the
provided T25 Torx bit to install the #10 X 1-1/4” Torx Flat Head Wood Screws.
Outrigger Marks
(some units may appear different than reference picture above)

Replacement Hardware
Document #: 179676 REVISED: 03/2023
[REPLACEMENT HARDWARE PACK: 60175-R]
NYLON & FELT REVERSIBLE GLIDE
QTY. 6
T25 TORX BIT
QTY. 1
#10 X 1-1/8”TORX HEAD
WOOD SCREW
QTY. 6
[REPLACEMENT GLIDE PACK: 60135-R]
T25 TORX BIT
QTY. 1
#10 X 1-1/4”TORX FLAT
HEAD WOOD SCREW
QTY. 8
NAIL IN GLIDES - NYLON TIP
QTY. 6
NAIL IN GLIDES - FELT TIP
QTY. 6
[REPLACEMENT GLIDE PACK: 60210-R]
[REPLACEMENT GLIDE PACK: 60217-R]