SMITH SYSTEM 24000 User manual

(SHOWN MODEL 24000)
MODEL 24001 - RIGHT HAND PED
MODEL 24000 - LEFT HAND PED
02/2008Form #179820
If you have damaged or missing components please contact customer service.
TEACHER DESK - SINGLE DRAWER PED
800-328-1061
www.smithsystem.com

800-328-1061
PARTS LIST
02/2008Form #179820
If you have damaged or missing components please contact customer service.
19183
COLORS:
1
SINGLE PED LEG SET (INCLUDES HDWR AND MODESTY PANEL)
BLA; CMP; PLT
CHOICE OF T-MOLD
CHOICE OF LAMINATE;
68653
1
DESCRIPTION:
QTY PER UNIT:
PART NUMBER:
www.smithsystem.com
DRAWER PEDESTAL
1
19180
BLA; CMP; PLT
DESCRIPTION:
QTY PER UNIT:
PART NUMBER:
COLORS:
30" x 48" TOPDESCRIPTION:
QTY PER UNIT:
PART NUMBER:
COLORS:

02/2008
If you have damaged or missing components please contact customer service.
www.smithsystem.com
1.
Form #179820
THE KEYHOLE-SHAPED SLOTS ARE FACE DOWN.
2. REMOVE THE DRAWER PED FROM THE CARTON. TURN THEM UPSIDE DOWN SO THAT
LAY THE TOP UPSIDE DOWN WITH THE CUT OF THE T-MOLD AT THE BACK. MAKE SURE
FORWARD (TOWARDS YOU).
800-328-1061
FACING UPWARDS.
THE LAMINATE IS FACE DOWN AND THE PRE-ATTACHED MOUNTING PLATES ARE
3. SECURE THE DRAWER PED ON THE MOUNTING PLATE. ALIGN SLOTS ON
DRAWER PED TO KNOBS ON MOUNTING PLATE. BE CAREFUL NOT TO FORCE
THE PARTS TOGETHER. THE KNOBS ON THE PLATE SHOULD COMFORTABLY
ALIGN WITH THE SLOTS. ONCE THE PED IS SEATED ON THE PLATE, SLIDE THE PED
SLIDE FORWARD
T-MOLD CUT
BACK
FRONT
PRE-ATTACHED
PLATE
BACK
FRONT

THIS LEG
HARDWARE INCLUDED
WITH LEG SET
ATTACH LEG TO
DRAWER PED
ATTACH BOLTS HERE
8 PRE-DRILLED
HOLES
www.smithsystem.com
If you have damaged or missing components please contact customer service.
4. ATTACH LEG TO DRAWER PED.
5. ATTACH THE OTHER LEG TO THE TOP USING 8 of the 10 SHEET METAL SCREWS.
02/2008
800-328-1061
Form #179820
MACHINE SCREWS
WOOD SCREWS
HEX KEYS (OR ALLEN WRENCHES)
CONNECTOR BOLTS
CONNECTOR BOLTS
USE THESE FOUR (4)
2.5" SCREWS
WOOD SCREWS

A
ATTACH PANEL TO TOP
USING 2 SHEET METAL SCREWS
SCALE 1 : 4
DETAIL A
NOTCHES SHOULD BE
FACE DOWN
MACHINE SCREWS
SHEET METAL SCREW
BDETAIL B
SCALE 1 : 4 USE THREE (3)
2.5" SCREWS
7. ATTACH LEG TO TOP.
www.smithsystem.com
ATTACH PANEL HERE
INTEGRITY OF THE ASSEMBLY.
TURN THE UNIT OVER (UPRIGHT).
NOTE: USE CAUTION WHEN REPOSITIONING THE UNIT AT ANY TIME. DRAGGING THE DESK
800-328-1061
SCREWS USING AN ELECTRIC DRILL AT THE LOWEST TOQUE SETTING. HEX KEYS
If you have damaged or missing components please contact customer service.
9. WITH THE HELP OF AT LEAST ONE OTHER PERSON, CAREFULLY LIFT THE DESK AND
6. ATTACH THE MODESTY PANEL TO THE LEGS. THEN ATTACH THE PANEL TO THE TOP.
Form #179820 02/2008
ARE PROVIDED TO ASSIST TIGHTENING THE CONNECTOR BOLTS.
ACROSS THE FLOOR OR ROCKING THE DESK ON 2 OF THE 4 LEGS WILL WEAKEN THE
8. THE UNIT IS NOW ASSEMBLED. YOU SHOULD NOT HAVE ANY REMAINING SCREWS
IN THE HARDWARE PACK. TIGHTEN THE MACHINE SCREWS AND THE SHEET METAL