Smithco Spray Star 2000 Quick start guide

Spray Star 2000
Model 20-500-B
TeeJet Spray System
SN: 200G314
January 2021
Product Support: Hwy SS & Poplar Ave; Cameron WI 54822
1-800-891-9435 [e-mail]
Parts & Service

Introduction Service Diagrams Parts Accessories Reference
CONTENTS
Introduction............................................1-3
Introduction........................................................................ 1
General Safe Practices...................................................... 2
Specications ................................................................... 3
Optional Spray Equipment................................................. 3
Service....................................................4-9
Maintenance...................................................................4-6
Storage.............................................................................. 6
Adjustments....................................................................... 7
Service Chart..................................................................8-9
Diagrams ............................................10-15
Wiring Diagram...........................................................10-13
Hydraulic Diagram......................................................14-15
Parts........................................................16-
Body & Frame ............................................................16-17
Nose Cone .................................................................18-21
Linkage.......................................................................20-21
Front Axle .................................................................22-23
Fuel Tank ......................................................................... 24
Oil Tank............................................................................ 25
Seat Panel..................................................................26-27
Engine and Pumps .....................................................28-31
Spray Pump................................................................32-33
Rear Axle....................................................................34-35
Spray Tank..................................................................36-37
Turbo Quad Agitator .................................................. 38-39
15-301 Orbitor ...........................................................40-41
16-998 Hypro®Pump ...................................................... 42
76-197 Gear Pump.......................................................... 43
76-638 Hydrostatic Pump...........................................44-45
43-116 Wheel Motor ...................................................46-47
Accessories .....................................58-111
Plumbing 2002 System (Radion®8140) ....................48-49
Plumbing 2004 System (TeeJet®744) ........................50-51
Wiring 2004 System (TeeJet®744).................................. 52
Wiring 2002 System (Radion®8140) .............................. 53
Plumbing Star Command I & II ................................... 54-55
Star Command I Module Mounts..................................... 56
Star Command I Wiring System ...................................... 57
Star Command II Module Mounts.................................... 58
Star Command II Wiring System ................................... 59
20-785 Regulator Valve ................................................. 61
15-737/14-268 Flanged Strainer...................................... 62
15-743 Manifold Ball Valve .............................................. 63
16-524 Motorized Control Valve ..................................... 64
14-801 Agitation Strainer ................................................. 65
17-580 20’ HD Boom ..................................................66-69
17-580 20’ HD Boom 744 and Radion Plumbing............. 70
17-580 20’ HD Boom Star Command I Plumbing............ 71
17-580 20’ HD Boom Star Command II Plumbing........... 72
17-585 18’ HD Boom Star Command II Plumbing........... 73
17-585 18’ HD Boom ..................................................74-77
17-585 18’ HD 744 and Radion Plumbing ....................... 78
17-585 18’ HD Boom Star Command I Plumbing............ 79
17-601 15’ HD Boom ..................................................80-83
17-601 15’ HD Boom 744 and Radion Plumbing............. 84
17-601 15’ HD Boom Star Command I Plumbing............ 85
17-601 15’ HD Boom Star Command II Plumbing........... 86
Standard Nozzle Assembly.............................................. 87
Star Command I Nozzle Assembly.............................98-89
Star Command II Nozzle Assembly................................. 90
14-515 Water Meter Kit (Gallons).................................... 91
15-618 Water Meter Kit (Liters) ....................................... 91
30-010 Electric Hose Reel .........................................92-94
30-009 Hose Reel ........................................................... 95
Hose Reel Installation.................................................96-97
Hose Reel Adjustments ................................................... 97
30-004 Foam Marker Installation..............................98-101
14-291 Foamer Replacement Parts .......................102-103
20-758 Fresh Water Tank - Front Mount........................ 104
30-006 Fresh Water Tank - Rear Mount ........................ 105
20-503 Chemical Cleanload System ......................106-107
15-620 Chemical Cleanload Replacement Parts....108-109
15-835 Tank Rinsing System........................................ 110
30-350 26Gallon Rinse Tank ..........................................111
Reference .......................................113-114
Decal List....................................................................... 113
Quick Reference Replacement Parts ............................ 114
Warranty ..............................................................................

1
Introduction
INTRODUCTION
Thank you for purchasing a Smithco product.
Read this manual and all other manuals pertaining to the Spray Star 2000 carefully as they contain safety, op-
erating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment
damage.
Keep manuals in a safe place after operator and maintenance personnel have read them. Right and left sides
are from the operator’s seat, facing forward.
All Smithco machines have a Serial Number and Model Number. Both numbers are needed when ordering
parts. Refer to engine manual for placement of engine serial number.
For product and accessory information, help nding a dealer, or to register your procuct please contact us at
www.Smithco.com.
Information needed when ordering replacement parts:
1. Model Number of machine
2. Serial Number of machine
3. Name and Part Number of part
4. Quantity of parts
For easy access record your Serial and Model numbers here.
SMITHCO CUSTOMER SERVICE 1-800-891-9435
 
WARNING
Failure to follow cautious operating practices can re-
sult in serious injury to the operator or other persons.
The owner must understand these instructions, and
must allow only trained persons who understand these
instructions to operate this vehicle.
WARNING:
Engine exhaust and some of its constituents are known
to the State of California to cause cancer, birth defects,
and other reproductive harm.
For more information visit
www.P65Warning.ca.gov

2
Introduction
SAFE PRACTICES
1. It is your responsibility to read this manual and all publications associated with this machine.
2. Never allow anyone to operate or service the machine or its optional equipment without proper training
and instructions. Never allow minors to operate any equipment.
3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before
you operate the equipment. Working with unfamiliar equipment can lead to accidents.
4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,
hands and feet. Operate the machine only in daylight or in good articial light.
5. Inspect the area where the equipment will be used. Pick up all debris you can nd before operating.
Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.
6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other
protective devices in place.
7. Never disconnect or bypass any switch.
8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without
proper ventilation.
9. Fuel is highly ammable, handle with care.
10. Keep engine clean. Allow the engine to cool before storing and always remove the ignition key.
11. Disengage all drives and set park brake before starting the engine.
12. Never use your hands to search for oil leaks. Hydraulic uid under pressure can penetrate the skin and
cause serious injury.
13. This machine demands your attention. To prevent loss of control or tipping of the vehicle:
A. Use extra caution in backing up the vehicle. Ensure area is clear.
B. Do not stop or start suddenly on any slope.
C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.
D. Stay alert for holes in the terrain and other hidden hazards.
14. Before leaving operator’s position:
A. Disengage all drives.
B. Set park brake.
C. Shut engine o󰀨 and remove the ignition key.
D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of
body away from moving parts.
15. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,
adjust or service the machine.
16. Keep the area of operation clear of all bystanders.
17. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.
18. Use parts and materials supplied by Smithco only. Do not modify any function or part.
19. Use caution when booms are down as they extend out beyond the center line of the machine.
20. The tank is a conned space, take precaution.
These machines are intended for professional maintenance on golf courses, sports turf, and any other
area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is
expressed or implied.

3
Introduction
SPECIFICATIONS SPRAY STAR 2000
WEIGHTS and DIMENSIONS
Length 132" (335cm) - w/ booms 137" (348 cm) - w/ Cleanload 151" (384 cm)
Width 72" (183cm)
Height w/ Booms Folded 18' - 110" (279 cm)
Wheel Base 61" (155cm)
Weight Empty 1990 lbs (903 kg)
Weight Loaded 3605 lbs (1635 kg)
SOUND LEVEL (dB)
At ear level 93 dBA
ENGINE
Make Briggs & Stratton
Model# 613477
Type / Spec# 0271-J1
Horsepower 35 hp (26 kW)
Fuel Unleaded 87 Octane Gasoline Minimum
Cooling System Air Cooled
Lubrication System Full Pressure
Alternator 20 Amp
WHEELS & TIRE Front: Two 20 x 10.00 x 10 NHS Multi-Rib; 20 psi (1.4 bar)
Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 18 psi (1.3 bar)
SPEED
Innitely Variable 0-10 m.p.h. (0-16 kph)
BATTERY Automotive type 24F - 12 volt
BCI Group Size 24
Cold Cranking Amps 900 minimum
Ground Terminal Polarity Negative (-)
Maximum Length 10.25" (26 cm)
Maximum Width 6.88" (17 cm)
Maximum Height 10" (25 cm)
FLUID CAPACITY
Crankcase Oil See Engine Manual
Fuel 10 gallon (45,46 liters)
Hydraulic Fluid 5 gallon (19 liters)
Grade of Hydraulic Fluid SAE 10W-40 API Service SJ or higher Motor Oil
OPTIONAL EQUIPMENT
15-618 Water Meter Kit (liters) 14-515 Water Meter Kit (Gallons)
20-503 Chemical Cleanload Safe Fill 15-850 Sunshade Canopy
30-009 Manual Rewind Hose Reel, 200-foot/61-meter capacity
30-010 Electric Rewind Hose Reel, 200-foot/61-meter capacity
30-004 Foam Marker 30-006 Clear water Wash Tank
15-835 Tank Rinsing System 30-350 26 Gal Wash System
17-585 18' HD Super Boom 17-580 20' HD Super Boom
17-590 Lazer-Beam Automatic Boom for HD Booms 31-004 All Weather Top

4
Service
MAINTENANCE
Before servicing or making adjustments to machine, stop engine and remove
key from ignition.
Use all procedures and parts prescribed by the manufacturer's. Read the en-
gine manual before operation.Use No. 2 General purpose lithium base grease
and lubricate every 100
hours. The Spray Star 2000 has 14
grease ttings.
A. One on each pedal mount.
B. Pedal relay.
C. Right and left spindles.
D. All three rod ends.
E. Idler arm.
F. Brake relay.
G. Top and bottom pivot bolts on boom
Electrical Connections
Use dielectric grease on all electrical connections.
Air Cleaner on Engine
1. Unclip the two clips, remove the cover and pull out the element.
2. To service, clean by tapping gently on at surface. Do not oil. Replace if very dirty or damaged.
3. Clean out the inside of the body and cover.
4. Place the element into the body and put the cover back on..
Do not use petroleum solvents, e.g.., kerosene, which will cause cartridge to
deteriorate. Do not use pressurized air to clean cartridge. Pressurized air can
damage cartridge.

5
Service
MAINTENANCE
Engine Oil
Change and add oil according to chart below based on air temperature at the time of operation. Do not over-
ll. Use a high-quality detergent oil classied for service SF, SG, SH. SJ or higher. Use no special additives
with recommended oils. Do not mix oil with gasoline.
SAE Viscosity Grades
1. Use SAE 10W-40 API Service SJ or higher motor oil.
2. For proper warranty, change oil every 500 hours or annually, which ever is rst.
3. Oil level should be 2-2½" (5-6.4cm) from top of the tank when uid is cold. Do not overll.
4. After changing oil, run the machine for a few minutes. Check oil level and for leaks.
5. Always use extreme caution when lling hydraulic oil tank or checking level to keep system free of con-
taminants. Check and service more frequently when operating in extremely cold, hot or dusty conditions.
6. If the natural color of the uid has become black or smells burnt, it is possible that an overheating prob-
lem exists.
7. If uid becomes milky, water contamination may be a problem.
8. If either of the above conditions happen, change oil immediately after uid is cool and nd the cause.
Take uid level readings when the system is cold.
9. In extreme temperatures you can use straight weight oil. We recommend SAE 30W API Service SG
when hot (above 90°F (33°C)) and SAE 10W API Service SJ or higher when cold (below 32°F (0°C)
ambient temperature. Use either motor oil or hydraulic oil, but do not mix.
10. Oil being added to the system must be the same as what is already in the tank. Mark the tank ll area
as to which type you put in.
Tire Pressure
Caution must be used when inating a low tire to recommended pressure.
Over inating can cause tires to explode. Front tires should be 20 psi (1.4bar)
and rear tires should be 18 psi (1.3 bar). Improper ination will reduce tire life
considerably.
Wheel Mounting Procedure
1. Set park brake. Turn machine o󰀨 and remove key.
2. Block wheel on opposite corner.
3. Loosen nuts slightly on wheel to be removed.
4. Jack up machine being careful not to damage underside of machine.
5. Place wheel on hub lining up bolt holes.
6. Torque to 64-74 ft/lb (87-100Nm) using a cross pattern. Re-torque after rst 10 hours and every 200
hours thereafter.
7. Lower machine to ground and remove blocks and jack.

6
Service
MAINTENANCE
Battery
Batteries normally produce explosive gases which can cause personal injury. Do not allow ames, sparks or
any ignited object to come near the battery. When charging or working near battery, always shield your eyes
and always provide proper ventilation. Battery cable should be disconnected before using “Fast Charge”.
Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended
charging rate. If electrolyte starts boiling over, decrease charging.Always remove grounded (-) battery clamp
rst and replace it last. Avoid hazards by:
1. Filling batteries in well-ventilated areas.
2. Wear eye protection and rubber gloves.
3. Avoid breathing fumes when electrolyte is added.
4. Avoid spilling or dripping electrolyte.
Battery Electrolyte is an acidic solution and should be handled with care. If
electrolyte is splashed on any part of your body, ush all contact areas imme-
diately with liberal amounts of water. Get medical attention immediately.
Use of booster battery and jumper cables. Particular care should be used
when connecting a booster battery. Use proper polarity in order to prevent
sparks.
To jump start (negative grounded battery):
1. Shield eyes.
2. Connect ends of one cable to positive (+) termi-
nals of each battery, rst (A) then (B).
3. Connect one end of other cable to negative (-)
terminal of "good" battery (C).
4. Connect other end of cable (D) to engine block
on unit being started (NOT to negative (-) termi-
nal of battery)
To prevent damage to other electrical components on
unit being started, make certain that engine is at idle
speed before disconnecting jumper cables.
STORAGE
If the engine will be out of service for two or more months, use the following storage procedure.
1. Clean the exterior surfaces of the engine.
2. Change the oil and lter while the engine is still warm from operation.
3. The fuel system must be completely emptied, or the gasoline must be treated with a stabilizer to pre-
vent deterioration.
If you choose to use a stabilizer, follow manufacturers recommendations, and add the correct amount
for the capacity of fuel system. Fill fuel tank with clean, fresh gasoline. Run engine for 2-3 minutes to
get stabilized fuel into carburetor. Close fuel shut-o󰀨 valve when unit is being stored or transported.
To empty the system, drain fuel tank and carburetor, or run engine until tank and system are empty.
4. Remove the spark plugs. Add one tablespoon of engine oil into each spark plug hole. Install plugs, but
do not connect the plug leads. Crank the engine two or three revolutions.
5. Store machine in a clean, dry place.

7
Service
ADJUSTMENTS
Wheel Creep
"Creep" is when the engine is running and hydrostatic transmis-
sion is in neutral, but due to inadequate alignment, wheels still
move. Do the following procedure to stop this motion.
1. Lift up and support machine so rear wheels are o󰀨 the
ground and can turn freely.
2. In the engine compartment, the hydrostatic transmission
is on the left side. The shift arm (D) is under the pump and
comes out the side. The idler arm (C) has a bearing that
runs in the notch of the shift arm. Loosen bolt (A).
3. With engine running, move bearing (B) so it centers on the
shift arm (D) and 'wheel creep' stops.
4. Tighten all fasteners and test by using foot pedal linkage to
see that 'creep' is removed.
5. Turn engine o󰀨 and lower machine.
Spray pump with Belt
Located to the right of the engine. The belt should have approximately 1/2" (13mm) of deection in the center
of the top strand. Loosen and tighten the 3/8-16 x 11/4bolts located on the foot of the pump mount.
Master Boom Switch (foot switch)
The master boom switch, located on the left oorboard is used to override the master switch on the computer
console of the spray systems. By pushing down it will turn on/o󰀨 the booms. For the TeeJet System the Mas-
ter Switch on the computer must be on for the master boom control switch to work.
Ground Speed Control (foot Switch)
The ground speed control does not work the same as an automotive type cruise. The ground speed control is
located on the center oorboard and is used to lock forward speed.
To Engage:
1. Flip rocker switch ‘On’ (green light).
2. Obtain desired speed with foot pedal.
3. Step on foot switch to lock speed.
4. Push foot switch again to disengage.
Spray Boss Control (Orange)
Engages and disengages speed boss. Forward is engage and all the way back is disengage. When the lever
is engaged it sets a stop for the accelerator. The accelerator pedal must be used to maintain this speed. To
adjust speed use the knob on the end of the lever, counter clockwise increases speed and clockwise decreas-
es speed. Disengage the lever and you will have full accelerator pedal range.
Tank Agitation
The valve to turn on and o󰀨 the tank agitation is located on the front of the
seat panel, drivers right hand side. Rotate valve handle down to shut o󰀨 and
rotate back up to turn on.

8
Service
SERVICE CHART
Before servicing or making adjustments to the machine, stop engine, block
wheels and remove key from ignition.
Follow all procedures and ONLY use parts prescribed by the manufacturer.
Read the engine manual before maintenance.
The suggested maintenance checklist is not o󰀨ered as a replacement for the manufacturer’s engine manual
but as a supplement. You must adhere to the guidelines established by the manufacturer for warranty cover-
age. In adverse conditions such as dirt, mud or extreme temperatures, maintenance should be more frequent.
Duplicate this page for routine use
Maintenance Check Item For the week of:
Mon Tues. Wed. Thurs. Fri. Sat. Sun.
Check the Safety Seat Switch
Check Steering Operation
Check the fuel level
Check the engine oil level.
Check the condition of the air lter
Clean the engine cooling ns.
Check for unusual engine noises
Check the hydraulic oil level
Check hydraulic hoses and ttings for damage
Check for uid leaks.
Check the tire pressure (18-& 20 psi)
Check the Instrumentation
Inspect electrical system for frayed wires
Check neutral start
Change oil lter.
Change oil.
Lubricate Machine and Booms
Ensure all warning decals are intact.
Areas of Concern
Inspection Performed by:
Item Date Information

9
Service
SERVICE CHART
Item Maintenance Procedure
After the rst 8 operating hours Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))
Change the engine oil lter.
Before each use daily
Check the engine oil level.
Clean area around mu󰀪er and controls.
Check the hydraulic uid level.
Check the tire pressure.
Check condition of hydraulic hoses and ttings.
Check for oil or water leaks.
Proper function of glow lamp timer.
After the rst 50 hours Change Hydraulic Oil Filter.
Change Engine oil and lter.
Every 100 hours
Clean or change air lter.1&2
Clean fuel lter element. 1
Lubricate machine.
Check the battery uid level and cable connections..
Check fan belt tension and damage.
Every 200 hours
Check radiator hoses and clamp bands.
Change engine oil.1
Check idle speed.
Replace oil lter cartridge.1
Change hydraulic oil lter.1
Check air intake line.1
Torque the wheel lug nuts. (64-74 ft/lb (87-100 Nm))
Every 500 hours or yearly Clean Water Jacket and radiator interior.
Replace fan belt.
Every 800 hours Check valve clearance.
Every 1500 hours Check injection nozzle pressure.
Every 3000 hours
Check turbo charger.
Check injection pump.
Check injection timing.
Every 2 years
Change radiator coolant (L.L.C.)
Replace radiator hoses and clamp bands.
Replace fuel hoses and clamps.
Replace intake air lines.
1In dusty conditions or when airborne debris is present, clean more often.
2Replace after every 6 times of cleaning

10
Service
WIRING DIAGRAM
Use dielectric grease on all electrical connections. Color Code Chart
Bl Blue
Br Brown
Y Yellow
G Green
O Orange
R Red
B Black
GY Gray
W White

11
Service
WIRING DIAGRAM
REF# PART# DESCRIPTION QUANTITY
1 20-579 Wire Harness 1
2 13-488 Key Switch 1
3 14-292 Seat Switch 1
4 77-207 Buzzer 1
5 9017 Terminal 2
9018 Seal 2
6 9016 Weather Pack 1
7 33-480 Pressure Switch 1
8 33-084 Magnetic Coil 1
9 33-509 Master Boom Switch 1
10 Right Boom
15-725 Mount Panel End 1
15-727 Rocker - No light 1
15-728 Centering Switch, Momentary, On-O󰀨-On 1
11 Left Boom
15-729 Mount Panel Middle 1
15-728 Centering Switch, Momentary, On-O󰀨-On 1
15-727 Rocker - No light 1
12 Pump
15-729 Mount Panel Middle 1
15-726 Lighted Switch 1
15-731 Rocker - Amber 1
13 Cruise
15-729 Mount Panel Middle 1
15-726 Lighted Switch 1
15-732 Rocker - Green 1
14 Lights
15-725 Mount Panel End 1
15-782 Non-Lighted Switch, On-None-O󰀨 1
15-727 Rocker - No light 1
15 32-014 Lights 2
16 12-804 Hour Meter 1
17 16-998 Spray Pump 1
18 20-733 10AMP Circuit Breaker 1
8877 Red Circuit Breaker Boot 1
19 20-730 GPS Speedometer 1
20 20-730-01 GPS Antenna (part of speedometer) 1
21 48-147 Negative Battery Cable 1
22 33-216 Battery 1
23 50-323 Red Battery Cable 1
24 50-359 Oil Temperature Light 1
25 Solenoid 1
26 77-261 40 Amp Circuit Breaker 1
8977 Red Circuit Breaker Boot 1
27 76-757 Electric Fuel Pump w/ Connectors 1
28 9016 Weather Pack 1
9018 Seals 2
9017 Male Terminal 2
29 76-633 Fuel Pump WIre Harness 1
30 30-042-06 Relay 1

12
Diagrams
HYDRAULIC DIAGRAM

13
Diagrams
HYDRAULIC DIAGRAM PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 43-116 Wheel Motors 2
14-080 Wheel Motor Seal Kit 2
2 15-681 Hose 4
3 20-572 Hydraulic Hose 1
4 20-574 Hydraulic Hose 1
5 8832-29 3/4Suction Hose 1
18-040 Hose Clamp 2
6 15-839 Hydraulic Cylinder 1
14-531 Cylinder Seal Kit 1
7 20-575 Hydraulic Hose 2
8 15-301 Orbitrol 1
15-301-01 Orbitrol Seal Kit 1
9 20-573 Hydraulic Hose 1
10 60-473 Oil Tank 1
11 20-564 Hydraulic Hose 1
12 20-576 Oil Filter Assembly 1
20-576-01 Replacement Filter 1
13 20-563 Hydraulic Hose 1
14 76-638 Hydrostatic Pump 1
77-239-22 Hydrostatic Pump Seal Kit 1
15 76-197 Gear Pump 1
76-197-08 Gear Pump Seal Kit 1
16 15-624 Oil Cooler 1
17 20-570 Hydraulic Hose 1
18 8832-27 3/4 Suction Hose 1
18-040 Hose Clamp 2
19 20-571 Hydraulic Hose 1
PUMP DISPLACEMENT
76-638 Hydrostatic Pump
Displacement Variable to 1.44 in3/R (23.6 cm3/R)
22.44 gpm (84.94 lpm) at 3600 rpm
Max Operating Speed 3600 rpm
Rated Pressure 3000 psi (206.8 bar)
Max Pressure 5000 psi (344.7 bar)
Max Inlet Vacuum 6 in Hg (.203 bar)
Max Inlet Temperature 225°F (107°C)
Max Allowable Case Pressure 25 psi (1.72 bar)
76-197 Gear Pump
Displacement .40 in3/R (6.6 cm3/R) 6.23 gpm (25.39 lpm)
Over tightened ttings will result in crushing the cone which will create a leak.

14
Diagrams
BODY & FRAME DRAWING

Parts
15
BODY & FRAME PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 16-953 16" Lid 1
16-953-01 Gasket for Lid 1
16-169 Strainer Basket 1
2 14-365 Air Gap Filler 1
3 16-961 Adapter 1
4 16-962 Coupler 1
16-962-01 Buna-N Gasket 1
5 20-592 200 Gallon Tank (Fiberglass) 1
20-529 Decal, Spray Star 2000 2
20-593 Decal, Site Gauge 1
6 20-750 Rear Hood (berglass) 1
7 20-611 Roll Bar 1
8 20-780 Roll Bar Base 1
9 31-045 Seat Assembly (Fiberglass) 1
10 14-294 Seat Kit (includes * items) 2
*14-292 Seat Switch 1
*14-800 Seat Rails 1
*HSP-1260-340-250 Seat Spacer 4
11 13-718 Steering Wheel 1
13-726 Center Cap 1
12 76-364 Square Boot 1
76-362 Mini Tilt steering 1
13 20-734 Dash Panel 1
14 31-044 Nose Cone (berglass) 1
15 32-014 Head Light 2
16 20-535 Main Frame 1
17 76-443 Black Handle 3
HSTP-516-18-100 Phillips Machine Screw, 5/16 -18 x 1 6
HNFL-516-18 Flange Whiz-loc Nut, 5/16 -18 6
18 16-857 Front Tire and Wheel 2
16-857-01 Tire, 20 x 10.00 - 10NHS 4-ply 2
42-161-02 Wheel 2
19 76-198-03 Seat Belt 2
20 20-552 Accessory Mount 1
21 16-225 Tire & Wheel 2
16-225-01 Tire, 24 x 13.00 - 12NHS 4 Ply 2
16-225-02 Wheel 2
22 17-615 Boom Support Tube 2
23 16-557 Square Cap 2
24 16-851 1" Nipple 1
25 18-448 1" Ball Valve 1

16
Parts
NOSE CONE DRAWING

Parts
17
NOSE CONE PARTS LIST
REF# PART# DESCRIPTION QUANTITY
1 13-718 15" Steering Wheel 1
2 13-726 Center Cap 1
27-077 Decal, Smithco Round 1
3 76-364 Square Boot 1
4 76-362 Mini Tilt steering 1
5 HB-516-18-150 Hex Bolt, 5/16 - 18 x 11/24
HNFL-516-18 Flange Whiz-loc Nut, 5/16 -18 4
6 15-844 Tilt Steering Spacer 1
7 31-056 Tilt Steering Plate 1
8 31-057 Steering Spacer 1
9 LIGHTS
15-725 Mount Panel End 1
15-727 Rocker, No Light 1
15-782 Non-Lighted Switch, On-None-O󰀨 1
10 CRUISE
15-732 Rocker, Green 1
15-726 Lighted Switch 1
15-729 Mount Panel Middle 1
11 PUMP
15-731 Rocker, Amber 1
15-726 Lighted Switch 1
15-729 Mount Panel Middle 1
12 20-730 GPS Speedometer 1
13 RIGHT BOOM
15-727 Rocker, No Light 1
15-729 Mount Panel Middle 1
15-728 Centering Switch, Momentary On-O󰀨-On 1
14 LEFT BOOM
15-725 Mount Panel End 1
15-727 Rocker, No Light 1
15-728 Centering Switch, Momentary On-O󰀨-On 1
15 50-400 Grommet 1
16 76-443 Black Handle 1
HSTP-516-18-100 Phillips Machine Screw, 5/16 -18 x 1 2
HNFL-516-18 Flange Whiz-loc Nut, 5/16 -18 2
17 HSM-10-32-100 Machine Screw, #10 -32 x 1 17
HNFL-10-32 Flange Whiz-loc Nut, #10 -32 17
18 32-014 Head Light 2
19 20-734 Dash Panel 1
20 20-545 Decal, Dash Panel 1
21 31-044 Nose Cone (berglass) 1
22 HSTP-516-18-150 Phillips Machine Screw, 5/16 -18 x 11/27
HNFL-516-18 Flange Whiz-loc Nut, 5/16 -18 7
23 31-062 Hose Guard 1
24 HB-38-16-125 Hex Bolt, 3/8-16 x 11/41
HNTL-38-16 Nylon Lock Nut, 3/8-16 1
25 31-050 Reverse Pedal 1
26 45-022 Molded Pedal Pad 1
(Continued on next page)

18
Parts
NOSE CONE DRAWING