SOLTEK SL-65MV Use and care manual

R
The Soul Of Computer Technology

USER NOTICE
Product Model : SL-65MV/65MV-X
Manual Revision : V1.0
Release Date : Jul 2000
This Users Guide & Technical Reference is for assisting system
manufacturers and end-users in setting up and installing the
mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek omputer Inc. is not responsible for print-
ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek omputer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek omputer Inc.
ompanies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.
Soltek computer inc. Provides this manual “As is “ without warranty
of any kind, either express or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for
a particular purpose. In no event shall Soltek computer inc. Be li-
able for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con-
sequential damages of any kind, even if Soltek computer inc. Has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright © 2000 Soltek Computer Inc. All Rights Reser ed.
• Intel, eleron, Pentium II, Pentium III are trademarks of Intel orporation.
• VIA, PM133, APOLLO PRO 133, VT82 694X and VT82 686A are trademarks of VIA
orporation.
• S3 Savage4 is tademarks of S3 orporation.
• Norton AntiVirus, Norton Ghost are trademarks of Symantec orporation.

SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi- hin, Taipei-
Hsien, Taiwan, R.O. .
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOLTEK KOREA INC.
Address : 1002, hungjin Bldg. 53-5 Wonhyo-Ro, 3-Ka,
Yongsan-Ku Seoul 140-113, Korea
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
MOKA HOLDING B.V.
Address : De Run 4428 5503 LR Veldhoven, the Netherlands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
SOUL TECHNOLOGY EUROPE B.V.
Address : Sydneystraat 52-54 3047 BP Rotterdam, the Nether-
lands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soultech-europe.com

4
65MV/65MV-X
C O N T E N T
CHAPTER 1
INTRODUCTION ........................................................................... 6
1-1 ITEM LIST HE KUP............................................................................6
1-2 PU ........................................................................................................6
1-3 HIPSET ................................................................................................6
1-4 MEMORY ...............................................................................................7
1-5 BIOS .......................................................................................................7
1-6 MULTI-I/O FUN TION ........................................................................... 7
1-7 FORM FA TOR .....................................................................................7
1-8 S3 SAVAGE4 A ELERATOR ..............................................................7
1-9 A ’97 ODE FUN TION ....................................................................8
1-10 OTHERS ..............................................................................................8
1-11.1 MOTHERBOARD LAYOUT --- 65MV ................................................ 9
1-11.2 MOTHERBOARD LAYOUT --- 65MV-X ........................................... 10
1-12 FLAT PANEL DESKTOP MONITOR SUPPORT ................................ 11
1-13 HIGH S REEN RESOLUTION RT SUPPORT ............................... 11
1-14 HIPSET DIAGRAM .......................................................................... 12
CHAPTER 2
HARDWARE SETUP ................................................................... 13
2-1 PU INSTALLATION............................................................................ 13
2-2.1 BUS RATIO SELE T ........................................................................ 14
2-2.2 BUS LO K SELE T.......................................................................15
2-2.3 PU FREQUEN Y ........................................................................... 16
2-3 JUMPER DEFINITIONS .......................................................................17
2-4 ONNE TORS ....................................................................................20
2-4.1 J2 AND J3 ......................................................................................... 20
2-4.2 HASSIS PANEL ONNE TOR ......................................................23
2-4.3 FLAT-PANEL DISPLAY ONNE TOR..............................................24
2-4.4 ATX POWER SUPPLY ONNE TOR ..............................................24
2-4.5 SE OND USB ONNE TOR...........................................................25
2-4.6 PS/2 MOUSE AND PS/2 KEYBOARD ..............................................26
2-4.7 IRQ DES RIPTION .......................................................................... 26
2-5 VOI E DIANOSTI FUN TION --- 65MV-X........................................ 28
CHAPTER 3
SOFTWARE SETUP .................................................................... 29
3-1 ABOUT SOLTEK SUPPORT D ..........................................................29
3-2 VIA HIPSET DRIVER INSTALLATION (4-IN-1 DRIVER)................... 29

5
65MV/65MV-X
3-3 ONBOARD S3® SAVAGE4TM VGA DRIVER INSTALLATION............33
3-4 A ’97 AUDIO ODE INSTALLATION................................................34
3-5 HARDWARE MONITOR INSTALLATION.............................................35
CHAPTER 4
BIOS SETUP ............................................................................... 36
4-1 INTRODU E THE BIOS ......................................................................36
4-2 WHAT IS BIOS SETUP ........................................................................ 36
4-3 HOW TO RUN BIOS SETUP ............................................................... 36
4-4 WHAT IS MOS ...................................................................................36
4-5 WHAT IS POST ....................................................................................37
4-6 BIOS UPGRADE ..................................................................................37
4-6.1 BEFORE UPGRADE BIOS ...............................................................37
4-6.2 UPGRADE PRO ESS ......................................................................37
4-7 MOS SETUP UTILITY ....................................................................... 40
4-8 STANDARD MOS SETUP ................................................................. 41
4-9 ADVAN ED BIOS FEATURES ............................................................44
4-10 ADVAN ED HIPSET FEATURES ...................................................48
4-11 INTEGRATED PERIPHERALS...........................................................53
4-12 POWER MANAGEMENT SETUP ......................................................58
4-13 PNP / P I ONFIGURATION ............................................................ 64
4-14 P HEALTH STATUS ......................................................................... 67
4-15 FREQUEN Y/VOLTAGE ONTROL.................................................68
4-16 LOAD OPTIMIZED DEFAULTS..........................................................68
4-17 SET SUPERVISOR / USER PASSWORD .........................................70
4-18 SAVE & EXIT SETUP......................................................................... 71
4-19 EXIT WITHOUT SAVING ...................................................................71

6
65MV/65MV-X
CHAPTER 1
INTRODUCTION
1-1 ITEM LIST CHECKUP
• Motherboard
• Support D
• User’s Manual
• 2-in-1 Bonus Pack D
• 2-in-1 Bonus Pack Manual
• Temperature Sensor able
• ATA66 IDE able
• RS232 able
1-2 CPU
• Supports Intel® F -PGA370 Pentium® III up to 1GHz, and F -PGA370
eleronTM & PPGA370 eleron processors up to 600MHz.
• Supports VIA yrix III processors up to 600MHz.
• Supports 66/100/133 MHz PU Front Side Bus (FSB).
• Supports processor voltage Auto-Detect circuit.
1-3 CHIPSET
• Adopts VIA PM133 North Bridge chipset and VIA VT82 686A South Bridge
chipset.
• VIA PM133 North Bridge:
--- Integrated VIA Apollo Pro 133A and S3® Savage4 in a single chip.
--- AGP Expansion Interface supporting AGP 4x, 2x, or 1x external AGP
graphics card upgrade.
--- 64-bit Advanced Memory controller supporting P 100/P 133 SDRAM.
--- AGP Specification Rev. 2.0 compliant.
--- Supports SideBus Addressing (SBA) mode.
--- Supports 266MHz 4x mode for AD and SBA signaling.
• VIA VT82 686A South Bridge:
-- - Integrated ISA Bus ontroller with integrated DMA, timer, and inter-
rupt controller.
--- Integrated Keyboard ontroller with PS2 mouser support.
--- Integrated USB ontroller with root hub and 4 function ports.
--- Integrated UDMA-33/66 master mode EIDE controller with enhanced

7
65MV/65MV-X
P I bus commands.
--- P I-2.2 compliant with delay transaction and remote power
management.
--- Supports ATAPI compliant devices including DVD devices.
--- Supports P I native and ATA compatibility modes.
--- APM v1.2 and A PI v1.0 compliant.
1-4 MEMORY
• Supports 3 DIMMs or 6 banks for up to 1.5GB of DRAM (256MB DRAM
technology)
• DRAM interface runs synchronous (66/66, 100/100, 133/133) mode or
pseudo-synchronous (66/100, 100/66, 100/133, 133/100) mode with FSB.
• oncurrent PU, AGP, and P I access.
1-5 BIOS
• Award BIOS 6.0
• Supports Plug & Play (PnP).
• Flash Memory for easy upgrade.
• Supports Advanced Power Management (APM) Rev 1.2 function.
• Advanced onfiguration Power Management Interface (A PI) Rev 1.0
compliant.
• Year 2000 compliant.
1-6 MULTI-I/O FUNCTION
• One floppy port supports up to 2.88MB.
• Provides 2 Built-In USB connector set.(Another 2 Built-In USB connector
set requires optional USB connector cable.)
• Ultra ATA33/66 bus master IDE supports up to 4 IDE devices (including
ZIP / LS-120 floppy devices).
• 2x 16550A Built-In fast UART compatible serial port connectors.
• Built-In SPP/EPP/E P parallel port connector.
• Built-In standard IrDA TX/RX header.
• Peripherals boot function with ATX power.
1-7 FORM FACTOR
• ATX form factor, 4 layers P B.
• Motherboard size: 19.0cm x 30.5cm
1-8 S3 SAVAGE4 ACCELERATOR
• Optimized Share Memory Architecture (SMA).

8
65MV/65MV-X
• 2 to 32MB frame buffer using system memory.
• Single cycle 128-bit 3D architecture.
• Full AGP 4x, including sideband addressing and execute mode.
• S3 DX7 texture compression (S3T ).
• High quality DVD video playback.
• Digital Visual Interface (DVI) 1.0 compliant.
• Flat Panel Monitor supports for all resolutions up to 1280x1024.
• 2D/3D resolutions up to 1920x1440.
• MPEG-2 video textures.
• Digital port for NTS /PAL TV encoder.
1-9 AC’97 CODEC FUNCTION
• Onboard A ’97 Audio odec controller chip.
1-10 OTHERS
• P I 2.2 compliant, 32-bit 3.3V P I interface with 5V tolerant inputs.
• Provides 5 P I master slots, 1 ISA slot, 1 AGP 4x slot, 1 AMR slot, 3
DIMM sockets, and 1 DV slot.
• lock Generator supports 1MHz linear clock setting.
• Provides DIP switch for easy setting.
• Supports S SI, D-ROM, ZIP, and LS-120 boot up function.
• Supports Wake On LAN (WOL) boot up function.
• Supports BIOS Writing Protection.
• Supports BIOS PU ore Voltage setting. (optional)
• Supports Hardware Monitor function.
• Supports Voice Diagnostic function for easy debug. (65MV-X Only)
• Supports Suspend To RAM (STR) function.

9
65MV/65MV-X
1-11.1 MOTHERBOARD LAYOUT --- 65MV
• Default Setting: Intel eleron 300A/66 MHz
13
JP9
13 13 13 13
JP5; JP6; JP7; JP8
13
JBAT1
13
J1
JFAN2
JFAN1
J2; J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
1 1
WOL1
JCD1
JCD2
1 4
1 4
AMR
AGP 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
DIMM1 DIMM2 DIMM3
FDD1
IDE2
IDE1
SOCKET 370
RT1
RT2
JP4
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97;
Codec
Clock; Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE; OUT
LINE; IN
MIC PS/2;
MOUSE PS/2; K/B
upper
lower
USB1 USB0
upper
lower
VIA
PM133
VIA;
686A
COM2
DVC1
ISA
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
PC100/PC133 SDRAM
STR LED

10
65MV/65MV-X
1-11.2 MOTHERBOARD LAYOUT --- 65MV-X
• Default Setting: Intel eleron 300A/66 MHz
13
JP9
13 13 13 13
JP5; JP6; JP7; JP8
13 13 13
JBAT1; JP10; JP11
13
J1
JFAN2
JFAN1
J2; J3
SPK RST_SW POWER/LED SUSLED
HD/LED IR PW_BN SMI
1 1
WOL1
JCD1
JCD2
1 4
1 4
AMR
AGP 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
DIMM1 DIMM2 DIMM3
FDD1
IDE2
IDE1
SOCKET 370
RT1
RT2
JP4
ATX POWER
Li
Battery
USB2
9 16 1 8
AC'97;
Codec
Clock; Generator
LPT1
VGA1 COM1
GAME/MIDI PORT
LINE; OUT
LINE; IN
MIC
PS/2; MOUSE PS/2; K/B
upper
lower
USB1 USB0
upper
lower
VIA
PM133
VIA;
686A
COM2
DVC1
ISA
FLASH BIOS
SW1
ON DIP
1 2 3 4 5 6 7 8
W5280
PC100/PC133 SDRAM
STR LED

11
65MV/65MV-X
1-13 HIGH SCREEN RESOLUTION CRT SUPPORT
Resolution Supported
System Memory Frame Buffer
Size (8MB Default)
640x480x8 /16/ 32 4MB 8MB 16/32MB
800x600x8 /16/ 32
1024x768x8 /16/ 32
1280x1024x8
1280x1024x16
1280x1024x32
1600x1200x8
1600x1200x16
1600x1200x32
1920x1440x8
1920x1440x16
High Screen Resolution CRT Support
1-12 FLAT PANEL DESKTOP MONITOR SUPPORT
• The VT8605 / 86 370 has the capability of displaying graphics on TFT
flat panel desktop monitors using a 12-bit digital interface to an external
encoder. The VT8605 / 86 370 also supports autoexpansion and center-
ing of all VGA text and graphics modes to ensure that the entire flat panel
display will be utilized. All resolutions are supported up to 1280 x 1024 by
flat panel desktop monitor. The resolution is Digital Visual Interface 1.0
specification compliant.

12
65MV/65MV-X
1-14 CHIPSET DIAGRAM
• The VT8605 is a high performance, cost-effective and energy efficient
SMA chip set for the implementation of AGP / P I / LP desktop personal
computer system with 66MHz, 100MHz, and 133MHz PU host bus (“Front
Side Bus”) frequencies and based on 64-bit Socket-370 (Intel Pentium
III, eleron) super-scalar processors. VT8605 is the VIA part number.
VT8605 S stem Block Diagram with VT82C686A PCI-TO-ISA South Bridge
ATA;
33/66
4X USB
AGP 4X Expansion;
Interface
VT82C
686A
South
Bridge
VT8605
SMA NB
552-pin
PBGA
PCI Slots
33MHz,;
32-bit PCI
64-bit 133/100/66 MHz
133/100/66 MHz
PC133/PC100 SDRAM
TV;
Encoder
TMDS;
Xmitter
Socket 370;
Celeron/PIII;
CPU
Serial Port
Floppy Disk
Parallel Port
EPROM
AC-97
MC-97
LPC
Integrated;
AC-97 Audio
AC-Link
FSB

13
65MV/65MV-X
SOCKET 370
CHAPTER 2
HARDWARE SETUP
2-1 CPU INSTALLATION
1. Pull the lever sidways away from the socket, and then raise the lever up
to a 90-degree angle.
2. Take note of the red circle as below picture. When insert the PU into
socket, you can find out there is a definite pin orientation for PU and
socket.
SOCKET 370

14
65MV/65MV-X
3. Make sure that the PU positions in the socket tightly, and then put the
lever down to complete the PU installation.
SOCKET 370
2-2.1 BUS RATIO SELECT
SW1 DIP1 ~ DIP4 SETTING
3.0x 3.5x
4.0x 4.5x
5.0x 5.5x
6.0x 6.5x
7.0x 7.5x
8.0x
ON
ON
ON ON
12345678
OFF
ON
ON
ON
12345678
OFF OFF
ON
ON
ON ON
12345678
OFF
ON
ON
ON
12345678
OFF OFF
ON
ON ON
12345678
OFF OFF
ON
ON
12345678
OFF OFF OFF
ON
ON
ON ON
12345678
OFF
ON
ON
ON
12345678
OFF OFF
ON
ON
ON
12345678
OFF OFF
ON
ON
12345678
OFF OFF OFF
ON ON
ON
12345678
OFF OFF

15
65MV/65MV-X
2-2.2 BUS CLOCK SELECT
Auto Select 66/100/133 MHz
(default)
SW1 DIP5 ~ DIP8 SETTING
ON
12345678
ON OFF
OFF
ON
66MHz
ON
12345678
ON
OFF OFF
ON
100MHz
ON
12345678
OFF OFF OFF
ON
133MHz
ON
12345678
OFF OFF OFF OFF

16
65MV/65MV-X
2-2.3 CPU FREQUENCY
High Screen Resolution CRT Support
ON
ON;
ON ON
12345678
OFF
ON
OFF OFF
ON
ON
ON;
ON
12345678
OFF OFF
ON
OFF OFF
ON
ON;
ON ON
12345678
OFF OFF
ON
OFF OFF
ON
ON;
ON
12345678
OFF OFF OFF
ON
OFF OFF
ON
ON
ON;
ON ON
12345678
OFF
ON
OFF OFF
ON
ON
ON;
ON
12345678
OFF OFF
ON
OFF OFF
ON
ON
ON;
ON
12345678
OFF OFF
ON
OFF OFF
ON
ON
ON;
12345678
OFF OFF OFF
ON
OFF OFF
ON
ON ON
ON;
12345678
OFF OFF
ON
OFF OFF
ON
Celeron 266/66 (66MHz * 4.0x)
Pentium II 400/100 (100MHz * 4.0x)
Pentium III 533EB/133 (133MHz * 4.0x)
#
Celeron 300/66 (66MHz * 4.5x)
Pentium II/III 450/100 (100MHz * 4.5x)
Pentium III 600EB/133 (133MHz * 4.5x)
#
Celeron 333/66 (66MHz * 5.0x)
Pentium II/III 500/100 (100MHz * 5.0x)
Pentium III 500E/100 (100MHz * 5.0x)
#
Pentium III 667B/133 (133MHz * 5.0x)
#
Celeron 366/66 (66MHz * 5.5x)
Pentium II/III 550/100 (100MHz * 5.5x)
Pentium III 550E/100 (100MHz * 5.5x)
#
Pentium III 733B/133 (133MHz * 5.5x)
#
Celeron 400/66 (66MHz * 6.0x)
Pentium II/III 600/100 (100MHz * 6.0x)
Pentium III 600E/100 (100MHz * 6.0x)
#
Celeron 433/66 (66MHz * 6.5x)
Pentium II/III 650/100 (100MHz * 6.5x)
Pentium III 650/100 (100MHz * 6.5x)
#
Celeron 466/66 (66MHz * 7.0x)
Pentium III 700/100 (100MHz * 7.0x)
#
Celeron 500/66 (66MHz * 7.5x)
Pentium III 750/100 (100MHz * 7.5x)
#
Celeron 533/66 (66MHz * 8.0x)
Manual DIP switches for di erse CPUs;
Using these CPUs which bus ratio exceed
8.0x, user can not change all alues from
the DIP switch but detection by BIOS
automatically.
O er 8.0x

17
65MV/65MV-X
Redirect USB port 3 to USB 2
connector (default)
JP5/JP6: USB PORT SELECT (1)
1
3
1
3
JP5 JP6
Redirect USB port 3 to AMR
1
3
1
3
JP5 JP6
2-3 JUMPER DEFINITIONS
• The figure below shows the location of the motherboard’s jumper blocks.
CAUTION
• Do not move the jumper with the power on. Always turn off the power and unplug
the power cord from the computer before changing the jumper. Otherwise, the
motherboard could be damaged.
PU FAN
JFAN1/JFAN2: ONBOARD FAN (12V)
JFAN2
JFAN1
SYSTEM FAN
Those connectors support processor/system/chassis cooling fan with +12V. Those
support three pin head connector. When connecting the wire to FAN connectors
user should give attention that the red wire is the positive and should be connected
to the +12V the black wire is Ground and should be connected to GND. If your
motherboard has Hardware Monitor chipset on-board you must use a specially
designed fan with speed sensor to take advantage of this function.
For fans with fan speed sensor every rotation of the fan will send out 2 pulses.
System Hardware Monitor will count and report the fan rotation speed.
NOTE 1: Always consult vendor for proper CPU cooling fan.
NOTE 2: CPU FAN supports the FAN control. You can install PC Alert utility.
This will automatically control the CPU FAN speed according to the
actual CPU temperature.
GND
+12V
SENSOR
Only for factory test.
JP4: FACTORY TEST
JP4

18
65MV/65MV-X
hinese Language
English Language (default)
JP10/JP11: VOICE DIAGNOSTIC LANGUAGE SELECT
3


1
3


13


1
3


1
JP10
JP10
JP11
JP11
Japanese Language
Spanish Language
3


1
3


13


1
3


1
JP10
JP10
JP11
JP11
Normal (default)
JP9: POWER LOST RESUME
1
3
JP9
Enabled
1
3
JP9
Redirect USB port 2 to USB 2
connector (default)
JP7/JP8: USB PORT SELECT (2)
1
3
1
3
JP7 JP8
Redirect USB port 2 to AGP
1
3
1
3
JP7 JP8
A battery must be used to retain the motherboard configuration in CMOS RAM.
NOTE : You can clear CMOS by shorting 2-3 pin when the system is POWER
OFF. Then return to 1-2 pin position (default). It may damage the
motherboard if clearing the CMOS in POWER ON status. Unplug the
power cord from power supply before clearing CMOS will be a best bet
for user.
Clear CMOS Data
Retain Data (default)
JBAT1: CLEAR CMOS DATA
JBAT1
3

1
JBAT1
3

1
Disabled
J1: ONBOARD AC'97 CODEC SELECT
1 3
J1
Enabled (default)
1 3
J1
This field allows you to enable or disable the onboard AC’97 audio feature. If you
want to use your own audio devices you may set this jumper to [Disabled].

19
65MV/65MV-X
onnect the Wake On LAN signal from LAN card 
to WOL1
WOL1 : WAKE ON LAN (WOL) FUNCTION
WOL1
This connector connects to a LAN card with a Wake On LAN output. The connector
powers up the system when a wake-up packet or signal is received through the
LAN card.
This feature requires that Wake On LAN feature is enabled at the BIOS “Power
Management Setup” and that your system has an ATX power supply with at least
720mA / +5V standby power.

20
65MV/65MV-X
2-4 CONNECTORS
• In this section we list all external connectors that user will use them.
2-4.1 J2 AND J3

123456789101112131415
J3
J2
PIN 1; +5V
HDD LED CONNECTOR
PIN 2; HDD LED SIGNAL
PIN 3; HDD LED SIGNAL
PIN 4; +5V
DESCRIPTION
This connector supplies power to the cabinet's IDE ;
acti ity LED. Read and write acti ity by de ices ;
connected to the Primary or SecondaryIDE ;
connector will cause the LED to light up.

1234567891011 12 13 14 15
J3
J2
INFRARED CONNECTOR
PIN 6; INFRARED TRANSMIT SIGNAL
PIN 7; GND
PIN 8; INFRARED RECEIVE SIGNAL
PIN 9; NONE
PIN 10; +5V
DESCRIPTION
This connector supports an optional wireless
transmitting and recei ing infrared module. This
module mounts to a small opening on system cases
that support this feature.
User must also configure the setting through
BIOS program "Peripheral Setup" to select whether
UART2 is directed for use with COM2 or IrDA.
Use the fi e pins and connect a ribbon cable from
the module to the motherboard's IR connector
according to the pin definitions.