SOLTEK SL-PM800I User manual

5
SL-PM800I / PM800I-L Chapter 1 Specification
1-1 Mainboard Layout and Components Setup
Chapter 1 Specification
VIA
PM800
PCI 1
BIOS
IDE2IDE1
VIA
VIA
1617A
1617A
AC'97
Li
Battery
DIMM1 DIMM2
DDR 400/333/266MHz
mPGA478
1
JKB1
Main Power
JAUD1
PS/2 Mouse
(on top)
NJ1
HDD IR PWR
1
20
SPK RST
+-
+-
PW LED
LED
PCI 2
Fan3
1
JCLK 1
JBAT1
PS/2 Keyboard
AGP1 8X/4X
VT8235
VIA
RJ45
(on top)
Line in
(ontop)
LineOut
(middle)
Mic
PCI 3
1
1
1
JCLK 2
VIA
VIA
6103L
6103L
(2 ports)
1
FDD1
LPT1
COM1
VGA
USB
PW2
+12V Power
PW1
LPC I/O
IT8705F
Fan1
(underside)
(2 ports)
USB
USB3
11
CDIN1
Fan2
For PM800I-L Only
RJ45
LAN Chip VT6103L }
1
USB Cable (Optional)
Red wire
USB Port
1
10
10
CD-ROM Audio Connector
1
10
Black
+5V
Red GreenWhite GNDD2- D2+
Black
GND
Green
D1+
White
D1-+5V
Red
1
CD-In1
Pin 1
Pin 2
Pin 3
Pin 4
Left Channel
GND
GND
Right Channel
Pin Signal
Fast Ethernet
10/100
for
CRT Monitor

6
SL-PM800I / PM800I-L Chapter 1 Specification
Intel Pentium 4 + VIA PM800 + VT8235 Diagram
1-2 Chipset System Block Diagram
Intel Pentium 4 CPU
(Hyper-Threading)
System Bus 800/533/400MHz
System
Memory
DDR 400/333/
266/200 SDRAM
VIA PM800
AGP Slot AGP 8X/4X
8X V-Link
533MB/s
VT8235
PCI Bus
AC’97 2.2
ATA 133/100/66
2 IDE
Connector
USB Bus V2.0/1.1
USB
Ports
3 PCI Slots
Audio
Connectors
VT6103L
(LAN)
RJ45
(Optional)
IR
FDD
Serial Ports
Printer Port
H/Monitor
BIOS
LPC I/O
IT8705F
(6-channel)
Keyboard & Mouse
North Bridge
South
Bridge

7
SL-PM800I / PM800I-L Chapter 1 Specification
1-3 Mainboard Specification Table
SL-PM800I/ PM800I-L Specifications and Features
CPU
South Bridge
North Bridge
Socket 478B for P4 CPU
(including Hyper-threading CPUs)
VT8235
VIA PM800, supporting 800/533/400MHz FSB
No
LAN Controller
on board
Optional
Features
Models
Other common
features
I/O Connectors
PCI Slots
IDE Interface
Audio
AGP interface
I/O Chip
Memory
Keyboard/Mouse Wake Up
6 USB2.0 ports, 1 FDD port, 1 COM port, 1
LPT, 1 IrDA, 1 PS/2 Keyboard, 1 PS/2 Mouse
3 PCI Master slots on board
2 UATA 66/100/133 IDE ports
AC’97 Audio 2.2 compliant, 6 channel audio
Supporting DDR 400/333/266 SDRAM, up to
2GB in 2 DIMM slots
Yes
ITE IT8705F
1 AGP Slot On Board support 4X /8X AGP
PM800I PM800I-L
VGA Integrated VIA Unichrome Pro Graphic

8
SL-PM800I / PM800I-L Chapter 1 Specification
1-4.2 Hyper-Threading CPU supported by Win XP
This mainboard supports Hyper-
threading dual-in-one CPU, the func-
tion of which can be enabled by Win-
dows XP. (See illustration on the
right.)
( If Hyper-Threading CPU is
installed successfully with
Windows XP, the O/S will
enable the dual-in-one CPU
function.)
1-4 Pentium 4 CPU and CPU Fan Installation
1-4.1 CPU Installation with Socket 478B
(3) Pull down the lever to fix
Connect Fan Power cable to onboard
(4) Load down the P4 CPU Fan
(1) Pentium 4 CPU
Pin 1
(2) Pull up the lever and insert P4 CPU
into socket 478
Pin 1

9
SL-PM800I / PM800I-L Chapter 1 Specification
VIA
PM800
PCI 1
BIOS
IDE2IDE1
VIA
VIA
1617A
1617A
AC'97
Li
Battery
DIMM1 DIMM2
DDR 400/333/266MHz
mPGA478
1
JKB1
Main Power
JAUD1
PS/2 Mouse
(on top)
NJ1
HDD IR PWR
1
20
SPK RST
+-
+-
PW LED
LED
PCI 2
Fan3
1
JCLK 1
JBAT1
PS/2 Keyboard
AGP1 8X/4X
VT8235
VIA
RJ45
(on top)
Linein
(on top)
LineOut
(middle)
Mic
PCI 3
1
1
1
JCLK 2
VIA
VIA
6103L
6103L
(2 ports)
1
FDD1
LPT1
COM1
VGA
USB
PW2
+12V Power
PW1
LPC I/O
IT8705F
Fan1
(underside)
(2 ports)
USB
USB3
11
CDIN1
Fan2
1-6 ATX V 2.03 Power Supply Installation
Main Power
Connector
+12V
5SB
PWR OK
GND
GND
GND
GND
GND
GND
+5V
+5V
-5V
+5V
+5V
+3.3V
+3.3V +3.3V
PS ON#
Pin1 Pin11
-12V
GND
Warning: Both the Main
Power Connector and the
+12V Power Connector
should be connected to
Power Supply; otherwise,
the system may either not
start or be damaged.
+12V Power Connector
GND
GND
+12V
+12V
12
34
VIA
PM800
PCI 1
BIOS
IDE2IDE1
VIA
VIA
1617A
1617A
AC'97
Li
Battery
DIMM1 DIMM2
DDR 400/333/266MHz
mPGA478
1
JKB1
Main Power
JAUD1
PS/2 Mouse
(on top)
NJ1
HDD IR PWR
1
20
SPK RST
+-
+-
PW LED
LED
PCI 2
Fan3
1
JCLK 1
JBAT1
PS/2 Keyboard
AGP1 8X/4X
VT8235
VIA
RJ45
(on top)
Linein
(ontop)
LineOut
(middle)
Mic
PCI 3
1
1
1
JCLK 2
VIA
VIA
6103L
6103L
(2 ports)
1
FDD1
LPT1
COM1
VGA
USB
PW2
+12V Power
PW1
LPC I/O
IT8705F
Fan1
(underside)
(2 ports)
USB
USB3
11
CDIN1
Fan2
GND
+12V
SENSO
R
Void
+12V
GND
Sensor No
FAN3, sensor Fan
Connector(Yellow)
FAN2, No-Sensor Fan
Connector
FAN1, Sensor Fan
Connector (Yellow)
1-5 On board Fan Connector Setup

10
SL-PM800I / PM800I-L Chapter 1 Specification
VIA
PM800
PCI 1
BIOS
IDE2IDE1
VIA
VIA
1617A
1617A
AC'97
Li
Battery
DIMM1 DIMM2
DDR 400/333/266MHz
mPGA478
1
JKB1
Main Power
JAUD1
PS/2 Mouse
(on top)
NJ1
HDD IR PWR
1
20
SPK RST +-
+-
PW LED
LED
PCI 2
Fan3
1
JCLK 1
JBAT1
PS/2 Keyboard
AGP1 8X/4X
VT8235
VIA
RJ45
(on top)
Linein
(ontop)
LineOut
(middle)
Mic
PCI 3
1
1
1
JCLK 2
VIA
VIA
6103L
6103L
(2 ports)
1
FDD1
LPT1
COM1
VGA
USB
PW2
+12V Power
PW1
LPC I/O
IT8705F
Fan1
(underside)
(2 ports)
USB
USB3
11
CDIN1
Fan2
1-7 Jumper Settings
The following diagrams show the locations and settings of jumper blocks
on the mainboard.
Keyboard / Mouse
Wake Up
1
1
JKB1:
1-2 closed (default)
Disabled
2-3 closed
Enabled
Clear CMOS
1-2 closed
(default)
To hold data
2-3 closed
To clear CMOS
JBAT1
1
1
(default)
JCLK1&JCLK2: CPU Frequency Select
CPU
Auto-
Detection
100MHz 133MHz 200MHz
(FSB533)
1
JCLK2
11
JCLK1
JCLK2
JCLK1
11
JCLK2
JCLK1
111
JCLK2
JCLK1
(FSB800)
(FSB400)

11
SL-PM800I / PM800I-L Chapter 1 Specification
JAUD1
External Audio Connector
Pin 1 Mic In
Pin 3 Mic VREF
Pin 5 FPOUT R
Pin 7 (Key)
Pin 9 FPOUT L
Pin 2 Aud GND
Pin 6 RET R
Pin 10 RET L
Pin 4 Aud Vcc
(1)Power Switch PLED-
NC
PLED+
RSTGND
RST1
SP1
NC
SP3
SPVCC
PWRBT#
PWRBT
IR_VCC
NC
IRRX
IRGND
IRTX
HDLED-
HDLED+
(2)Infrared(IR)
(3)HDD LED
Power LED (4)
Reset Switch (5)
Speaker (6)
1-8.1 Front Audio Connector
This Mainboard is designed with a Front Panel Audio connector “JAUD1”
which provides connection to your chassis.
1. When JAUD1 is set to 5-6 closed and 9-10 closed, this default setting
disables this connector and leaves the Back Panel Audio enabled.
2. To use this Front Panel Audio Connector, please open all pins of
JAUD1 and connect it to your chassis.
1-8 Other Connectors Setup
VIA
PM800
PCI 1
BIOS
IDE2IDE1
VIA
VIA
1617A
1617A
AC'97
Li
Battery
DIMM1 DIMM2
DDR 400/333/266MHz
mPGA478
1
JKB1
Main Power
JAUD1
PS/2 Mouse
(on top)
NJ1
HDD IR PWR
1
20
SPK RST
+-
+-
PW LED
LED
PCI 2
Fan3
1
JCLK 1
JBAT1
PS/2 Keyboard
AGP1 8X/4X
VT8235
VIA
RJ45
(on top)
Linein
(ontop)
LineOut
(middle)
Mic
PCI 3
1
1
1
JCLK 2
VIA
VIA
6103L
6103L
(2 ports)
1
FDD1
LPT1
COM1
VGA
USB
PW2
+12V Power
PW1
LPC I/O
IT8705F
Fan1
(underside)
(2 ports)
USB
USB3
11
CDIN1
Fan2
Front Panel Connectors Illustration
1-8.2 Complex Header (Front Panel Connectors)
This complex Header consists of 6 connectors providing various
supports:

12
SL-PM800I / PM800I-L Chapter 2 Software Setup
Chapter 2 Software Setup
1. Please put the Support CD enclosed in your mainboard package into
the CD-ROM drive. In a few seconds, the Main Menu will automatic-
ally appear, displaying the contents to be installed for this series:
2. Start driver and software installation from the first item and finish all
to optimize your system.
2-2.1 LAN Driver Installation (for PM800I-L)
2-2 Some Installation Illustrations
2-2.2 LAN Driver Verification
1. After LAN Driver setup, a new networking icon will appear at the
corner of the “Start” screen of your system, indicating that a network
channel has been set up.
2. Instantly, “The installation is
completed” screen appears,
indicating that LAN Driver
setup is finished.
1. Following the procedures of
opening the Support CD, click to “
Onboard LAN Driver” to proceed.
VIA USB 2.0 Driver
DirectX
Graphics Driver
AC’97 Audio Driver
Onboard LAN Driver (Optional)
Hardware Monitor Utility
VIA 4 in 1 Driver
2-1 To Open up the Support CD

13
SL-PM800I / PM800I-L Chapter 2 Software Setup
2. Instantly, the “installShield Wizard”
screen appears to guide you through
the “Realtek AC’97 Audio Setup””.
1. Following the procedures of opening the Support CD, click to “ AC’97
Audio Driver” to proceed.
2-2.3 Installing AC’97 6-channel Audio Driver
3. In a few seconds, the setup process
is finished. Please check the radial
button “Yes, I want to restart my
computer now.” And click “Finish” to
restart your system.
2-2.4 Verifying 6-channel Audio
1. Start your Windows system and double click the Avance Sound Effect
manager icon to enter 6-channel configuration:
2. The AC’97 Audio Configuration” screen will pop out. Clikc the “Speaker
Configuration” bar with your mouse.
4. At finishing the Speakers Configuration, you can also click the
“Speaker Test” bar on the screen to test the 6-channel performance.
The figure below is the “Speaker Test” screen with testing instructions
enclosed on it. Follow the instructions to perform the Speakers Test.
3. Instantly, the “Speaker Configuration” screen will pop out. Pick the
items “6-channel mode for 5.1 speakers output” and “ Synchronize
the phonejack switch with the speakers settings” and then click “OK”
to finish configuration.
“Speaker Configuration”
“6-channel mode for 5.1 speakers output”
“ Synchronize the phonejack switch with the speakers settings”
“The Speakers Test”

14
SL-PM800I / PM800I-L Chapter 2 Software Setup
2-2.5 To Install USB 2.0 Driver
VIA USB V2.0 is already integrated on board. Its 480Mb/s transfer rate
supports operating systems Windows 98SE/ME/2000/XP. USB2.0
Driver is typically for Windows 98SE/ME. For Windows 2000/XP, users
can install their latest Service Pack instead of the USB2.0 driver to gain
the USB2.0 support. For the Windows system which is not installed
with its latest Service Pack, users must install the USB2.0 driver to
activate the USB2.0 support:
1. Following the procedures of opening the Support CD, click to choose
“VIA USB 2.0 Driver” to proceed. Please notice that the USB card
driver is different from the USB 2.0 driver typically for the on-board
USB. Do not use the USB card driver here.
kÉñí
kÉñí
2. “USB 2.0 Setup program ” will pop up.
Click “Next” to continue.
3. Select “Install USB Driver” and click
“Next” button to continue.
4. Please click “Finish” button to restart
system to put the new driver into effect.
cáåáëÜ