socomec ATyS User manual

QUICK START 800 A-3200 A
STEP 1
12
800 A 1000 A 1250 A 1600 A 2000 A 2500 A 3200 A
2x185 - - - - - -
2x50x5 2x63x5 2x63x7 2x100x5
3x100x5 2x100x10 3x100x10
4x185
4x185 4x185 6x185 ---
63 63 63 100 100 100 100
M8 M8 M10 M12 M12 M12 M12
73.46/8.3 73.46/8.3 177.02/20 354.04/40 354.04/40 354.04/40 354.04/40
115.06/13 115.06/13 230.13/26 398.30/45 398.30/45 398.30/45 398.30/45
ATyS / ATyS r
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
- Packaging and contents are in good condition.
- The product reference corresponds to the order.
- Contents should include:
Qty 1 x ATyS / ATyS r
Qty 1 x Emergency handle and fixing clip
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
• This product must always be installed and
commissioned by qualified and approved personnel.
• Maintenance and servicing operations should be
performed by trained and authorised personnel.
• Do not handle any control or power cables connected to
the product when voltage may be, or may become
present on the product, directly through the mains or
indirectly through external circuits.
• Always use an appropriate voltage detection device to
confirm the absence of voltage.
• Ensure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
- For 800 - 3200 A (Uimp = 12 kV). Terminations must respect
a minimum of 14 mm clearance from live parts to parts
intended to be earthed and between poles.
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
In case the product is dropped or damaged in any way it is
recommended to replace the complete product.
Accessories
• Bridging bars and connection kits.
• Control voltage transformer (400 VAC 230 VAC).
• DC power supply (12/24 VDC 230 VAC).
• Phase barriers.
• Terminal shrouds.
• Terminal screens.
• Auxiliary contacts (Additional).
• Padlocking in 3 positions (I - O - II).
• Lockout accessories (RONIS - EL 11 AP).
• Door escutcheon frame.
• ATS controller ATyS C25.
• ATS controller ATyS C55 or C65.
For further details refer to the product instruction manual
under chapter "Spares and Accessories"
www.socomec.com
To download, brochures, catalogues
and technical manuals:
https://www.socomec.com/
operating-instructions_en.html
549614D
Motorised Source Changeover Switch
EN
Installation and Commissioning
STEP 1
Cabinet / Back Plate
Installation
STEP 3
COMMAND /
CONTROL terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
Power SUPPLY
terminal
connections
STEP 5
CHECK
STEP 6A
Control by an external
order (AUTO)
STEP 6C
Padlocking
STEP 6B
Emergency Manual
Operation
STEP 1
Installation
M8 Type Z
M8
Caution: ensure that the
product is installed on a
flat rigid surface.
Recommended
orientation
OK OK
STEP 2
Power Terminal Connections
FRAME B6 FRAME B7 FRAME B8
Minimum cable section Cu (mm2)
Recommended cable section Cu (mm2)
Maximum Cu cable cross-section (mm2)
Maximum Cu busbar width (mm)
Type of screw
Recommended tightening torque(lb.in/N.m)
Maximum tightening torque (lb.in/N.m)
To be connected using terminal lugs, rigid or flexable busbars.
Clip for
storage of
the
emergency
handle

800 A 1000 A 1250 A 1600 A 2000 A 2500 A 3200 A
3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P 3 P 4 P
in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm
C
15.39 391 15.39 391 15.39 391 15.39 391 15.39 391 15.39 391 15.39 391 15.39 391 523 20.59 523 20.59 523 20.59 523 20.59 523 20.59 523 20.59
F 19.84 504 22.99 584 19.84 504 22.99 584 19.84 504 22.99 584 23.46 596 28.19 716 23.46 596 28.19 716 23.46 596 28.19 716 23.46 596 28.19 716
M 10.04 255 13.19 335 10.04 255 13.19 335 10.04 255 13.19 335 13.66 347 18.39 467 13.66 347 18.39 467 13.66 347 18.39 467 13.66 347 18.39 467
T 3.15 80 3.15 80 3.15 80 3.15 80 3.15 80 3.15 80 4.72 120 4.72 120 4.72 120 4.72 120 4.72 120 4.72 120 4.72 120 4.72 120
X 1.87 47.5 1.87 47.5 1.87 47.5 1.87 47.5 1.87 47.5 1.87 47.5 2.09 53 2.09 53 2.11 53,5 2.11 53,5 2.11 53,5 2.11 53,5 2.11 53,5 2.11 53,5
90°
90°
I
II
0
POWER
AUT
Ø 4 ... 8mm
PROG
OK
AUT
READY
TEST ON LOAD
TEST OFF LOAD
ATySg
Un
Auto Conf
5
1
10
14
5
1
10
13
0
1
5
10
20
60
0
1
5
10
20
60
G:
H:
E:
F:
REMOTE CONTROL
A: 3 Ph
B: 1 Ph
C: Neutral
D: Neutral
ATyS
Un N° PP / PN
1: 220 / 127
2: 380 / 220
3: 400 / 230
4: 415 / 240
5: 480 / 277
6: 208 / 120
7: 220 / 127
8: 230 / 132
9: 240 / 138
10: 380 / 220
11: 400 / 230
12: 415 / 240
13: 480 / 277
5
6
7
8
9
10
11
12
13
14
15
16
18
20
1:
2:
3:
4:
5:
6:
7:
8:
9:
10:
11:
12:
13:
14:
3
3
4
4
5
5
6
6
7
7
8
8
9
10
N°: Δ
U Δ F %
XXX
50 Hz60 Hz
XXXXXXXX
Motorised Changeover Switch
1600A Ref : 95054160
AUT
5.43
138
5.91
150
XT
Fix. M
FCC
Fix. 9.84
250
11.02
280
11.02
280
0.83
21
0.83
21
0.35
9
0.49
12.5
0.33
8,5
0.62
15,75
0.62
15,75
0.20
5
0.20
5
0.63x0.43
16x11
ø 0.35
ø 9
ø 0.59
ø 15
0.59
15
ø 0.49
ø 12,5
0.59
15
1.12 28,5
1.12
28,5
0.33
8,5
1.97
50
2.36
60 3.54
90
1.30
33
1.18
30
1.18
30
1.77
45
1.77
45
0.98
25
0.98
25
1.30
33
0.39
10
1250 A
12
3013022
312313 314315 316317 63A64A 24 14 04 13
CONTROL OUTPUTS
1
2
2
1
3
3x
Ø4-8 mm
Contactor logicImpulse logic
order I
position I
order 0
position 0
order II
position II
STEP 6A
Automatic Operation
Ensure that the emergency handle is not
inserted in the product and turn the mode
selector to the AUT position.
LED “Power” Green: ON
LED Manuel/Default: OFF
Non contractual document.
Subject to change without notice.CORPORATE HQ CONTACT: SOCOMEC SAS 1-4 RUE DE WESTHOUSE - 67235 BENFELD, FRANCE - WWW.SOCOMEC.COM
STEP 3
Dimensions in./mm.
800 A to 1000 A
2000 A to 3200 A
800 A to 1600 A
1600 A
to 3200 A
ATyS Voltage
Sensing and
Power supply
Kit excludes the
need for fuses
F1 & F2.
Manual Operation
STEP 6B
Imp. ≥60ms maintened
To enable control, close contact 312 with 317.
To force the product to 0 position/OFF bridge the contact
313 with 317. For contactor logic bridge contact 316
with 317. To operate: close the contact corresponding
to the desired position.
STEP 5
Check
Whilst in manual mode, check
the wiring and if ok power up the
product.
LED “Power” Green: ON
LED Manuel/Defaut Red
(Productnot Available): ON
STEP 4
Ensure that the product is in Manual Mode.
CONTROL / COMMAND Terminals
Power Supply Terminal
Remove the Top cover to access and connect the terminal - Replace the cover before putting in service.
STEP 6C
Padlocking Mode
(as standard : in position O)
Connect the product with a cable of
section of 1,5 to 2,5 mm
2
.
Screw M3 - Tightening torque:
min.: 0.5 Nm - max.: 0.6 Nm
min.: 4.43 lbin - max.: 5.31 lbin