SodaMagic Bubble User manual

1
SodaMagic 'Bubble'
Sparkling Water Machine
Instruction Manual
ENG
SodaMagic

2
Contact
SodaMagic
Room D, 7/F
Hollywood Centre
77-91 Queen's Road West
Sheung Wan
Hong Kong
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
www.SodaMagic.hk

3
Content
Parts and Features
4
Install the CO2 Cylinder
5
How to Use
6
Care and Cleaning
8
Troubleshooting
10
Important Safeguards
11
Guarantee and Registration
12

4
Parts and Features
Thank you for using our product. To properly
understand how to use this product, please read
this instruction manual before use.
What your SodaMagic 'Bubble' can do
The SodaMagic 'Bubble' combines innovative
product design with the latest technology to deliver
one of the world's best compact soda makers.
Carbonate your tap water
Before the first use
With the SodaMagic 'Bubble' you can make
carbonated water, personalized to your taste, in the
comfort of your home.
Hand wash the water bottle in warm soapy water
and rinse. Wipe outside with a soft cloth to dry.
Never wash the water bottle in dishwasher. Harsh
chemicals will damage the water bottle.
The SodaMagic 'Bubble' kit
PET Water Bottle
Sparkling Water Machine
CO2 Cylinder
Scope of Delivery:
The quantity and design of the accessories may differ depending on the Special Offer being promoted.

5
Install the CO2 Cylinder
Note:
Only use SodaMagic CO2 cylinder and water
bottles. Never carbonate if the water bottle is
empty, not completely filled or not fully inserted.
1)
2)
Remove the back cover.
Remove seal and twist off the cap
from the CO2 cylinder.
3)
4)
To install the CO2 cylinder, place a kitchen towel or
soft cloth on the countertop to protect from
scratching. Turn unit upside down and place on top
of towel.
Insert the CO2 cylinder through the opening on
the bottom of the unit. Insert threaded part of the
CO2 cylinder into the unit receptacle and hand-
tighten. Carefully, turn unit right-side up. Put back
the back cover.

6
How to Use
1)
2)
Remove water bottle by turning clockwise to unlock
and pull down to remove from the unit.
Fill water bottle with VERY COLD water to the
MAX fill line.
WARNING! Dried flavor syrups may clog the
carbonation nozzle. Add flavors after carbonation
only.
3)
4)
Insert filled water bottle and turn
counter-clockwise until it can
not be turned.
Press carbonating button to begin carbonation.
Push 2-3 times the carbonating button then stop
when you hear a hissing sound.
Carbonation can be made stronger or lighter by
pressing for more or less time.

7
How to Use
5)
6)
Press the pressure-release button for a few
seconds until all of the excess CO2 is released.
Remove water bottle by turning clockwise to
unlock and pull down to remove from the unit.
7)
Enjoy your sparkling beverage!
Cap and refrigerate the water bottle to preserve the
carbonation of the water.

8
Care and Cleaning
Rinse the water bottle with clean water
after each use.
The water bottle should not be cleaned in
the dishwasher.
The water temperature shall not be higher
than +40° C (+120° F). Use mild detergent
only.
Clean the water bottle carefully and
periodically.
If you do not intend to use the water bottle
any time soon, leave the water bottle open,
letting the inside dry out completely.
To clean the carbonating unit, wipe with a damp cloth.
Do not immerse the carbonating unit in water.
Do not use any solvents or abrasive cleaners, since this could damage the surface.

9
Care and Cleaning
WARNING!!!
Damaged water bottles can fail during carbonation.
Hand wash with soap and warm water. Never place
the water bottle in dishwasher. Never use brushes,
abrasives, or chemical cleaners. Replace water
bottle if it is scratched, deformed or beyond the
expiration date.
Tips for best results
Use the coldest water possible.

10
Troubleshooting
Problem
Solution
No Carbonation
The CO2 cylinder has not been tightly installed. Tighten by
hand. If not, the carbonation button will not activate the CO2
cylinder to release CO2.
Check if the CO2 cylinder is empty. Use a brand new CO2
cylinder.
Fill the water bottle to the MAX Fill Level.
CO2 cylinder is too cold. Wait until CO2 cylinder reaches room
temperature.
Water is too warm. Use very cold water 0.5°-5.5° C (33°-42°
F).
Slight Carbonation
CO2 did not mix well with water. Allow for 10 seconds after
CO2 was released into the water to complete mixing.
CO2 cylinder is close to empty. Use a brand new CO2
cylinder.
The CO2 cylinder is too cold. Wait until the CO2 cylinder
reaches room temperature.
The water is too warm. The colder the water temperature the
higher the carbon dioxide concentration. Use very cold water
0.5°-5.5° C (33°-42° F).
Press on the carbonation button for a longer period of time.
Water overflow from the water bottle
during carbonation
There is too much water in the bottle. Do not fill water bottle
over the suggested water level line.
During the carbonation process small
ice particles are visible
This is normal when you carbonize with very cold water. The
ice particles will disappear soon again.
It is difficult to remove the water
bottle from the carbonating unit after
carbonating.
The excess CO2 has not been released from the water bottle.
Press the pressure-release button until all of the excess CO2
has been released.