SOLTEK SL-65MIV-C User manual

R
The Soul Of Computer Technology
SL-65MIV-C/65MIV2
USER MANUAL V1.2

NOTICE
• Intel, Celeron, Pentium II, Pentium III are trademarks of Intel Corporation.
• VIA, PM133, APOLLO PRO 133, VT 2C694X and VT 2C6 6A are trademarks of VIA
Corporation.
• S3 Savage4 is tademarks of S3 Corporation.
his Users’ Guide & Technical Reference is to help system
manufacturers and end-users set up and install the mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer Inc. is not responsible for print-
ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek Computer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer Inc.
Companies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.
Soltek Computer inc. Provides this manual “As is “ without war-
ranty of any kind, either express or implied, including but not limited
to the implied warranties or conditions of merchantability or fitness
for a particular purpose. In no event shall Soltek Computer inc. be
liable for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con-
sequential damages of any kind, even if Soltek Computer inc. has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright © 2001 So tek Computer Inc. A Rights Reserved.
T
Product Model : SL-65MIV-C / 65MIV2
Manual Revision : V1.2
Release Date : Ma 2001

SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chih, Taipei-
Hsien, Taiwan, R.O.C.
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOUL TECHNOLOGY EUROPE B.V.
Address : Hongkongstraat 55 3047 BR, Rotterdam, The
Netherlands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soultech-europe.com

65MIV-C / 65MIV2
4
C O N T E N T
CHAPTER 1 INTRODUCTION .................................... 8
1- 1 MAINBOARD SPECIFICATION ................................................... 9
1-1-1 CPU ..................................................................................................... 9
1-1-2 CHIPSET ............................................................................................. 9
1-1-3 AWARD BIOS V6.0, SUPPORTING ................................................... 9
1-1-4 EXPANSION SLOTS ........................................................................... 9
1-1-5 ADVANCED HIGH-PERFORMANCE DRAM CONTROLLER ............ 9
1-1-6 MULTI-I/O FUNCTION ........................................................................ 9
1-1-7 INTEGRATED SAVAGE4 2D/3D/VIDEO ACCELERATOR ............... 10
1-1- SOUND CONTROLLER .................................................................... 10
1-1-9 FULL FEATURED ACCELERATED GRAPHICS PORT (AGP)
CONTROLLER .................................................................................. 10
1-1-10 POWER MANAGEMENT ................................................................ 10
1-1-11 FORM FACTOR .............................................................................. 11
1-1-12 HARDWARE MONITORING ........................................................... 11
1-1-13 OTHERS ......................................................................................... 11
1-2 MAINBOARD LAYOUT ............................................................... 12
1-2-1 MAINBOARD LAYOUT --- 65MIV-C .................................................. 12
1-2-2 MAINBOARD LAYOUT --- 65MIV2 ................................................... 13
1-3 CHIPSET DIAGRAM................................................................... 14
1-4 HIGH SCREEN RESOLUTION CRT SUPPORT ........................ 15
1-5 MOTHERBOARD SPECIFICATION TABLE ............................... 16
CHAPTER 2 HARDWARE SETUP............................ 18
2- 1 CPU INSTALLATION ................................................................. 19
2- 2 MEMORY INSTALLATION ......................................................... 20
2- 3 HDD/FDD INSTALLATION ......................................................... 21
2-4 CPU BUS RATIO SELECT ......................................................... 23
2-4-1 BUS FREQUENCY SELECT ............................................................ 23
2- 5 JUMPER SETTING FOR DEVICES ON BOARD: ..................... 24

Content
5
2-5-1 JUMPER JBAT1 FOR CLEARING CMOS DATA: ............................. 24
2-5-2 JP4/JP5 USB PORT SELECT ........................................................... 25
2-5-3 JP9 POWER LOST RESUME ........................................................... 25
2-6 CONNECTORS CONFIGURATIONS ......................................... 26
2-6-1 ONBOARD FAN (JFAN1/JFAN2) ...................................................... 26
2-6-2 CD-ROM AUDIO CONNECTOR (JCD1/JCD2) ................................. 27
2-6-3 WAKE ON LAN FUNCTION (WOL1) ................................................ 27
2-6-4 THERMAL SENSOR CONNECTOR (RT2) -- FOR 65MIV2 ONLY ..... 2
2-6-5 HEADER J2&J3 ............................................................................... 29
2-6-6 CHASSIS PANEL CONNECTOR ...................................................... 33
2-6-7 ATX POWER SUPPLY CONNECTOR .............................................. 34
2-6- PS/2 MOUSE AND PS/2 KEYBOARD .............................................. 34
2-6-9 SECOND USB HEADER (USB2) ...................................................... 35
2-6-10 SERIAL PORT CONNECTOR......................................................... 36
2-6-11 FLAT-PANEL DISPLAY CONNECTOR (DVC1) -- FOR 65MIV2 ONLY .. 37
2-6-12 IRQS DESCRIPTION FOR VARIOUS DEVICES ............................ 3
CHAPTER 3 SOFTWARE SETUP ............................ 41
ABOUT SUPPORT CD ..................................................................... 41
3-1 VIA CHIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ......... 42
3-2 ON BOARD VGA DRIVER INSTALLATION................................ 45
3-2-1 INSTALL PM133 VGA DRIVER FOR WINDOWS 95/9 /9 SE ........ 45
3-2-2 INSTALL PM133 VGA DRIVER FOR WINDOWS NT4.0 ................. 45
3-2-3 INSTALL PM133 VGA DRIVER FOR WINDOWS ME ..................... 46
3-2-4 INSTALL PM133 VGA DRIVER FOR WINDOWS 2000 ................... 47
3-3 AC97 AUDIO CODEC DRIVER INSTALLATION ........................ 4
3-4 HARDWARE MONITOR DRIVER INSTALLATION .................... 50
CHAPTER 4 BIOS SETUP ........................................ 53
THE BIOS ......................................................................................... 53
4-1 WHAT IS BIOS SETUP ............................................................... 54
4-2 HOW TO RUN BIOS SETUP ...................................................... 54
4-3 WHAT IS CMOS ......................................................................... 54

65MIV-C / 65MIV2
6
4-4 WHAT IS POST .......................................................................... 54
4-5 BIOS UPGRADE......................................................................... 54
4-5-1 BEFORE UPGRADING BIOS ........................................................... 55
4-5-2 UPGRADE PROCESS ...................................................................... 55
4-6 BIOS SETUP-- CMOS SETUP UTILITY ..................................... 59
4-6-1 STANDARD CMOS SETUP .............................................................. 60
4-6-2 ADVANCED BIOS FEATURES ......................................................... 63
4-6-3 ADVANCED CHIPSET FEATURES .................................................. 6
4-6-4 INTEGRATED PERIPHERALS ......................................................... 74
4-6-5 POWER MANAGEMENT SETUP ..................................................... 7
4-6-6 PNP / PCI CONFIGURATION ........................................................... 5
4-6-7 SMARTDOC ANTI-BURN SHIELD ...................................................
4-6- FREQUENCY/VOLTAGE CONTROL................................................ 90
4-6-9 LOAD OPTIMIZED DEFAULTS......................................................... 93
4-6-10 SET SUPERVISOR / USER PASSWORD ...................................... 93
4-6-11 SAVE & EXIT SETUP ...................................................................... 94
4-6-12 EXIT WITHOUT SAVING ................................................................ 94
APPENDICES ................................................................. 95
APPENDIX-1 TECHNICAL TERMS INTRODUCTION .................... 96
APPENDIX-2 IDENTIFYING BIOS VERSION AND BIOS PART
NUMBER.................................................................... 97
APPENDIX-3 IDENTIFYING MAINBOARD \ MODEL NUMBER ..... 99

Content
7
Mainboard
Support CD
User’s Manual
Bundled Bonus Pack CD
Bundled Bonus Pack Manual
Temperature Sensor Cable
(for 65MIV2 only)
ATA66/100 IDE Cable
RS232 Cable
FDD Cable
======ITEMLIST CHECKUP

65MIV-C / 65MIV2
8
CHAPTER 1
INTRODUCTION
• This chapter briefly introduces the characteristics of this mainboard. It
includes the information regarding the chipset, CPU types, built-in
functions and layout. Users will have more ideas about mainboards after
reading this chapter.
1-1 MAINBOARD SPECIFICATION
1-2 MAINBOARD LAYOUT
1-3 CHIPSET DIAGRAM
1-4 HIGH SCREEN RESOLUTION CRT SUPPORT
1-5 MOTHERBOARD SPECIFICATION TABLE
THIS CHAPTER CONTAINS THE FOLLOWING TOPICS :

Chapter1 Introduction
9
1- 1 MAINBOARD SPECIFICATION
1-1-1 CPU
• Supporting Intel® FC-PGA370 Pentium® III up to 1GHz.
• Supporting CeleronTM & PPGA370 Celeron processors up to 50MHz.
• Supporting VIA Cyrix III processors up to 00MHz.
• Supporting 66 to 200 MHz system bus speed.
• Supporting processor voltage Auto-Detect circuit.
1-1-2 CHIPSET
• North Bridge - VIA 605 PM133.
• South Bridge - VIA VT 2C6 6A (65MIV-C).
VIA VT 2C6 6B (65MIV2).
1-1-3 AWARD BIOS V6.0, SUPPORTING
• Plug & Play V1.0.
• Flash Memory for easy upgrade.
• Year 2000 compliant.
• BIOS writing protection.
• SMARTDOC ANTI-BURN SHIELD.
• RedStorm Overclocking Tech.
1-1-4 EXPANSION SLOTS
• Three PCI bus Mater slots.
• One AGP 4x mode slot.
• Three DIMM slots.
• One DVC1 slot. (for 65MIV2 only)
1-1-5 ADVANCED HIGH-PERFORMANCE DRAM
CONTROLLER
• Supporting PC133 and PC100 SDRAM and Virtual Channel Memory (VCM)
SDRAM up to 3 DIMMs.
• 64-bit data width and 3.3V DRAM interface.
• Supporting up to 1.5 GB memory space.
• Supporting different DRAM types used in mixed combinations.
• PCI-2.2 compliant, 32 bit 3.3V PCI interface with 5V tolerant inputs .
1-1-6 MULTI-I/O FUNCTION
• Two Ultra DMA 33 / 66 Master Mode PCI EIDE ports. (for 65MIV-C only)
• Two Ultra DMA 33 / 66/100 Master Mode PCI EIDE ports. (for 65MIV2 only)

65MIV-C / 65MIV2
10
• Two UART’s for Complete Serial Ports.
• One dedicated IR connector:
--- A third serial port dedicated to IR function either through the two complete serial
ports or the third dedicated port Infrared-IrDA (HPSIR) and ASK (Amplitude Shift
Keyed) IR.
• Multi-mode parallel connector supporting:
--- Standard mode, ECP and EPP support.
• Floppy Disk connector supporting:
--- Two FDDs with drive swap function.
• Universal Serial Bus connector supporting:
--- USB v1.1 and Intel Universal HCI v1.1 compatible.
--- 2 built-in USB connectors, in addition to one internal USB header which
requires a USB cable to support 2 more optional USB ports.
• PS/2 Keyboard connector.
• PS/2 Mouse connector.
1-1-7 INTEGRATED SAVAGE4 2D/3D/VIDEO ACCELERATOR
• Optimized Share Memory Architecture (SMA).
• 2 to 32MB frame buffer using system memory.
• Single cycle 12 -bit 3D architecture.
• Full AGP 4x, including sideband addressing and execute mode.
• Floating point triangle setup engine.
• M triangles/second setup engine.
• 140M pixels/second trilinear fill rate.
• 2D/3D resolutions up to 1920x1440.
1-1-8 SOUND CONTROLLER
• SoundBlaster Pro Hardware and Direct Sound Ready AC’97 Digital Audio
Controller with Codec Onboard.
1-1-9 FULL FEATURED ACCELERATED GRAPHICS PORT
(AGP) CONTROLLER
• Synchronous and pseudo-synchronous with the host CPU bus with optimal
skew control PCI AGP CPU Mode 33/66/100 MHz DDR 3x synchronous.
• Support 66MHz 1x/2x/4x modes for AD and SBA signaling.
• AGP v2.0 compliant.
1-1-10 POWER MANAGEMENT
• ACPI 1.0 compliant (Advanced Configuration and Power Interface).
• APM V1.2 compliant (Legacy power management).

Chapter1 Introduction
11
• Supporting Wake On LAN (WOL) & Wake On Modem.
• Supporting real time clock (RTC) with date alarm, month alarm, and cen-
tury field.
1-1-11 FORM FACTOR
• ATX form factor, 4 layer PCB.
• Mainboard size: 22.0cm X24.5cm.
1-1-12 HARDWARE MONITORING
• Programmable control, status, to provide monitoring and alarm for flexible
desktop management of hardware temperature. (software included in sup-
port CD)
• 5 positive voltage statuses monitoring.
• 2 fan speeds statuses monitoring.
• 2 temperature statuses monitoring. (for 65MIV2 only)
1-1-13 OTHERS
• Clock generator supporting 1 MHz linear clock setting.

65MIV-C / 65MIV2
12
13 13
JP4 JP5
13
JBAT1
13
JP9
JFAN2
JFAN1
WOL1
JCD1
JCD2
1 4
1 4
AGP 4X
PCI 1
PCI 2
PCI 3
DIMM1 DIMM2 DIMM3
FDD1
IDE2 IDE1
SOCKET 370
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97
Codec
C ock Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
PS/2 MOUSE PS/2 K/B
upper
ower
USB1 USB0
upper
ower
VIA
VT8605
VIA
VT82C
686A
COM2
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
PC100/PC133 SDRAM
1
1
J2 J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
++
--
+-
1 15 1 15
1-2 MAINBOARD LAYOUT
1-2-1 MAINBOARD LAYOUT --- 65MIV-C
• Default Setting: Intel Celeron 300A/66 MHz

Chapter1 Introduction
13
1-2-2 MAINBOARD LAYOUT --- 65MIV2
• Default Setting: Intel Celeron 300A/66 MHz
13 13
JP4 JP5
13
JBAT1
13
JP9
JFAN2
JFAN1
J2 J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
WOL1
JCD1
JCD2
1 4
1 4
AGP 4X
PCI 1
PCI 2
PCI 3
DIMM1 DIMM2 DIMM3
FDD1
IDE2 IDE1
SOCKET 370
RT1
RT2
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97
Codec
C ock Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC PS/2
MOUSE PS/2 K/B
upper
ower
USB1 USB0
upper
ower
VIA
VT8605
VIA
VT82C
686B
COM2
DVC1
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
PC100/PC133 SDRAM
1
1
1
++
--
+-
1 15 1 15

65MIV-C / 65MIV2
14
1-3 CHIPSET DIAGRAM
• The VT 605 is a high performance, cost-effective and energy efficient SMA
chip set for the implementation of AGP / PCI / LPC desktop personal com-
puter system with 66MHz, 100MHz, and 133MHz CPU host bus (“Front
Side Bus”) frequencies and based on 64-bit Socket-370 (Intel Pentium III,
Celeron) super-scalar processors. VT 605 is the VIA part number.
VT8605 System B ock Diagram with VT82C686A
PCI-TO-ISA South Bridge
ATA33/66
4X USB
AGP 4X Expansion
Interface
VT82C
686A
VT8605
SMA NB
552-pin
PBGA
PCI S ots 33MHz,
32-bit PCI
64-bit 133/100/66 MHz
133/100/66 MHz
PC133/PC100 SDRAM
TV
Encoder
TMDS
Xmitter
Socket 370
Ce eron/PIII
CPU
Seria Port
F oppy Disk
Para e Port
EPROM
AC-97
LPC
Integrated
AC-97 Audio
AC-Link
FSB

Chapter1 Introduction
15
1-4 HIGH SCREEN RESOLUTION CRT SUPPORT
Reso ution Supported
System Memory Frame Buffer
Size (8MB Defau t)
640x4 0x /16/ 32 4MB MB 16/32MB
00x600x /16/ 32
1024x76 x /16/ 32
12 0x1024x
12 0x1024x16
12 0x1024x32
1600x1200x
1600x1200x16
1600x1200x32
1920x1440x
1920x1440x16
High Screen Reso ution CRT Support

65MIV-C / 65MIV2
16
1-5 MOTHERBOARD SPECIFICATION TABLE
Mode
VIA VT82C686A VIA VT82C686B
65MIV-C
North bridge VIA VT8605
South bridge
AGP Interface AGP 4X Mode
Bui d-in AC97 codec
Memory Supports PC133 and PC100 SDRAM and Virtua Channe
Memory (VCM) up to 1.5GB
3 DIMM S ots
Audio
IDE 2 x U tra ATA33/66
IDE ports
2 x U tra ATA33/66/100
IDE ports
I/O
YesNone
YesNone
Yes
4 x USB ports, 1 x FDD port, 2 x COM ports,
1 x LPT port, 1 x IrDA, 1 PS/2 Mouse, 1 PS/2 K/B
PCI s ot 3 x PCI Master S ots
VD-Tech
Temperature
Monitoring
BIOS writing
Protection
FLAT-PANEL
Disp ay
Connector
65MIV2
On-chip
Graphics S3 SAVAGE 4 AGP 4X
Optiona

Chapter1 Introduction
17
MEMO

65MIV-C / 65MIV2
18
CHAPTER 2
ATTENTION !!!
1. P ease refer to your processor insta ation or other
documentation attached with your CPU for more
detai ed insta ing instruction.
2. Insta ing a heat sink and coo ing fan is necessary for
proper heat dissipation from your CPU. Incorrect
insta ation may resu t in overheating and damage of
your CPU.
3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD make sure of correct specifi-
cation both of CPU CLOCK and RATIO. Incorrect set-
ting may cause damage to your CPU.
HARDWARE SETUP
2-1 CPU INSTALLATION
2-2 MEMORY INSTALLATION
2-3 HDD/FDD INSTALLATION
2-4 FOR CPU FREQUENCY AND VOLTAGE
2-5 FOR DEVICE ON BOARD
2-6 CONNECTORS CONFIGURATION
THIS CHAPTER CONTAINS THE FOLLOWING TOPICS :

Chapter2 Hardware Setup
19
2- 1 CPU INSTALLATION
WARNING !!!
Never run you processor without the heat sink properly and firmly attached.
PERMANENT DAMAGE ILL RESULT!
SOCKET 370
• Pull out the lever from the
socket, and then raise the le-
ver up to a 90-degree angle.
1
SOCKET 370
• Take notice of the red circles
as shown below. While insert-
ing the CPU into the socket,
you can find out there is a defi-
nite pin orientation for CPU
and socket.
2
SOCKET 370
• Make sure that the CPU is
placed into the socket tightly.
Then lower down the lever to
complete the CPU installation.
3

65MIV-C / 65MIV2
20
Insta ing DIMM
• Make sure you have the correct memory module type for your mainboard.
• Insert the module(s) as shown below, DIMMs have 16 -pins and two notches
that will be matched by the onboard DIMM socket. Memory modules are
installed by inserting them straight into the slot until they “click” in the right
place. They only fit in one direction, so do not force them in by a wrong
direction.
Removing DIMM
• Press down the holding clips on both sides of a DIMM socket and the
module will be released from it.
WARING !!!
• Make sure that you unplug your power supply when adding or removing
memory modules or other system components, failure to do so may cause
severe damage to both your mainboard and expansion cards.
• Be careful when inserting or removing DIMM, forcing a DIMM in or out of
a socket can be damaged the memory module or the socket. Some of DIMMs
contain EDO or FTP DRAM that accept only 5V power. These DIMM types
are incompliant with the mainboard, the M/B only supports 3.3V true
SDRAM DIMMs.
2- 2 MEMORY INSTALLATION
168-Pin DIMM Notch Key Definitions(3.3V)
DRAM Key Position Vo tage Key Position
Unbuffered 3.3V