SOLTEK SL-85DR-C User manual

Mainboard
SL-85DR-C User Manual V1.0
R
The Soul Of Computer Technology

his Users Guide & Technical Reference is to help system
manufacturers and end-users set up and install the mainboard.
Every effort has been made to ensure that the information in this
manual is accurate. Soltek Computer nc. is not responsible for printing or
clerical errors. nformation in this document is subject to change
without notice and does not represent a commitment on Soltek
Computer nc.
No part of this manual may be reproduced, transmitted, translated
into any language in any form or by any means, electronic or
mechanical, including photocopying and recording, for any purpose
without the express written permission of Soltek Computer nc.
Companies and products mentioned in this manual are for identification
purpose only. Product names appearing in this manual may or may
not be registered trademarks or copyrights of their respective
companies.
Soltek Computer nc. provides this manual “As is “ without warranty
of any kind, either express or implied, including but not limited to the
implied warranties or conditions of merchantability or fitness for a
particular purpose. n no event shall Soltek Computer nc. be liable
for any loss or profits, loss of business, loss of use or data, interruption of
business, or for indirect, special, incidental, or consequential damages of
any kind, even if Soltek Computer nc. has been advised of the possibility
of such damages arising from any defect or error in this manual or product.
Copyright © 2001 Soltek Computer Inc. All Rights Reserved.
NO ICE Product Model : SL-85DR-C
Manual Revision : V1.0
Release Date : ovember 2001
• ntel Pentium 4 and Northwood are trademarks of ntel Corporation.
• ntel 845-D is trademark of ntel Corporation.

SOLTEK AROUND THE WORLD
SOL EK COMPU ER INC.
Address : 7F, No. 306-3, Ta-Tung Rd, Sec.1, Hsi-Chih, Taipei-
Hsien, Taiwan, R.O.C.
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soltek.com.tw
SOUL ECHNOLOGY EUROPE B.V.
Address : Hongkongstraat 55, 3047 BP Rotterdam. The Neth-
erlands
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]
Web site : http://www.soultech-europe.com
SOL EK KOREA INC.
Address : 1002, Chung Jin Bldg. 53-5 Wonhyo-Ro, 3-Ka,
Yongsan-Ku Seoul 140-113, Korea
Telephone : [phone]
Fax : [phone]
E-mail : [email protected]

85DR-C
4
CO TE T
Chapter 1 Specification ............................................................ 8
1-1 Mainboard Specifications ...........................................................9
1-1.1 CPU Socket .................................................................................... 9
1-1.2 Sysem Chipset Architecture ........................................................... 9
1-1.3 Memory .......................................................................................... 9
1-1. AWARD BIOS V6.0 ....................................................................... 9
1-1.5 Hardware Monitoring ..................................................................... 9
1-1.6 Sound Controller .......................................................................... 10
1-1.7 Multi-I/O Function ....................................................................... 10
1-1.8 Expansion Slots ............................................................................ 10
1-1.9 Accelerated Graphics port (AGP) Interface ................................. 10
1-1.10 FORM FACTOR ........................................................................ 10
1-1.11 Power Management .................................................................... 11
1-2 Mainboard Layout .....................................................................12
1-3 Chipset System Block Diagram ................................................13
Chapter 2 Hardware Setup .................................................... 15
2-1 Pentium CPU Installation with Socket 78............................16
2-2 Pentium CPU Fan Installation: ..............................................17
2-3 Memory Installation ..................................................................18
2-3.1 To Install DIMM Module ............................................................. 18
2-3.2 To Remove a DIMM: ................................................................... 18
2- AGP X (Accelerated Graphics Port) Installation ..................19
2-5 HDD/FDD Installation ..............................................................20
2-6 Jumper and Switch Settings ......................................................22
2-6.1 Switch 1 CPU Clock Select......................................................... 23
2-6.2 Factory Test (By JP2) ................................................................... 2
2-6.3 Memory Module Voltage Select (By JP3/JP ) ............................. 2

5
Content
2-6. JP13 Memory Stick/Secure Digital Memory Card Select............ 25
2-6.5 AGP Voltage Select (By JAGP1/JAGP2) ..................................... 25
2-6.6 JBAT1 Clear CMOS ..................................................................... 26
2-7 Other Connectors Configuration ...............................................27
2-7.1 On Board FAN Connectors (FAN1,FAN2, FAN3) ...................... 27
2-7.2 WOL1 Wake On LAN .................................................................. 28
2-7.3 CD-ROM Audio Connector (CD9/CD10) ................................... 29
2-7. Thermal Sensor Connector RT2 (Optional) ................................. 30
2-7.5 Complex Header NJ1 ................................................................... 31
2-7.6 ATX Power Supply Connectors version 2.03 for Pentium ........ 33
2-7.7 CMEM1 Memory Stick/Secure Digital Memory Card Connector.. 3
2-7.8 Communication And Networking Riser Slot (CNR) ................... 35
2-7.9 Smart Card Reader Connector (SCR1) ........................................ 36
2-7.10 USB Header (Header USB1) ..................................................... 37
2-7.11 PS/2 Mouse And PS/2 Keyboard................................................ 37
2-7.12 Chassis Panel Connector ............................................................ 38
2-8 IRQ Description ........................................................................39
Chapter 3 Software Setup ...................................................... 41
3-1 Open up the Support CD and choose Drivers and Utilities ...... 2
3-2 Install “Intel Chipset Software Installation Utility” .................. 3
3-3 Install “Intel Application Accelerator” ......................................
3- AC’97 Audio Driver Installation ............................................... 6
3-5 Install Hardware Monitor Utility .............................................. 7
3-5.1 Installation ................................................................................... 7
3-5.2 Verification .................................................................................. 8
Chapter 4 BIOS Setup............................................................ 50
-1 About BIOS Setup .....................................................................51
-2 To run BIOS Setup ....................................................................51

85DR-C
6
-3 About CMOS.............................................................................51
- The POST ( Power On Self Test ) .............................................51
-5 To upgrade BIOS.......................................................................52
-5.1 Before Upgrading BIOS ............................................................... 52
-5.2 Upgrade Process ........................................................................... 52
-6 BIOS Setup --- CMOS Setup Utility.........................................55
-6.1 CMOS Setup Utility ..................................................................... 55
-6.2 Standard CMOS Setup ................................................................. 56
-6.3 Advanced BIOS Features ............................................................. 59
-6. Advanced Chipset Features .......................................................... 63
-6.5 Integrated Peripherals................................................................... 66
-6.6 Power Management Setup............................................................ 72
-6.7 PNP / PCI Configuration .............................................................. 77
-6.8 SmartDoc Anti-Burn Shield ......................................................... 80
-6.9 Frequency/Voltage Control .......................................................... 82
-6.10 Load Optimized Default ............................................................. 85
-6.11 Set Supervisor / User Password.................................................. 86
-6.12 Save & Exit Setup ...................................................................... 87
-6.13 Exit Without Saving ................................................................... 87
Appendices .............................................................................. 89
Appendix-1 Identifying BIOS version and BIOS part Number .....90
Appendix-2 Identifying Mainboard model Number ......................91
Appendix-3 Technical Terms...........................................................92

7
Content
Mainboard
Support CD
Bundled Bonus Pack CD
Bundled Bonus Pack Manual
Temperature Sensor Cable (Optional)
ATA66/100 DE Cable
RS232 Cable
FDD Cable
User’s Manual
ITEM LIST CHECKUP

8
85DR-C
Chapter 1 Specification
• This chapter introduces the characteristics of this series of mainboards.
t includes the information on the chipset, CPU types, built-in functions
and layout. Users will have more ideas about this powerful series after
reading this chapter.
The topics contained in this chapter are:
1-1 Mainboard Specifications
1-2 Mainboard Layout
1-3 Chipset Diagram
Introduction

9
Chapter 1 Specification
1-1.1 CPU Socket
• CPU Socket 478B on board, supporting ntel® Pentium 4 and Northwood
processors in the 478-pin package for 400MHz System Bus.
1-1.2 Sysem Chipset Architecture
• NTEL 845-D Chipset Memory Control Hub (MCH):
To work with ntel Pentium 4 Processor for managing and arbitrating
between 4 interfaces:
-- the System Bus (Host nterface);
-- the memory nterface;
-- the AGP Port and the Hub nterface;
• MCH Clockings:
-- Asynchronous;
-- System Bus target speed at 400MHz;
-- AGP and Hub nterface constantly at 66MHz base;
• ntel CH2 Chipset (Second generation /O Controller Hub):
Communicating with ntel 845-D by the Hub interface at 66MHz/266MB/s;
-- Transmitting nterrupt related messages;
-- Transmitting Power management events;
-- Transmitting SM , SC , SERR indication messages;
1-1.3 Memory
2pcs of D MM on board for single / double sided D MMs, supported by
2.5V default voltage:
• ntel 845-D MCH directly supporting one channel of DDR SDRAM up to
2GB capacity.
1-1.4 AWARD BIOS V6.0
• Supporting Plug & Play V1.0.
• FLASH MEMORY for easy upgrade.
• Supporting B OS writing protection.
• Year 2000 compliant.
1-1.5 Hardware Monitoring
• Programmable control, status, to provide monitoring and alarm for flexible
desktop management of hardware temperatures. Utility Software is
enclosed in Support CD to help display monitoring statuses of:
-- 6 positive voltages, 3 types of hardware temperatures, 3 Fan speeds;
1-1 Mainboard Specifications

10
85DR-C
1-1.7 Multi-I/O Function
• ntegrated DE Controller, supporting:
-- 2x Ultra ATA100 / 66 / 33 Connectors
-- Two UARTs for Complete Serial Ports (2x COM ).
• Dedicated R Connector:
-- Third serial port dedicated to R function either through the two complete serial
ports or the third dedicated port nfrared- rDA (HPS R) and ASK (Amplitude Shift
Keyed) R.
• Multi-mode parallel connector:
-- Standard mode, ECP and EPP support.
• Floppy Disk connector:
-- One FDD connector with drive swap support.
• Universal Serial Bus connector:
-- USB V1.1 compliant.
-- 2 built-in USB connectors and one USB Header (USB1) which requires an
optional USB cable to provide 2 more optional USB ports.
• PS/2 Keyboard connector.
• PS/2 Mouse connector.
1-1.8 Expansion Slots
• Six PC bus Master slots.
• One AGP 4x mode slot.
• One CNR slot.
• One SCR1 slot.
• Two D MM slots.
• One CMEM1 slot.
1-1.9 Accelerated Graphics port (AGP) Interface
• One AGP slot on board is supported by the ntel 845-D Chipset MCH
AGP nterface in 1.5V mode (with AGP voltage selectable in B OS Setup):
-- AGP v2.0 compliant.
1-1.10 FORM FACTOR
• ATX form factor.
• This mainboard is compatible with both ATX Power Supply Version 2.03
(with +12V Power Connector) and the older ATX Power Supply (with
Peripheral Power Connector).
• Mainboard size: 30.5cm x 21.0cm.

11
Chapter 1 Specification
1-1.6 Sound Controller
• SoundBlaster Pro Hardware and Direct Sound Ready AC97 Digital Audio
Controller with Codec onboard.
1-1.11 Power Management
• ACP 1.0B compliant (Advanced Configuration and Power nterface).
• APM V1.2 compliant (Legacy power management).
• Supporting ACP suspend POS mode (Power On Suspend).
• System event monitoring with two event classes.
• Supporting Wake On LAN (WOL) & Wake On Ring.
• Supporting real time clock (RTC) with date alarm, month alarm, and
century field.

12
85DR-C
1-2 Mainboard Layout
1 4
DIMM1 DIMM2
1
mPGA478B
Intel RG82845-D
Intel RG82845
1 3
FAN2
1 3
FAN3
1 3
FAN1
AGP 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
PCI 6
FWH
WOL1
1 3
LPC I O
Controller
AC'97
Codec
CNR
SW1
ON DIP
1 2 3 4 5
IDE2
IDE1
1
1
1
FDC1
Li
Battery
82801BA
JBAT1
1 3
JP3 JP4
1 3 1 3
JP13
1 3
JP2
1 3
1 3
1 3
RT2
RT1
Peripheral Power Connector
+12 Power Connector
4 3 2 1
Main Power Connector
USB1
1
16
PS 2 MOUSE
PS 2 K B
upper
lower
USB1 USB0
upper
lower
LPT1
COM1COM2
MIC
GAME MIDI PORT
LINE OUT
LINE IN
NJP1
SPEAK RST KEYLOCKPWR LED SUS_LED
IDE_LED IR PWR SMI
30
1
++
--
+-
CD9
CD10
1 4
JAGP1
JAGP2
LED1
SCR1
CMEM1
1

13
Chapter 1 Specification
ntel 82845-DMCH + CH2 Chipset Diagram
1-3 Chipset System Block Diagram
System
Memory
PCI
Agent
Super
I O
PC133 SDRAM
1.06GB s
FWH
(Firmware Hub)
ICH2
(I O Controller Hub)
Intel 82845-D
MCH
-System Bus
-Memory Controller
-AGP Controller
-Hub Interface
PCI Bus
GPIO
System Bus (4x100MHz)
Bandwidth 3.2GB s
4 USB Ports
2 IDE Drives
Ultra DMA100 66
PCI Slots
Audio Codec(s)
LAN Connect
Intel Pentium 4 Processor
AGP Graphics
Controller
AC'97 2.1
LPC I F
Memory
Interface
AGP 4x
(1.5V)
1.06GB s
Keyboard
Mouse,FD,
PPSP,IR

14
85DR-C
M
e
m
o

15
Chapter 2 Hardware Setup
Chapter 2 Hardware Setup
To Get things ready for Hardware setup !!!
1. We recommend to install your CPU before any other componentes. For
detailed installalation instructions of processor, you can also refer to the
pamphlet enclosed in your CPU package.
2. nstalling a cooling fan with a good heatsink is a must for proper heat
dissipation for your CPU. Get ready an appropriate fan with heatsink for
proper installation. nproper fan and installation will damage your CPU.
3. n case CPU Vcore, CPU clock or Frequency Ratio is adjustable onboard,
please follow the instructions described in the User manual for proper
setup. ncorrect setting will cause damage to your CPU.
The following topics are included in this chapter:
2-1 Pentium 4 CPU Installation
2-2 Pentium 4 CPU Fan Installation
2-3 Memory Installation
2-4 AGP 4X (Accelerated Graphics Port) Installation
2-5 HDD/FDD Installation
2-6 Jumper and Switch Settings
2-7 Other Connectors Configuration
2-8 IRQ Description

16
85DR-C
2-1 Pentium 4 CPU Installation with Socket 478
This series of mainboards are built with CPU Socket 478 (with 478 pins) supporting
the ntel Pentium 4 CPU:
• Follow the steps described in this section to install the 478-pin Pentium 4 CPU
into the on board Socket 478.
• After installation of Pentium 4 CPU, you must also install the specific Pentium 4
CPU fan designed in tandom with this CPU. This CPU Fan installation is described
in next section.
mPGA478B
ntel Pentium 4
3. Make sure that all CPU pins have
completely entered the socket
and then lower down the lever to
lock up CPU to socket.
mPGA478B
ntel Pentium4
2. Configure Pin 1 of CPU to Pin 1
of the Socket, just as the way
shown in the diagram on the
left. Adjust the position of CPU
until you can feel all CPU pins
can get into the socket with
ease.
mPGA478B
Pin 1
1. First pull sideways the lever
of Socket 478, and then turn
it up 90-degree so as to raise
the upper layer of the socket
from the lower platform.

17
Chapter 2 Hardware Setup
2-2 Pentium 4 CPU Fan Installation:
Connect to CPU FAN
connector
Press down 4 latches to lock
fan to fan socket
Pentium 4 Fan Socket
Fan Connector

18
85DR-C
2-3.2 To Remove a DIMM:
• Press down the holding latches on both sides of socket and the module
will be released from the D MM socket.
2-3 Memory Installation
2-3.1 To Install DIMM Module
• This series of mainboards only supports up to 2GB unbuffered DDR
SDRAM, with 2 DDR D MM sockets on board. Do not insert other type of
modules into these sockets.
• DDR D MM socket has 184-pins and one notch. nsert a DDR SDRAM
vertically into the 184-pin socket with the notch matching the one in the
socket. Press the Module down in a gradual way until it surely reaches
the bottom and clicks straight up the two latches on the left and right of
the socket.
How to tackle with the memory Modules
• Make sure to unplug your power supply before adding or removing memory
module. Failure to do so may cause severe damage to both your mainboard
and the memory module.
• Pay attention to the orientation of the D MM slots. Forcing a D MM in a
socket improperly will damage the memory module and socket.
• Make sure you have the right type of memory module for your mainboard.
Key Point: Press the module down gradually until it has totally
reached the socket bottom and clicked up both two socket latches
completely. f any one of the latches has not turned up completely,
you should unplug the module and press it down the socket a bit
more firmly.
184-Pin DIMM Notch Key Definitions(2.5V)
DRAM Key Position Voltage Key Position
2.5V

19
Chapter 2 Hardware Setup
1 4
DIMM1 DIMM2
1
mPGA478B
Intel RG82845-D
Intel RG82845
1 3
FAN2
1 3
FAN3
1 3
FAN1
AGP 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
PCI 6
FWH
WOL1
1 3
LPC I O
Controller
AC'97
Codec
CNR
SW1
ON DIP
1 2 3 4 5
IDE2
IDE1
1
1
1
FDC1
Li
Battery
82801BA
JBAT1
1 3
JP3 JP4
1 3 1 3
JP13
1 3
JP2
1 3
1 3
1 3
RT2
RT1
Peripheral Power Connector
+12 Power Connector
4 3 2 1
Main Power Connector
USB1
1
16
PS 2 MOUSE
PS 2 K B
upper
lower
USB1 USB0
upper
lower
LPT1
COM1COM2
MIC
GAME MIDI PORT
LINE OUT
LINE IN
NJP1
SPEAK RST KEYLOCKPWR LED SUS_LED
IDE_LED IR PWR SMI
30
1
++
--
+-
CD9
CD10
1 4
JAGP1
JAGP2
LED1
SCR1
CMEM1
1
2-4 AGP 4X (Accelerated Graphics Port) Installation
Warning:
• The AGP 4X slot on board supports solely 4X AGP card configuration.
User should not insert 1X / 2X AGP card to this mainboard.
• LED1 AGP Protection ndicator is on board this series. n case inappropriate
AGP card (such as AGP 2X) is inserted into this AGP 4X Slot, LED1 will
light up to warn that AGP installation is inproper. The wrong AGP card
should be replaced; otherwise system cannot be booted.
AGP Accelerator
AGP 4X
LED1
AGP Protection ndicator

20
85DR-C
1 4
DIMM1 DIMM2
1
mPGA478B
Intel RG82845-D
Intel RG82845
1 3
FAN2
1 3
FAN3
1 3
FAN1
AGP 4X
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
PCI 6
FWH
WOL1
1 3
LPC I O
Controller
AC'97
Codec
CNR
SW1
ON DIP
1 2 3 4 5
IDE2
IDE1
1
1
1
FDC1
Li
Battery
82801BA
JBAT1
1 3
JP3 JP4
1 3 1 3
JP13
1 3
JP2
1 3
1 3
1 3
RT2
RT1
Peripheral Power Connector
+12 Power Connector
4 3 2 1
Main Power Connector
USB1
1
16
PS 2 MOUSE
PS 2 K B
upper
lower
USB1 USB0
upper
lower
LPT1
COM1COM2
MIC
GAME MIDI PORT
LINE OUT
LINE IN
NJP1
SPEAK RST KEYLOCKPWR LED SUS_LED
IDE_LED
IR PWR SMI
30
1
++
--
+-
CD9
CD10
1 4
JAGP1
JAGP2
LED1
SCR1
CMEM1
1
• To install HDD (Hard Disk Drive), you may connect the connector of DE
cable to the primary ( DE1) or secondary ( DE2) connector on board, and
then connect the gray connector to your slave device and the black
connector to your master device. f you install two hard disks, you must
configure the second drive to Slave mode by setting its jumpers correctly.
Please refer to your hard disk documentation for the jumper settings.
Hard Disk Drive Connector:
Orient the red line on the DE
ribbon cable to Pin1.
2-5 HDD/FDD Installation
Gray connector
Blue connector
IDE Cable
Black connector
red line