Smooth Fitness CE-8.0LC User manual

OWNER’S
MANUAL
USER WEIGHT LIMITATION: 400lbs(181kgs)
SERIAL NUMBER (found on frame):_____________________
VERSION: IHP- I
CE-8.0LC

2
SAFETY INSTRUCTIONS
WARNING: Toreduce the risk ofserious injury, read the following Safety Instructions before using the
Elliptical Trainer.
1. Read all warnings posted on the Elliptical Trainer.
2. Read this Owner's Manual and follow it carefully before using the Elliptical Trainer. Make surethat it is properly
assembled and tightened before use.
3. We recommendthat twopeople be available for assembly of this product.
4. Keep children away from the Elliptical Trainer. Do not allow children to use or play on the Elliptical Trainer.Keep
children and pets away from the Elliptical Trainerwhen it is in use.
5. It is recommended that you place this exercise equipment on an equipment mat.
6. Set up and operate the Elliptical Trainer on a solid level surface. Donot position the Elliptical Traineron loose rugs or
uneven surfaces.
7. Inspect the Elliptical Trainerfor worn or loose components prior to use.
8. Tighten/replace any loose or worn components prior to using the Elliptical Trainer.
9. Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint, dizzy, or
experience pain, stop and consult your physician.
10. Follow your physician's recommendations in developing your own personal fitness program.
11. Always choose the workout which best fits your physical strength and flexibility level. Know your limits and train within
them. Always usecommon sense when exercising.
12. Before using this product, please consult your personal physician for a complete physical examination.
13. Do not wear loose or dangling clothing while using the Elliptical Trainer.
14. Never exercise in bare feet or socks; always wear correct footwear, suchas running, walking, or cross-training shoes.
15. Be careful to maintain your balance while using, mounting, dismounting, or assembling the Elliptical Trainer,loss of
balance may result in a fall and serious bodily injury.
16. Keep both feet firmly and securely on the Foot Pedals while exercising.
17. The Elliptical Trainershould not be used by persons weighing over 400 pounds /181 kgs.
18. The Elliptical Trainershould be used by only one person at atime.
19. Use two people to assemble and move the Elliptical Trainer.
20. Maintenance: Replace the defective components immediately and/or keep the equipment out of useuntil repair the
equipment completely.
21. Make sure that adequate space is available for accessto and passage around the Elliptical Trainer;keep at least a
distance of 1 meter from any obstruction object while using the machine.
WARNING: Before starting any exercise or conditioning program you should consult with your personal physician to seeif
you requirea complete physical exam. This is especially important if you are over the age of 35, have never exercised before,
are pregnant, or suffer from any illness.
READ AND FOLLOW THESAFETY PRECAUTIONS. FAILURE TO FOLLOW THESE
INSTRUCTIONS CAN RESULTIN SERIOUS BODILY INJURY

3
HARDWEAR IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts,
or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.
NOTE: The length of all bolts and screws except those with flat heads is measured
from below the head to the end of the bolt or screw. Flat head bolts and
screws are measured from the top of the head to the end of the bolt or screw.
After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware
may be already attached to the part.
Part No. and Description Q’TY
66 Lock Washer (M8) 4
70 Washer (8x38x2.0t) 4
80 Screw, Round Head (M5xp0.8x15mm) 18
81 Screw, Round Head (M5xp0.8x50mm) 2
83 Bolt, Socket Head (M8xp1.25x10mm) 8
90 Bolt, Button Head (M10xp1.5x85mm) 2
94 Bolt, Hex Head (M8xp1.25x65mm) 4
95 Bolt, Hex Head (M10xp1.5x50mm) 2
104 Nylon lock Nut (M10xp1.5) 2
105 Nut Cap 2

4
“BEFORE YOU BEGIN”
Thank you for choosing the CE-8.0LC Elliptical.We take
great pride in producing this quality product and hope it will
provide many hours of quality exercise to make you feel
better, look better and enjoy life to its fullest.
Yes, it's a proven fact that a regular exercise program can
improve your physical and mental health.
Too often, our busy lifestyles limit our time and
opportunity to exercise. The equipment provides a
convenient and simple method to begin your assault on
getting your body in shape and achieving a happier and
healthier lifestyle.
Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.
Read this manual carefully before using the equipment.
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:
MULTI WRENCH TOOL
W/ PHILLIPS
SCREWDRIVER
ALLEN WRENCH
(6 mm)
PHILLIPS
SCREWDRIVER (6mm)
SOCKET WRENCH
(13mm)
T-HANDLE SOCKET
WRENCH (17MM)
Console
Handlebar
Accessory Tray
Main Frame
Front Stabilizer
Leveler
Pedal
Rear Stabilizer
Foam Grip
Upright Post
Pulse Sensor
Plate

5
“ASSEMBLYINSTRUCTIONS”
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials
from your area and place them back into the box. Read each step carefully before beginning.
STEP 1– LevelerAssembly
a. Attach the Levelerx 4(58) to the Front Stabilizer (2) and the Rear
Stabilizer (3).
b. Be sure to tighten the Leveler (58) securely against the Stabilizers(2, 3)
until screw completely tightened as the drawing 1 shown on the top right
corner.
STEP 2– Stabilizer Assembly
Attach the Front Stabilizer (2) and the RearStabilizer(3) onto the Main
Frame (1) and secure with the 4 x Washers (8x38x2.0t) (70), the 4 x Lock
Washers (M8)(66) and the 4 x Hex HeadBolts (M8xp1.25x65mm) (94) with
the socket wrench(13mm) (See picture above)
STEP 3– LevelerAssembly
Tighten one Leveler (58) under the middle of the MainFrame (1).
NOTE: It will be easier to attach the Leveler (58) under the MainFrame (1) by
placing one Styrofoam (or any stationary object) under one side of the Main
Frame (1).
Detailed Lever- drawing 1
Detailed Lever- drawing 2
LEVELING: After placing the
equipment in the intended
location for use, Check the
stabilityof the equipment. If the
equipment is not level,
reviewing the following
direction:
Loosen the Leveler(58) to
make theAdjustment Plate
become lesstight.
Adjust the Leveler (58) for
leveling.
Tighten the Adjustment Plate
securelyagainst the Stabilizer
to lock the Leveler (58) in the
stable position as the drawing
2 shown.
Stabilizer
Adjustment Plate
Leveler(58)
Adjustment Plate
Stabilizer
Leveler(58)
Screwline

6
“ASSEMBLYINSTRUCTIONS”
STEP 4 –Upright Sleeve Assembly
CAUTION: Be careful not to damage the Middle Connection Wire (109) while assembling Step 4 to 6.
Slide the Upright Sleeve (22) onto the Upright Post (4).
Refer to the drawing above. Make sure the direction of the Upright Sleeve (22) is in the correct position.
STEP 5 – Upright Post Assembly
a. Check that 2 x Nylon lock Nuts (M10x8t) (103) have preassembled into the front of the MainFrame (1) as FIG1
illustration shows on the top right corner, making sure that the slotted bracket of the upright post slides between the
nuts and the frame.
b. Insert the Upright Post (4) onto the MainFrame (1) and slightly secure with the 2 x Hex Head
Bolts (M10xp1.5x50mm) (95) by using the T-Handle SOCKET WRENCH(17mm) as shown.
NOTE: Please do not fully tighten Bolts (95) or lock nuts (103) until Step. 7 has
been COMPLETED
STEP 6 – Wire Assembly
Plug the Middle Connection Wire (109) into the Lower Connection Wire (110).
NOTE: Please do not fully
tighten Bolts (95) until Step. 8
for the easy assembly
NOTE: Do not remove the lock
nuts (103) during assembly

7
“ASSEMBLYINSTRUCTIONS”
STEP 7 – Pedal Support Arm
& Pivoting Arm Assembly
a. Attach the Left Pedal Support Arm
(10) onto the Left Pivoting Arm (8)
and secure with the 1x Button Head
Bolt (M10xp1.5x85mm) (90) and 1 x
Nylon lock Nut (M10xp1.5) (104).
b. Press the Nut Cap (105) onto the
Nylon lock Nut (M10xp1.5) (104).
c. Repeat the above procedure to attach
the Right Pedal Support Arm (11)
onto the Right Pivoting Arm (9).
Note: make sure the bolts are fully tightened to avoid noise
STEP 8 – Front Decoration Cover Assembly
a. Please go back to fully tighten with the 2 x
Hex Head Bolts
(M10xp1.5x50mm)
(95) and the 2 x
Lock nuts (103)
with the T-Handle
SOCKET WRENCH
(17mm) as shown.
b. Attach the Front Decorative Upright
Cover (21) onto the front of the Main
Frame (1) with the 2 x Round Head
Screws (M5xp0.8x50mm) (81).
c. Place the Logo Sticker on the surface of the
Front Decorative Upright Cover (21).
A logo sticker is located in one of the
hardware boxes.
d. Slide the Upright Sleeve (22) down to cover the open area of the MainFrame (1).
NOTE: Please make sure Bolts (90) are
inserted from the inside of the Pivoting Arm
and the Nuts (104) and Nut Caps (105) are
installed from the outside

8
“ASSEMBLY INSTRUCTIONS”
STEP 9 – Pedal Assembly
a. Attach the Left Pedal Assembly (33L)
onto the pedal arm plate that is
located in the middle of the Left Pedal
Support Arm (10) and secure with the
4x Socket Head Bolt
(M8xp1.25x10mm) (83).
b. Repeat the above procedure to attach
the Right Pedal Assembly (33R) onto
the Right Pedal Support Arm (11).

9
“ASSEMBLYINSTRUCTIONS”
STEP 10 – Console Bracket
Assembly
CAUTION: Be careful not to
damage the Middle Pulse Sensor Wire
(112) while assembling STEP 9.
Slide the Console Bracket (18) onto the
Upright Post (4) as the FIG1 illustration
shows on the top right corner.
STEP 11– Console Fixed Bracket Assembly
NOTE: For shipping purpose, the4 x Button Head Bolts (M8xp1.25x12mm) (87) and 4 x Lock Washers (M8)(66) are
attached on the Upright Post (4).
a. Remove the 4 x Button Head Bolts (M8xp1.25x12mm)(87) and 4 x Lock Washers (M8)(66) from the Upright Post
(4).
b. Attach the Console Fixed Bracket (43) onto the Upright Post (4) and secure with the 4 x Button Head Bolts
(M8xp1.25x12mm)(87) and 4 x Lock Washers (M8)(66)
STEP 12 – StationaryHandlebar & Wire Assembly
NOTE: For shipping purpose, the Button Head Bolts (M8xp1.25x16mm)(88) and Lock Washers (M8)(66) are attached
on the Stationary Handlebar (5).
a. Remove the 4 x Button Head Bolts (M8xp1.25x16mm)(88) and 4 x Lock Washers (M8)(66) from the Stationary
Handlebar (5).
b. Connect the Middle Pulse Sensor Wire (112) and the Lower Pulse Sensor Wire (113) to the Stationary
Handlebar (5).
c. Insert the Stationary Handlebar (5) into the Upright Post (4) and secure with the 4 x Button
HeadBolts (M8xp1.25x16mm)(88) and 4 x Lock Washers (M8)(66).
NOTE: After connecting the wires’ pins, slightly and gently pull two sides of wires to test and
make sure whether the wires are fully connected.

10
“ASSEMBLYINSTRUCTIONS”
STEP 13 –Wire Assembly
a. Connect the Upper Pulse Sensor Wire (111) to the Middle Pulse Sensor Wire (112).
b. Connect the Upper Connection Wire (108) to the Middle Connection Wire (109).
NOTE: The number of wire pin should be the same for both wires to connect with as the drawing
shown on the right.
STEP 14 –Console & Console Bracket Assembly
a. Place the Console (17) onto the Upright Post (4) and secure with the Round Head Screws (M5xp0.8x15mm) (80).
b. Attach the Console Back Cover (19) to the Console (17) under the Stationary Handlebar (5) and secure with the
Round Head Screws (M5xp0.8x15mm) (80).
c. Slide the Console Bracket (18) onto the Console (17) and secure with the Round Head Screws (M5xp0.8x15mm)
(80).
STEP 15 –Accessory Tray Assembly
NOTE: For shipping purpose, the Round Head Screws (M5xp0.8x15mm) (80) are attached on
the Upright Post (4).
a. Remove the Round Head Screw (M8xp1.25x15mm) (80) from the Upright Post (4).
b. Attach the Accessory Tray (23) onto the Upright Post (4) and secure with the Round
HeadScrew (M5xp0.8x15mm) (80).