SnapSafe Titan User manual

1
Titan Owner’s Manual

2
Thank you for purchasing a SnapSafe®Titan. Now you
have the peace-of-mind knowing your valuables are
protected from loss due to fire or theft. Best of all, you
can easily locate or relocate this protection anywhere
piece-by-piece to any room in minutes.The SnapSafe®
Modular Assembly System offers all the
impregnability of a welded safe in an easy-to-assemble
modular design.
CUSTOMER SERVICE
______________________________
For all Customer Service questions call toll free:
1-877-214-4470
Or write: SnapSafe Inc. Customer Service
3721 Doubleton Drive, Stuart, FL 34997
Or Email: [email protected]

3
SNAPSAFE TITAN
FEATURES:
_____________________
• Delivered right to your door
• Assembles in minutes
• Sledgehammer and pry-bar resistant
3/16" solid steel door
• Thick steel exterior walls
• 2300°F one-hour Fire Shield
protection
• Heat activated door fire seals
• Secures 12+ long guns
• Nine slot full gun rack
• Option Between UL Security Listed
locks: Digital or Mechanical
• Eight chrome steel live locking bolts
• Spring-loaded relocker
• Powder coated finish
• Lined interior
• Adjustable lined shelves
• Includes 1 full shelf and full gun rack
and a half gun rack with 2 half shelves
• Professional grade “non breach seal”
dead bolt door
• Predrilled for floor mounting
• Lifetime warranty
SNAPSAFE TITAN
SPECIFICATIONS:
__________________
MODEL : Titan
EXTERIOR : 59"H x 22"W x 17 1/2"D
(Add 3" for handle)
INTERIOR : 55 1/8"H x 17"W x 14 1/2"D
DOOR OPENING : 52"H x 14 3/4"W
LOCKING BOLTS : 8
CAPACITY : 12 + Long Guns
WEIGHT : 388 Lbs. - 9 Gauge

4
ASSEMBLING YOUR SNAPSAFE TITAN
1. Unpack and lay out all parts.
2. Thread DOOR HANDLE SPOKES (Part #11) onto the hub on DOOR (Part #12).
3. Install a fresh high-quality 9V battery in the Entry Keypad (see pages 8 and 9).
4. Important – Remove temporary door hinge bolts from door hinges.
5. Enter the factory combination code and open the DOOR, then lift it off the
DOOR FRAME (Part #6) and set aside.
6. AssembleTop, Bottom and Sides (Parts #1 through #4) first.Then bolt the
entire assembly onto the BACK (Part #5).
7. For additional help watch our “Live Action Assembly Video” on the “Features”
page at www.snapsafe.com.
Notes:
1. Each part is marked with an assembly number, orientation and instructions.
2. Each part’s orientation:TOP, BOTTOM, FRONT, etc. matches its orientation in
the assembled vault. LEFT and RIGHT are as you face the front of the vault.
3. For easier assembly, remove the FIRESHIELD blankets from theTOP, BOTTOM
and SIDEWALLS and then stuff them back into place before interior assembly.
4. Screw on nuts loosely at first. Once all Exterior Panels are aligned and
seated tighten the nuts.
5. The INTERIOR SIDE PANELS are designed to fit snuggly. Insert them through
the door opening bottom-to-top and then slide into final position front-to-back.
6. Insert the INTERIOR BOTTOM PANEL through the door opening between
the front and back shelf strips and then drop into position front-to-back.
Door
Frame
Left Side
Top Right Side
Bottom
Back
Top Interior
Panel
Left
Interior
Panel
Right
Interior
Panel
Bottom
Interior Panel
Stand Safe Upright
And Hang Door
Divider Gun Rack
DividerTop
Shelves

5
#5
#2
#7
#18
#8
#9
#14
#10
#3
#12
#1
#17
#16
#6
#11
#4
#13
TITAN PARTS LIST
Part #1 – LEFT SIDE
Part #2 – TOP
Part #3 – RIGHT SIDE
Part #4 – BOTTOM
Part #5 – BACK
Part #6 – DOOR FRAME
Part #7 – TOP INTERIOR PANEL
Part #8 – LEFT INTERIOR PANEL
Part #9 – RIGHT INTERIOR PANEL
Part #10 – BOTTOM INTERIOR PANEL
Part #11 – DOOR HANDLE SPOKES
Part #12 – DOOR
Part #13 – DIVIDER (optional)
Part #14 – GUN RACK DIVIDER TOP (optional)
Part #15 – SHELF HARDWARE (not pictured)
Part #16 – LOWER SHELF (optional)
Part #17 – LOWER SHELF (optional)
Part #18 – UPPER SHELF
Part #19 – HARDWARE (not pictured)
Part #20 – FULL GUN RACK (not pictured)

6
Part #5 – BACK
Part #1
LEFT
Part #3
RIGHT
Part #2 –TOP
Part #4 – BOTTOM
Part #6 – DOOR FRAME Part #12 – DOOR
Part #10
BOTTOM INTERIOR
PANEL
Part #7 –TOP INTERIOR PANEL
Part #8
LEFT INTERIOR
PANEL
Part #9
RIGHT INTERIOR
PANEL
Part #13
DIVIDER
(optional)
Part #16
LOWER
SHELF
(optional)
Part #17
LOWER
SHELF
(optional)
Part #14
GUN RACK DIVIDERTOP
(optional)
Part #18
UPPER SHELF
Part #20
FULL GUN RACK

7
YOUR COMBINATION CODE
• Your factory preset combination code
is 1-2-3-4-5-6.
• It is recorded in a small envelope
wired to the door handle of your vault.
Store this combination in a
location other than your vault.
OPENING AND CLOSING
YOUR VAULT
OPENING:
1. Enter the 6-digit combination code.
2. Rotate 3-spoke handle
clockwise into the open
position and pull door open.
3. The Entry Keypad relocks
in 4 seconds after a valid
code has been entered.
4. The Entry Keypad will return
to“standby” status with a
long beep sound if there is no
operation in 10 seconds after the
system has been activated.
5. If you enter an incorrect
combination 4-times in a row, the
lock will shut down for 5-minutes.
CLOSING:
1. Close vault door.
2. Rotate 3-spoke handle counter-
clock wise to the closed position
until you hear bolts engage.
CHANGING YOUR
COMBINATION CODE
Write down and store a new 6-digit
code. (Do not store in vault).)
You cannot set the combination
code to six (6) zeros (0).
1. Open vault door and lock
it in open position.
2. Enter zero (0) six (6) times. One
beep sounds indicating the
entry is valid and the system
is awaiting a code change.
3. Enter the existing 6-digit
code. One beep sounds,
indicating the entry is valid.
4. Enter a new 6-digit code.
One beep sounds, indicating
the entry is valid.
5. Re-enter the new 6-digit code.
One beep sounds, indicating
that the code in step 4 and
5 are the same and that the
code change is successful.
6. If three beeps sound, the code
change was unsuccessful,
and the existing code is still
valid. Repeat steps 2 – 5.
7. Enter and check new code
3-times before closing door.
Note: Each step in the code change
process must be completed in
10 seconds or the system reverts
back to “standby” status.

8
DOUBLE SAFEGUARDING
VALUABLE PAPERS
Your SnapSafeTitan’s Fire Shield
blankets are rated at 2300ºF for one
hour. However, we recommend that
if you are going to be putting
important papers in
the vault, you first put
it in a fire resistant
document box, and
then put it in the vault.
BOLTING DOWN
YOUR VAULT
We recommend bolting your vault to
the floor using two ¼" wedge anchor
concrete bolts through the predrilled
holes in the BOTTOM of the vault.
LOW BATTERY ALERT
Your lock has a “Low Battery
Alert.” If the Entry Keypad beeps
repeatedly during an unlocking, the
battery is low and needs immediate
replacement.
INSTALLING AND
REPLACING ENTRY
KEYPAD BATTERY
Your vault is equipped with an
electronic lock made with non-volatile
memory, meaning your combination
code is retained even if the batteries
are no longer powering the lock.
If this happens, simply replace the
batteries.
Install only a high-quality alkaline
battery in the compartment in the
back of the Entry Keypad following
these steps.
1. Remove Entry Keypad. Slide it up
and carefully pull it away from the
vault door. (Fig.1)
Note: Do not pull the Keypad as too
much force may damage the cable.
2. Snap new battery into the
connector clip, and slide it into the
battery compartment top down so
that the wires will not be pinched
between the battery and the vault
door. (Fig.2)
3. Fold the connection cable inside
the Keypad (Fig.3)
4. Position the Keypad over the
mounting screws, and slide it down
into position.
Note: Make sure the connection cable
is not trapped between the Keypad
and the door or rubs or tangles on
the mounting screws. (Fig.4)

9

10
CARE AND MAINTENANCE
With a little care and maintenance your SnapSafe Modular Vault will
last a lifetime. Keep the door hinge pins lightly greased so that the
door opens smoothly. Vacuum the inside from time to time, and wipe
down the outside with a soft cloth and mild detergent. Never use
harsh solvents or abrasives on any surfaces, as they may damage the
exterior finish or interior materials.
SNAPSAFE LIFETIME WARRANTY
Were going to take care of you.
Period.
We have built products and a company we are proud of and want you
to be as well.
If you ever experience a fire or attempted break-in we’ll repair or
replace your vault at no charge. (All you have to do is to forward the
report from the proper investigative agency.)

11
NOTES:

IMPORTANT!
Keep forYour Records.
Do not store this booklet and information in your vault.
Date of receipt of vault ______________________
Vault serial number _________________________
(Located on plate on the bottom of door frame)
Customer Service: 3721 Doubleton Drive Stuart, FL 34997
1-877-214-4470 | Email: [e-mail]
SnapSafe®is a Hornady ®Company.
REV 07-2016