Snapmaker CAN Hub A150 User manual

MAKE SOMETHING WONDERFUL
QUICK START GUIDE
A150 | A250 | A350
CAN Hub

Table of Contents
1 Before You Start
1.1 Specifications
1.2 Parts List
1.3 Used Symbols
1.4 Get the Screwdriver Ready
2 Assembly
3 Cable Connection
1
1
2
3
4
5
13

1
1 Before You Start
1.1 Specifications
Dimensions
Weight
Package Weight
Cable Length
Output Ports
The specifications are subject to change without notice.
136 width × 51 depth × 26 height (mm)
0.163 kg
0.7 kg
2000 mm
4

2
1.2 Parts List
Cable × 1
M4 × 10 Hex Socket
Head Screw × 4
M4 × 27 Hex Socket Head
Screw (Customized) × 4
Quick Start Guide × 1 CAN Hub × 1
Conversion Plate × 2
Sliding Nut × 4
Cable Clip × 6
MAKE SOMETHING WONDERFUL
QUICK START GUIDE
CAN Hub
A150 | A250 | A350

3
Failure to follow this instruction might result in malfunction,
damage to the machine or workpiece, or slight personal injury.
Tells you practical advice.
Ensure the highlighted part is facing the right way.
Do not tighten the screws when this symbol appears. Always
tighten the screws when it is absent.
1.3 Used Symbols
Caution
Tip
Direction

4
H2.5
H2.5
H2.5
1.4 Get the Screwdriver Ready
Use the H2.5 bit for machine assembly and other bits for maintenance.
Before use, ensure the screw bit holder is put back into the handle.

5
2 Assembly
This guide takes Snapmaker 2.0 A350 as a demonstration. All steps
demonstrated apply to the assembly and use of the CAN Hub on A150 and
A250. Turn off the machine before assembly.
Insert the Sliding Nuts into the 48CA Beam on the right of the Enclosure.
1
If you are using the A150 Enclosure, you can insert the Sliding Nuts into the 48CA Beam on the left of the
Enclosure.
If you have already installed the Emergency Stop Button, you need to disassemble it before assembling the
CAN Hub. When mounting the hub, ensure there is enough space for the installation of the Emergency Stop
Button.
Sliding Nut ×4

6
Attach the Conversion Plates to the Sliding Nuts. Do not tighten the
screws until Step 4.
M4 × 10 Hex Socket
Head Screw ×4
Conversion Plate ×2
2

7
Adjust the installation position of the Conversion Plates, in accordance
with where the screw holes of the CAN Hub are.
3

8
Tighten the screws of the Conversion Plates.
4

9
M4 × 27 Hex Socket Head
Screw (Customized) ×4
Attach the CAN Hub to the Conversion Plates.
5
CAN Hub ×1

10
Insert one end of the cable into any of the ports of the CAN Hub.
Thread the other end of the cable through the Snap Bushing on the
Back Panel.
6

11
Insert the other end of the cable into either of the Expansion Ports of
the Enclosure Converter.
Do not connect or disconnect any cables when the machine is turned on.
7

12
Lock the cable with Cable Clips, and press the clips into the groove
of the 48CA Beam.
8
Cable Clip ×4

13
3 Cable Connection
If you want to use the Emergency Stop Button and the Air Purifier at the
same time, you can install the Emergency Stop Button in the position as
illustrated. The ports of the CAN Hub can be used as input or output, so you
can insert the cables of these two addons into any of the ports.

Original Instruction
Y.3.B.A.0042-01 V1.0.0