SOLTEK SL-75KAV User manual

USER MANUAL V 1.2
R
SL-75KAV/75KAV-X

USER NOTICE
Product Model : SL-75KAV/75KAV-X
Manual Revision : V1.2
Release ate : May 2001
his Users’ Guide & Technical Reference is to help system
manufacturers and end-users set up and install the mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek omputer Inc. is not responsible for print-
ing or clerical errors. Information in this document is subject to
change without notice and does not represent a commitment on the
part of Soltek omputer Inc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek omputer Inc.
ompanies and products mentioned in this manual are for identifi-
cation purpose only. Product names appearing in this manual may
or may not be registered trademarks or copyrights of their respec-
tive companies.
Soltek computer inc. Provides this manual “As is “ without war-
ranty of any kind, either express or implied, including but not limited
to the implied warranties or conditions of merchantability or fitness
for a particular purpose. In no event shall Soltek computer inc. be
liable for any loss or profits, loss of business, loss of use or data,
interruption of business, or for indirect, special, incidental, or con-
sequential damages of any kind, even if Soltek computer inc. has
been advised of the possibility of such damages arising from any
defect or error in this manual or product.
Copyright 2001 Soltek Computer Inc. All Rights Reserved.
• AMD Athlon ThunderbirdTM, and DuronTM processors are trademarks of AMD orporation.
• VIA, KT-133A, VT8363A and VT82 686B are trademarks of VIA orporation.
T

SOLTEK AROUND THE WORLD
SOLTEK COMPUTER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi- hih, Taipei-
Hsien, Taiwan, R.O. .
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOUL TECHNOLOGY EUROPE B.V.
Address : Hongkongstraat 55, 3047 BR, Rotterdam, The
Netherlands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soultech-europe.com

75KAV/75KAV-X
4
C O N T E N T
Chapter 1 Introduction............................................... 9
1-1 MAINBOARD SPE IFI ATION .................................................. 10
1-1-1 PRO ESSOR ................................................................................... 10
1-1-2 HIPSET ........................................................................................... 10
1-1-3 ADVAN ED HIGH PERFORMAN E DRAM ONTROLLER........... 10
1-1-4 FULL FEATURED A ELERATED GRAPHI S PORTS ................. 10
(AGP) ONTROLLER................................................................. 10
1-1-5 MULTI-I/O FUN TION ...................................................................... 10
1-1-6 EXPANSION SLOTS ......................................................................... 11
1-1-7 AWARD BIOS V6.0, SUPPORTING ................................................. 11
1-1-8 SOUND ONTROLLER .................................................................... 11
1-1-9 POWER MANAGEMENT .................................................................. 11
1-1-10 FORM FA TOR .............................................................................. 12
1-1-11 HARDWARE MONITORING ........................................................... 12
1-1-12 OTHERS ......................................................................................... 12
1-2 MAINBOARD LAYOUT ............................................................... 13
1-2-1 MAINBOARD LAYOUT --- 75KAV ..................................................... 13
1-2-2 MAINBOARD LAYOUT --- 75KAV-X ................................................. 14
1-3 HIPSET DIAGRAM................................................................... 15
Chapter 2 Hardware Setup ...................................... 17
2-1 PU INSTALLATION .................................................................. 18
2-2 MEMORY INSTALLATION .......................................................... 19
2-3 A ELERATED GRAPHI S PORT(AGP) PRO INSTALLATION ..... 21
2-4 HDD/FDD INSTALLATION .......................................................... 22
2-5 SWIT H SETTING FOR PU FREQUEN Y AND VOLTAGE... 24
2-5-1 INFORMATION ON AMD SO KET 462 PRO ESSOR ................... 24
2-5-2 PU EXTERNAL FREQUEN Y SETTING (BY SW1) ...................... 25
2-5-3 BUS RATIO SELE T (BY SW2 DIP1-4/JP17) .................................. 26
2-6 JUMPER SETTING FOR DEVI ES ON BOARD: ...................... 27

Content
5
2-6-1 JUMPER JBAT1 FOR LEARING MOS DATA: ............................. 27
2-6-2 JP1/JP2 USB PORT SELE T ........................................................... 28
2-6-3 JP3 FOR FA TORY TEST ONLY ..................................................... 28
2-6-4 JP7 POWER LOST RESUME ........................................................... 29
2-6-5 JP9 USB WAKE UP .......................................................................... 29
2-6-6 JP10/JP11 MEMORY MODULE VOLTAGE SELE T ....................... 30
2-7 ONNE TORS ONFIGURATIONS ......................................... 31
2-7-1 ONBOARD FAN ONNE TOR (FAN1/FAN2/FAN3) ........................ 31
2-7-2 WAKE ON LAN FUN TION (WOL1) ................................................ 32
2-7-3 D-ROM AUDIO ONNE TOR ( D-IN1/ D-IN2) ........................... 32
2-7-4 THERMAL SENSOR ONNE TOR (RT2) ....................................... 33
2-7-5 HEADER J3&J4 ............................................................................... 34
2-7-6 HASSIS PANEL ONNE TOR ..................................................... 37
2-7-7 ATX POWER SUPPLY ONNE TOR ............................................. 38
2-7-8 PS/2 MOUSE AND PS/2 KEYBOARD ............................................. 38
2-7-9 SERIAL PORT ONNE TOR.......................................................... 39
2-7-10 SE OND USB HEADER (USB2) ................................................... 40
2-7-11 IRQS DES RIPTION FOR VARIOUS DEVI ES ............................ 41
2-8 VOI E DIAGNOSTI FUN TION----ONLY FOR 75KAV-X........ 42
2-8-1 VOI E DIAGNOSTI FUN TION SELE T (BY JP4/JP5) ............... 43
2-8-2 VD-TE H ONTROLLER HIP (BY JP8) ........................................ 43
Chapter 3 Software Setup ....................................... 45
ABOUT SUPPORT D ..................................................................... 45
3-1 VIA HIPSET DRIVER INSTALLATION (4-IN-1 DRIVER) ......... 46
3-2 A 97 AUDIO ODE DRIVER INSTALLATION ........................ 49
3-3 HARDWARE MONITOR INSTALLATION ................................... 51
Chapter 4 BIOS Setup .............................................. 55
THE BIOS ......................................................................................... 55
4-1 WHAT IS BIOS SETUP ............................................................... 56
4-2 HOW TO RUN BIOS SETUP ...................................................... 56
4-3 WHAT IS MOS ......................................................................... 56
4-4 WHAT IS POST .......................................................................... 56

75KAV/75KAV-X
6
4-5 BIOS UPGRADE......................................................................... 56
4-5-1 BEFORE UPGRADING BIOS ........................................................... 57
4-5-2 UPGRADE PRO ESS ...................................................................... 57
4-6 BIOS SETUP°X MOS SETUP UTILITY .................................... 61
4-6-1 STANDARD MOS SETUP .............................................................. 62
4-6-2 ADVAN ED BIOS FEATURES ......................................................... 65
4-6-3 ADVAN ED HIPSET FEATURES .................................................. 70
4-6-4 INTEGRATED PERIPHERALS ......................................................... 75
4-6-5 POWER MANAGEMENT SETUP ..................................................... 79
4-6-6 PNP / P I ONFIGURATION ........................................................... 86
4-6-7 SMARTDO ANTI-BURN SHIELD ................................................... 90
4-6-8 FREQUEN Y/VOLTAGE ONTROL ................................................ 93
4-6-9 LOAD OPTIMIZED DEFAULTS ......................................................... 94
4-6-10 SET SUPERVISOR / USER PASSWORD ...................................... 96
4-6-11 SAVE & EXIT SETUP ...................................................................... 97
4-6-12 EXIT WITHOUT SAVING ................................................................ 97
Appendices .................................................................... 98
APPENDI ES-1 TE HNI AL TERMS INTRODU TION ............... 99
APPENDI ES-2 IDENTIFYING BIOS VERSION AND .................. 100
BIOS PART NUMBER ........................................ 100
APPENDI ES-3 IDENTIFYING MAINBOARD \ MODEL .............. 102
NUMBER............................................................. 102

Content
7
MEMO

75KAV/75KAV-X
8
Mainboard
Support D
User’s Manual
Bundled Bonus Pack D
Bundled Bonus Pack Manual
Temperature Sensor able
ATA66/100 IDE able
RS232 able
FDD able
ITEMLIST CHECKUP

Chapter1 Introduction
9
CHAPTER 1
INTRODUCTION
• This chapter briefly introduces the characteristics of this mainboard. It
includes the information regarding the chipset, PU types, built-in
functions and layout. Users will have more ideas about mainboards after
reading this chapter.
NJN=MAINBOARD SPECIFICATION
NJO=MAINBOARD LAYOUT
NJP=CHIPSET DIAGRAM
THIS CHAPTER CONTAINS THE FOLLOWING TOPICS :

75KAV/75KAV-X
10
1-1 MAINBOARD SPECIFICATION
1-1-1 PROCESSOR
• Supporting AMD Athlon Thunderbird processors up to 1.5GHz.
• Supporting AMD Athlon Duron processors up to 1.2GHz.
• Supporting processor VID (voltage ID) and FID (frequency ID) auto detection.
• Supporting AMD Athlon processor with 200 and 266MHz Front Side bus.
1-1-2 CHIPSET
• North Bridge VIA VT8363A (KT-133A) system controller High Performance
Athlon PU Interface.
• South Bridge VIA VT82 686B.
1-1-3 ADVANCED HIGH PERFORMANCE DRAM
CONTROLLER
• Supporting P 133 and P 100 SDRAM and Virtual hannel Memory (V M)
SDRAM up to 3 DIMMs.
• 64-bit data width and 3.3V DRAM interface.
• Supporting up to 1.5 GB memory space.
• Supporting Different DRAM types used in mixed combinations.
• P I-2.2 compliant, 32 bit 3.3V P I interface with 5V tolerant inputs.
1-1-4 FULL FEATURED ACCELERATED GRAPHICS PORTS
(AGP) CONTROLLER
• Synchronous and pseudo-synchronous with the host PU bus with optimal
skew control P I AGP Mode 33MHz/66MHz/100MHz DDR 3x synchronous.
• Supporting 66MHz 1x, 2x and 4x modes for AD and SBA signaling.
• AGP v2.0 compliant.
1-1-5 MULTI-I/O FUNCTION
• Two UARTs for complete Serial Ports.
• One dedicated IR connector supporting:
--A third serial port dedicated to IR function either through the two complete serial
ports or the third delicated port Infrared-IrDA (HPSIR) and ASK( Amplitude Shift
Keyed) IR.
• Multi-mode parallel connector supporting:

Chapter1 Introduction
11
--Standard mode, E P and EPP.
• Floppy Disk connector supporting:
--Two FDDs with drive swap function.
• Universal Serial Bus connector supporting:
--USB v1.1 and Intel Universal H I v1.1 compatible.
--2 built-in USB connectors, in addition to one internal USB header which requires
a USB cable to support 2 more optional USB ports.
• PS/2 keyboard connector.
• PS/2 Mouse connector.
1-1-6 EXPANSION SLOTS
• Five P I bus Master slots.
• One ISA slot.
• One AGP Pro 4x mode slot.
• Three DIMM slots.
1-1-7 AWARD BIOS V6.0, SUPPORTING
• Plug & Play V1.0.
• Flash Memory for easy upgrade.
• Year 2000 compliant.
• BIOS writing protection.
• SMARTDO ANTI-BURN SHIELD.
• RedStorm Overclocking Tech.
1-1-8 SOUND CONTROLLER
• SoundBlaster Pro Hardware and Direct Sound Ready A 97 Digital Audio
ontroller with odec onboard.
1-1-9 POWER MANAGEMENT
• A PI 1.0 compliant (Advanced onfiguration and Power Interface).
• APM V1.2 compliant (Advanced power management).
• Supporting A PI suspend STR mode (Suspend To RAM) and POS mode
(Power On Suspend).
• Supporting Wake On LAN (WOL) & Wake On Modem.
• Supporting real time clock (RT ) with date alarm, month alarm, and cen-
tury field.

75KAV/75KAV-X
12
• Supporting USB boot-up Function.
1-1-10 FORM FACTOR
• ATX form factor, 4 layer P B.
• Mainboard size: 22.0cm x 30.5cm.
1-1-11 HARDWARE MONITORING
• Programmable control, status, to provide monitoring and alarm for flexible
desktop management of hardware temperature. (software included in sup-
port D)
• 5 positive voltage statuses monitoring.
• 2 temperature statuses monitoring.
• 2 fan speeds statuses monitoring.
1-1-12 OTHERS
• lock generator supporting 1 MHz linear clock setting.

Chapter1 Introduction
13
1-2 MAINBOARD LAYOUT
1-2-1 MAINBOARD LAYOUT --- 75KAV
• Default Setting: 100MHz PU External clock.
SOCKET A
FLASH BIOS
VIA
KT-133A
VT8363A
VIA
VT82C
686B
ATX POWER SW1
LPT1
COM 1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
USB2
AC'97
Codec
Li
Battery
ISA
J3 J4
SPK RST PWR/LED T/LED
HDD/LED IR PWR SMI
++
--
+-
1 15 1 15
AGP PRO 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
FDD1
IDE2
IDE1
DIMM1 DIMM2 DIMM3
14
14
1 3
1 3
1 3
1 3
JBAT1
JP7
JP1
JP2
1 3
JP9
WOL1
CD_IN2
CD_IN1
FAN2
W5280
FAN1
JP3
RT2
SSF1
ZD1
1 3
1 3
JP10
JP11
ON
DIP
5 4 3 2 1
Clock
Generator
SW2
USB1 USB0 PS/2
MOUSE PS/2 K/B
upper
lower
upper
lower
ON
DIP
4 3 2 1
1
16
1 3
JP17
FAN3
COM 2
1
10

75KAV/75KAV-X
14
SOCKET A
FLASH BIOS
ATX POWER SW1
LPT1
COM 1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
AC'97
Codec
Li
Battery
ISA
J3 J4
SPK RST PWR/LED T/LED
HDD/LED IR PWR SMI
++
--
+-
1 15 1 15
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
FDD1
IDE2
IDE1
DIMM1 DIMM2 DIMM3
14
14
1 3
1 3
1 3
JP7
JP1
JP2
1 3
JP9
WOL1
CD_IN2
CD_IN1
FAN2
W5280
FAN1
SSF1
ZD1
1 3
1 3
JP10
JP11
ON
DIP
5 4 3 2 1
Clock
Generator
SW2
USB1 USB0 PS/2
MOUSE PS/2 K/B
upper
lower
upper
lower
1 3
1 3
1 3
JP4
JP5
JBAT1
RT2
1 3
JP8
W5280
USB2
1
16
AGP PRO 4X
VIA
KT-133A
VT8363A
VIA
VT82C
686B
1 3
JP17
ON
DIP
4 3 2 1
JP3
FAN3
COM 2
1
10
1-2-2 MAINBOARD LAYOUT --- 75KAV-X
• Default Setting: 100MHz PU External clock.

Chapter1 Introduction
15
Diagram of KT133A System Block Using the VT82C686B South Bridge
KT133A
VT8363A
North Bridge
552 BGA
South Bridge
352 BGA
VT82C
686B Power Plane & Peripheral Control
GPIO and ACPI Events
Hardware Monitoring Inputs
Keyboard / PS2 Mouse
Serial Ports 1 and 2
Parallel Port
Floppy Drive Interface
MIDI / Game Ports
RTC Crystal
PCLK
SMBus
Clock
Generator
PCISTP#
CPUSTP#
MCLK
In
Data
Address
Out
SDRAM
Clock
Buffer
GCLK
CFWDRST CONNECT
PROCRDY
GCKRUN#
AGP Bus
PCI Bus
SUSCLK,
SUSST1#
PCKRUN#
ATA 33/66/100
USB Ports 0 - 3
ISA Bus
AC97 Link
Memory Bus
CKE
HCLK
PCLK
SYSCLK, SYSCLK#
INTR, NMI, SMI#, STPCLK#,
IGNNE#, FERR#, A20M#,
PWROK, INIT#, RESET#
Athlon
Host CPU
3D Graphics
Controller
AC97 Audio Codec
BIOS ROM
1-3 CHIPSET DIAGRAM
• The KT-133A / VT82 686B chipset is a high performance, cost-effective
and energy efficient system controller for the implementation of AGP / P I
/ ISA desktop personal computer system based on 64-bit Socket-A (AMD
Athlon) processors.

75KAV/75KAV-X
16
MEMO

Chapter2 Hardware Setup
17
CHAPTER 2
ATTENTION !!!
1. Please refer to your processor installation or other
documentation attached with your CPU for more
detailed installing instruction.
2. Installing a heat sink and cooling fan is necessary for
proper heat dissipation from your CPU. Incorrect
installation may result in overheating and damage of
your CPU.
3. Before changing the setting of CPU Vcore from BIOS
program, user SHOULD make sure of correct specifi-
cation both of CPU CLOCK and RATIO. Incorrect set-
ting may cause damage to your CPU.
HARDWARE SETUP
OJN=CPU INSTALLATION
OJO=MEMORY INSTALLATION
OJP=HDD/FDD INSTALLATION
OJQ=AGP PRO INSTALLATION
OJR=FOR CPU FREQUENCY AND VOLTAGE
OJS=FOR DEVICE ON BOARD
OJT=CONNECTORS CONFIGURATION
OJU=VOICE DIAGNOSTIC FUNCTION
THIS CHAPTER CONTAINS THE FOLLOWING TOPICS :

75KAV/75KAV-X
18
SOCKET 462
AMD
SOCKET 462
• Pull out the lever from the
socket, and then raise the le-
ver up to a 90-degree angle.
1
2-1 CPU INSTALLATION
• Take notice of the red circles
as shown below. While insert-
ing the PU into the socket,
you can find out there is a defi-
nite pin orientation for PU
and socket.
2
WARNING:
• Make sure that +5V DCV and +3.3 DCV capabilities of your power supply are
suitable for the processor.
• Any attempt to operate the AMD Athlon or Duron processor without a suitable
coolin Fan will dama e the processor and other components.

Chapter2 Hardware Setup
19
2-2 MEMORY INSTALLATION
SOCKET A
FLASH BIOS
VIA
KT-133A
VT8363A
VIA
VT82C
686B
ATX POWER SW1
LPT1
COM 1
GAME/MIDI PORT
LINE OUT
LINE IN
MIC
USB2
AC'97
Codec
Li
Battery
ISA
J3 J4
SPK RST PWR/LED T/LED
HDD/LED IR PWR SMI
++
--
+-
1 15 1 15
AGP PRO 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
FDD1
IDE2
IDE1
DIMM1 DIMM2 DIMM3
14
14
1 3
1 3
1 3
1 3
JBAT1
JP7
JP1
JP2
1 3
JP9
WOL1
CD_IN2
CD_IN1
FAN2
W5280
FAN1
JP3
RT2
SSF1
ZD1
1 3
1 3
JP10
JP11
ON
DIP
5 4 3 2 1
Clock
Generator
SW2
USB1 USB0 PS/2
MOUSE PS/2 K/B
upper
lower
upper
lower
ON
DIP
4 3 2 1
1
16
1 3
JP17
FAN3
COM 2
1
10
AMD
SOCKET 462
• Make sure that the PU is
placed into the socket tightly.
Then lower down the lever to
complete the PU installation.
3
NOTICE : When LED “ZD1” is on ,
meanin that 3.3V is operatin and
flowin into DIMM slots, please do not
add or remove memory modules.

75KAV/75KAV-X
20
Installing DIMM
• Make sure you have the correct memory module type for your mainboard.
• Insert the module(s) as shown below, DIMMs have 168-pins and two notches
that will be matched by the onboard DIMM socket. Memory modules are
installed by inserting them straight into the slot until they “click” in the right
place. They only fit in one direction, so do not force them in by a wrong
direction.
Removing DIMM
• Press down the holding clips on both sides of a DIMM socket and the
module will be released from it.
168-Pin DIMM Notch Key Definitions(3.3V)
DRAM Key Position Voltage Key Position
Unbuffered 3.3V
WARNING!!!
• Make sure to unplu your power supply before addin or removin memory mod-
ules or other system components. Failure to do so may cause severe dama e to
both your mainboard and expansion cards.
• Be careful when insertin or removin DIMM. Forcin a DIMM in or out of a socket
improperly may dama e the memory module or the socket. Some DIMMs which con-
tain EDO or FTP DRAM are incompliant with the mainboard. The M/B supports 3.
3V true SDRAM DIMMs only.